[PATCH v3 4/7] clk: meson: a1: add support for Amlogic A1 PLL clock driver

[Jian Hu <jian.hu@amlogic.com>]

The Amlogic A1 clock includes three drivers:
pll clocks, peripheral clocks, CPU clocks.
sys pll and CPU clocks will be sent in next patch.

Unlike the previous series, there is no EE/AO domain
in A1 CLK controllers.

Signed-off-by: Jian Hu <jian.hu@amlogic.com>
---
 drivers/clk/meson/Kconfig  |  10 ++
 drivers/clk/meson/Makefile |   1 +
 drivers/clk/meson/a1-pll.c | 334 +++++++++++++++++++++++++++++++++++++
 drivers/clk/meson/a1-pll.h |  56 +++++++
 4 files changed, 401 insertions(+)
 create mode 100644 drivers/clk/meson/a1-pll.c
 create mode 100644 drivers/clk/meson/a1-pll.h

diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index dabeb435d067..14e7936ae18e 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -93,6 +93,16 @@ config COMMON_CLK_AXG_AUDIO
 	  Support for the audio clock controller on AmLogic A113D devices,
 	  aka axg, Say Y if you want audio subsystem to work.
 
+config COMMON_CLK_A1_PLL
+	bool
+	depends on ARCH_MESON
+	select COMMON_CLK_MESON_EE_CLKC
+	select COMMON_CLK_MESON_REGMAP
+	select COMMON_CLK_MESON_PLL
+	help
+	  Support for the PLL clock controller on Amlogic A113L device,
+	  aka a1. Say Y if you want PLL to work.
+
 config COMMON_CLK_G12A
 	bool
 	depends on ARCH_MESON
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 3939f218587a..71d3b8e6fb8a 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
 
 obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
 obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
+obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
 obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
 obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
 obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
new file mode 100644
index 000000000000..b248ac81ddd8
--- /dev/null
+++ b/drivers/clk/meson/a1-pll.c
@@ -0,0 +1,334 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <jian.hu@amlogic.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "a1-pll.h"
+#include "clk-pll.h"
+#include "meson-eeclk.h"
+
+static struct clk_regmap a1_fixed_pll_dco = {
+	.data = &(struct meson_clk_pll_data){
+		.en = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 28,
+			.width   = 1,
+		},
+		.m = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 0,
+			.width   = 8,
+		},
+		.n = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 10,
+			.width   = 5,
+		},
+		.frac = {
+			.reg_off = ANACTRL_FIXPLL_CTRL1,
+			.shift   = 0,
+			.width   = 19,
+		},
+		.l = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 31,
+			.width   = 1,
+		},
+		.rst = {
+			.reg_off = ANACTRL_FIXPLL_CTRL0,
+			.shift   = 29,
+			.width   = 1,
+		},
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fixed_pll_dco",
+		.ops = &meson_clk_pll_ro_ops,
+		.parent_data = &(const struct clk_parent_data){
+			.fw_name = "xtal_fixpll",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fixed_pll = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 20,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "fixed_pll",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll_dco.hw
+		},
+		.num_parents = 1,
+		/*
+		 * This clock is fclk_div2/3/5's parent,
+		 * However, fclk_div2/3/5 feeds AXI/APB/DDR.
+		 * It is required by the platform to operate correctly.
+		 */
+		.flags = CLK_IGNORE_UNUSED,
+	},
+};
+
+static const struct pll_mult_range a1_hifi_pll_mult_range = {
+	.min = 32,
+	.max = 64,
+};
+
+static const struct reg_sequence a1_hifi_init_regs[] = {
+	{ .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x100a1100 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00302000 },
+	{ .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f18440 },
+};
+
+static struct clk_regmap a1_hifi_pll = {
+	.data = &(struct meson_clk_pll_data){
+		.en = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 28,
+			.width   = 1,
+		},
+		.m = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 0,
+			.width   = 8,
+		},
+		.n = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 10,
+			.width   = 5,
+		},
+		.frac = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL1,
+			.shift   = 0,
+			.width   = 19,
+		},
+		.l = {
+			.reg_off = ANACTRL_HIFIPLL_STS,
+			.shift   = 31,
+			.width   = 1,
+		},
+		.current_en = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL0,
+			.shift   = 26,
+			.width   = 1,
+		},
+		.rst = {
+			.reg_off = ANACTRL_HIFIPLL_CTRL2,
+			.shift   = 6,
+			.width   = 1,
+		},
+		.range = &a1_hifi_pll_mult_range,
+		.init_regs = a1_hifi_init_regs,
+		.init_count = ARRAY_SIZE(a1_hifi_init_regs),
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "hifi_pll",
+		.ops = &meson_clk_pll_ops,
+		.parent_data = &(const struct clk_parent_data){
+			.fw_name = "xtal_hifipll",
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div2_div = {
+	.mult = 1,
+	.div = 2,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div2_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div2 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 21,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div2",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div2_div.hw
+		},
+		.num_parents = 1,
+		/*
+		 * This clock is used by DDR clock in BL2 firmware
+		 * and is required by the platform to operate correctly.
+		 * Until the following condition are met, we need this clock to
+		 * be marked as critical:
+		 * a) Mark the clock used by a firmware resource, if possible
+		 * b) CCF has a clock hand-off mechanism to make the sure the
+		 *    clock stays on until the proper driver comes along
+		 */
+		.flags = CLK_IS_CRITICAL,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div3_div = {
+	.mult = 1,
+	.div = 3,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div3_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div3 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 22,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div3",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div3_div.hw
+		},
+		.num_parents = 1,
+		/*
+		 * This clock is used by APB bus which setted in Romcode
+		 * and is required by the platform to operate correctly.
+		 * Until the following condition are met, we need this clock to
+		 * be marked as critical:
+		 * a) Mark the clock used by a firmware resource, if possible
+		 * b) CCF has a clock hand-off mechanism to make the sure the
+		 *    clock stays on until the proper driver comes along
+		 */
+		.flags = CLK_IS_CRITICAL,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div5_div = {
+	.mult = 1,
+	.div = 5,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div5_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div5 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 23,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div5",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div5_div.hw
+		},
+		.num_parents = 1,
+		/*
+		 * This clock is used by AXI bus which setted in Romcode
+		 * and is required by the platform to operate correctly.
+		 * Until the following condition are met, we need this clock to
+		 * be marked as critical:
+		 * a) Mark the clock used by a firmware resource, if possible
+		 * b) CCF has a clock hand-off mechanism to make the sure the
+		 *    clock stays on until the proper driver comes along
+		 */
+		.flags = CLK_IS_CRITICAL,
+	},
+};
+
+static struct clk_fixed_factor a1_fclk_div7_div = {
+	.mult = 1,
+	.div = 7,
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div7_div",
+		.ops = &clk_fixed_factor_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fixed_pll.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap a1_fclk_div7 = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = ANACTRL_FIXPLL_CTRL0,
+		.bit_idx = 24,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "fclk_div7",
+		.ops = &clk_regmap_gate_ops,
+		.parent_hws = (const struct clk_hw *[]) {
+			&a1_fclk_div7_div.hw
+		},
+		.num_parents = 1,
+	},
+};
+
+/* Array of all clocks provided by this provider */
+static struct clk_hw_onecell_data a1_pll_hw_onecell_data = {
+	.hws = {
+		[CLKID_FIXED_PLL_DCO]		= &a1_fixed_pll_dco.hw,
+		[CLKID_FIXED_PLL]		= &a1_fixed_pll.hw,
+		[CLKID_HIFI_PLL]		= &a1_hifi_pll.hw,
+		[CLKID_FCLK_DIV2]		= &a1_fclk_div2.hw,
+		[CLKID_FCLK_DIV3]		= &a1_fclk_div3.hw,
+		[CLKID_FCLK_DIV5]		= &a1_fclk_div5.hw,
+		[CLKID_FCLK_DIV7]		= &a1_fclk_div7.hw,
+		[CLKID_FCLK_DIV2_DIV]		= &a1_fclk_div2_div.hw,
+		[CLKID_FCLK_DIV3_DIV]		= &a1_fclk_div3_div.hw,
+		[CLKID_FCLK_DIV5_DIV]		= &a1_fclk_div5_div.hw,
+		[CLKID_FCLK_DIV7_DIV]		= &a1_fclk_div7_div.hw,
+		[NR_PLL_CLKS]			= NULL,
+	},
+	.num = NR_PLL_CLKS,
+};
+
+static struct clk_regmap *const a1_pll_regmaps[] = {
+	&a1_fixed_pll_dco,
+	&a1_fixed_pll,
+	&a1_hifi_pll,
+	&a1_fclk_div2,
+	&a1_fclk_div3,
+	&a1_fclk_div5,
+	&a1_fclk_div7,
+};
+
+static const struct meson_eeclkc_data a1_pll_data = {
+		.regmap_clks = a1_pll_regmaps,
+		.regmap_clk_num = ARRAY_SIZE(a1_pll_regmaps),
+		.hw_onecell_data = &a1_pll_hw_onecell_data,
+};
+static const struct of_device_id clkc_match_table[] = {
+	{
+		.compatible = "amlogic,a1-pll-clkc",
+		.data = &a1_pll_data
+	},
+	{}
+};
+
+static struct platform_driver a1_pll_driver = {
+	.probe		= meson_clkc_probe,
+	.driver		= {
+		.name	= "a1-pll-clkc",
+		.of_match_table = clkc_match_table,
+	},
+};
+
+builtin_platform_driver(a1_pll_driver);
diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
new file mode 100644
index 000000000000..8ded267061ad
--- /dev/null
+++ b/drivers/clk/meson/a1-pll.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ */
+
+#ifndef __A1_PLL_H
+#define __A1_PLL_H
+
+/* PLL register offset */
+#define ANACTRL_FIXPLL_CTRL0		0x0
+#define ANACTRL_FIXPLL_CTRL1		0x4
+#define ANACTRL_FIXPLL_CTRL2		0x8
+#define ANACTRL_FIXPLL_CTRL3		0xc
+#define ANACTRL_FIXPLL_CTRL4		0x10
+#define ANACTRL_FIXPLL_STS		0x14
+#define ANACTRL_SYSPLL_CTRL0		0x80
+#define ANACTRL_SYSPLL_CTRL1		0x84
+#define ANACTRL_SYSPLL_CTRL2		0x88
+#define ANACTRL_SYSPLL_CTRL3		0x8c
+#define ANACTRL_SYSPLL_CTRL4		0x90
+#define ANACTRL_SYSPLL_STS		0x94
+#define ANACTRL_HIFIPLL_CTRL0		0xc0
+#define ANACTRL_HIFIPLL_CTRL1		0xc4
+#define ANACTRL_HIFIPLL_CTRL2		0xc8
+#define ANACTRL_HIFIPLL_CTRL3		0xcc
+