All of lore.kernel.org
 help / color / mirror / Atom feed
From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH 06/11] arm64: dts: qcom: db820c: Sort all nodes
Date: Sun, 20 Oct 2019 22:13:17 -0700	[thread overview]
Message-ID: <20191021051322.297560-7-bjorn.andersson@linaro.org> (raw)
In-Reply-To: <20191021051322.297560-1-bjorn.andersson@linaro.org>

Sort all nodes in db820c.dtsi based on address, then name.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 336 +++++++++----------
 1 file changed, 168 insertions(+), 168 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index aed34a461b19..99990a139938 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -124,6 +124,18 @@
 	};
 };
 
+&blsp1_i2c2 {
+	/* On Low speed expansion */
+	label = "LS-I2C0";
+	status = "okay";
+};
+
+&blsp1_spi0 {
+	/* On Low speed expansion */
+	label = "LS-SPI0";
+	status = "okay";
+};
+
 &blsp1_uart1 {
 	label = "BT-UART";
 	status = "okay";
@@ -141,6 +153,24 @@
 	};
 };
 
+&blsp2_i2c0 {
+	/* On High speed expansion */
+	label = "HS-I2C2";
+	status = "okay";
+};
+
+&blsp2_i2c1 {
+	/* On Low speed expansion */
+	label = "LS-I2C1";
+	status = "okay";
+};
+
+&blsp2_spi5 {
+	/* On High speed expansion */
+	label = "HS-SPI1";
+	status = "okay";
+};
+
 &blsp2_uart1 {
 	label = "LS-UART1";
 	status = "okay";
@@ -157,75 +187,49 @@
 	pinctrl-1 = <&blsp2_uart2_4pins_sleep>;
 };
 
-&blsp1_i2c2 {
-	/* On Low speed expansion */
-	label = "LS-I2C0";
-	status = "okay";
+&camss {
+	vdda-supply = <&pm8994_l2>;
 };
 
-&blsp2_i2c1 {
-	/* On Low speed expansion */
-	label = "LS-I2C1";
+&hdmi {
 	status = "okay";
-};
 
-&blsp1_spi0 {
-	/* On Low speed expansion */
-	label = "LS-SPI0";
-	status = "okay";
-};
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
+	pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
 
-&blsp2_i2c0 {
-	/* On High speed expansion */
-	label = "HS-I2C2";
-	status = "okay";
+	core-vdda-supply = <&pm8994_l12>;
+	core-vcc-supply = <&pm8994_s4>;
 };
 
-&blsp2_spi5 {
-	/* On High speed expansion */
-	label = "HS-SPI1";
+&hdmi_phy {
 	status = "okay";
-};
 
-&camss {
-	vdda-supply = <&pm8994_l2>;
+	vddio-supply = <&pm8994_l12>;
+	vcca-supply = <&pm8994_l28>;
+	#phy-cells = <0>;
 };
 
-&sdhc2 {
-	/* External SD card */
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
-	cd-gpios = <&msmgpio 38 0x1>;
-	vmmc-supply = <&pm8994_l21>;
-	vqmmc-supply = <&pm8994_l13>;
+&hsusb_phy1 {
 	status = "okay";
+
+	vdda-pll-supply = <&pm8994_l12>;
+	vdda-phy-dpdm-supply = <&pm8994_l24>;
 };
 
-&ufsphy {
+&hsusb_phy2 {
 	status = "okay";
 
-	vdda-phy-supply = <&pm8994_l28>;
 	vdda-pll-supply = <&pm8994_l12>;
-
-	vdda-phy-max-microamp = <18380>;
-	vdda-pll-max-microamp = <9440>;
-
-	vddp-ref-clk-supply = <&pm8994_l25>;
-	vddp-ref-clk-max-microamp = <100>;
-	vddp-ref-clk-always-on;
+	vdda-phy-dpdm-supply = <&pm8994_l24>;
 };
 
-&ufshc {
+&mdp {
 	status = "okay";
+};
 
-	vcc-supply = <&pm8994_l20>;
-	vccq-supply = <&pm8994_l25>;
-	vccq2-supply = <&pm8994_s4>;
-
-	vcc-max-microamp = <600000>;
-	vccq-max-microamp = <450000>;
-	vccq2-max-microamp = <450000>;
+&mdss {
+	status = "okay";
 };
 
 &msmgpio {
@@ -382,6 +386,32 @@
 		"NC"; /* GPIO_149 */
 };
 
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+	vddpe-3v3-supply = <&wlan_en>;
+	vdda-supply = <&pm8994_l28>;
+};
+
+&pcie1 {
+	status = "okay";
+	perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&pm8994_l28>;
+};
+
+&pcie2 {
+	status = "okay";
+	perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&pm8994_l28>;
+};
+
+&pcie_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&pm8994_l28>;
+	vdda-pll-supply = <&pm8994_l12>;
+};
+
 &pm8994_gpios {
 	gpio-line-names =
 		"NC",
@@ -434,114 +464,6 @@
 		"NC";
 };
 
-&pcie_phy {
-	status = "okay";
-
-	vdda-phy-supply = <&pm8994_l28>;
-	vdda-pll-supply = <&pm8994_l12>;
-};
-
-&usb3phy {
-	status = "okay";
-
-	vdda-phy-supply = <&pm8994_l28>;
-	vdda-pll-supply = <&pm8994_l12>;
-
-};
-
-&hsusb_phy1 {
-	status = "okay";
-
-	vdda-pll-supply = <&pm8994_l12>;
-	vdda-phy-dpdm-supply = <&pm8994_l24>;
-};
-
-&hsusb_phy2 {
-	status = "okay";
-
-	vdda-pll-supply = <&pm8994_l12>;
-	vdda-phy-dpdm-supply = <&pm8994_l24>;
-};
-
-&usb3 {
-	status = "okay";
-	extcon = <&usb3_id>;
-
-	dwc3@6a00000 {
-		extcon = <&usb3_id>;
-		dr_mode = "otg";
-	};
-};
-
-&usb2 {
-	status = "okay";
-	extcon = <&usb2_id>;
-
-	dwc3@7600000 {
-		extcon = <&usb2_id>;
-		dr_mode = "otg";
-		maximum-speed = "high-speed";
-	};
-};
-
-&pcie0 {
-	status = "okay";
-	perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
-	vddpe-3v3-supply = <&wlan_en>;
-	vdda-supply = <&pm8994_l28>;
-};
-
-&pcie1 {
-	status = "okay";
-	perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
-	vdda-supply = <&pm8994_l28>;
-};
-
-&pcie2 {
-	status = "okay";
-	perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
-	vdda-supply = <&pm8994_l28>;
-};
-
-&wcd9335 {
-	clock-names = "mclk", "slimbus";
-	clocks = <&div1_mclk>,
-		 <&rpmcc RPM_SMD_BB_CLK1>;
-
-	vdd-buck-supply = <&pm8994_s4>;
-	vdd-buck-sido-supply = <&pm8994_s4>;
-	vdd-tx-supply = <&pm8994_s4>;
-	vdd-rx-supply = <&pm8994_s4>;
-	vdd-io-supply = <&pm8994_s4>;
-};
-
-&mdss {
-	status = "okay";
-};
-
-&mdp {
-	status = "okay";
-};
-
-&hdmi_phy {
-	status = "okay";
-
-	vddio-supply = <&pm8994_l12>;
-	vcca-supply = <&pm8994_l28>;
-	#phy-cells = <0>;
-};
-
-&hdmi {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
-	pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
-
-	core-vdda-supply = <&pm8994_l12>;
-	core-vcc-supply = <&pm8994_s4>;
-};
-
 &rpm_requests {
 	pm8994-regulators {
 		compatible = "qcom,rpm-pm8994-regulators";
@@ -698,18 +620,15 @@
 	};
 };
 
-&spmi_bus {
-	pmic@0 {
-		pon@800 {
-			resin {
-				compatible = "qcom,pm8941-resin";
-				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
-				debounce = <15625>;
-				bias-pull-up;
-				linux,code = <KEY_VOLUMEDOWN>;
-			};
-		};
-	};
+&sdhc2 {
+	/* External SD card */
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	cd-gpios = <&msmgpio 38 0x1>;
+	vmmc-supply = <&pm8994_l21>;
+	vqmmc-supply = <&pm8994_l13>;
+	status = "okay";
 };
 
 &sound {
@@ -783,3 +702,84 @@
 		};
 	};
 };
+
+&spmi_bus {
+	pmic@0 {
+		pon@800 {
+			resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_VOLUMEDOWN>;
+			};
+		};
+	};
+};
+
+&ufsphy {
+	status = "okay";
+
+	vdda-phy-supply = <&pm8994_l28>;
+	vdda-pll-supply = <&pm8994_l12>;
+
+	vdda-phy-max-microamp = <18380>;
+	vdda-pll-max-microamp = <9440>;
+
+	vddp-ref-clk-supply = <&pm8994_l25>;
+	vddp-ref-clk-max-microamp = <100>;
+	vddp-ref-clk-always-on;
+};
+
+&ufshc {
+	status = "okay";
+
+	vcc-supply = <&pm8994_l20>;
+	vccq-supply = <&pm8994_l25>;
+	vccq2-supply = <&pm8994_s4>;
+
+	vcc-max-microamp = <600000>;
+	vccq-max-microamp = <450000>;
+	vccq2-max-microamp = <450000>;
+};
+
+&usb2 {
+	status = "okay";
+	extcon = <&usb2_id>;
+
+	dwc3@7600000 {
+		extcon = <&usb2_id>;
+		dr_mode = "otg";
+		maximum-speed = "high-speed";
+	};
+};
+
+&usb3 {
+	status = "okay";
+	extcon = <&usb3_id>;
+
+	dwc3@6a00000 {
+		extcon = <&usb3_id>;
+		dr_mode = "otg";
+	};
+};
+
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&pm8994_l28>;
+	vdda-pll-supply = <&pm8994_l12>;
+
+};
+
+&wcd9335 {
+	clock-names = "mclk", "slimbus";
+	clocks = <&div1_mclk>,
+		 <&rpmcc RPM_SMD_BB_CLK1>;
+
+	vdd-buck-supply = <&pm8994_s4>;
+	vdd-buck-sido-supply = <&pm8994_s4>;
+	vdd-tx-supply = <&pm8994_s4>;
+	vdd-rx-supply = <&pm8994_s4>;
+	vdd-io-supply = <&pm8994_s4>;
+};
-- 
2.23.0


  parent reply	other threads:[~2019-10-21  5:14 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-21  5:13 [PATCH 00/11] arm64: dts: qcom: msm8996: Introduce IFC6640 Bjorn Andersson
2019-10-21  5:13 ` [PATCH 01/11] arm64: dts: qcom: db820c: Move non-soc entries out of /soc Bjorn Andersson
2019-10-21  5:13 ` [PATCH 02/11] arm64: dts: qcom: msm8996: Use node references in db820c Bjorn Andersson
2019-10-21  5:13 ` [PATCH 03/11] arm64: dts: qcom: msm8996: Move regulator consumers to db820c Bjorn Andersson
2019-10-21  5:13 ` [PATCH 04/11] arm64: dts: qcom: msm8996: Move regulators " Bjorn Andersson
2019-10-21  5:13 ` [PATCH 05/11] arm64: dts: qcom: db820c: Group root nodes Bjorn Andersson
2019-10-21  5:13 ` Bjorn Andersson [this message]
2019-10-21  5:13 ` [PATCH 07/11] arm64: dts: qcom: db820c: Remove pin specific files Bjorn Andersson
2019-10-21  5:13 ` [PATCH 08/11] arm64: dts: qcom: msm8996: Pad addresses Bjorn Andersson
2019-10-21  5:13 ` [PATCH 09/11] arm64: dts: qcom: msm8996: Sort all nodes in msm8996.dtsi Bjorn Andersson
2019-10-21  5:13 ` [PATCH 10/11] arm64: dts: qcom: db820c: Use regulator names from schematics Bjorn Andersson
2019-10-21  5:13 ` [PATCH 11/11] arm64: dts: qcom: msm8996: Introduce IFC6640 Bjorn Andersson
2019-11-03  8:13 ` [PATCH 00/11] " Vinod Koul
2019-11-04  4:55   ` Bjorn Andersson
2019-11-04  9:27     ` Vinod Koul

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191021051322.297560-7-bjorn.andersson@linaro.org \
    --to=bjorn.andersson@linaro.org \
    --cc=agross@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.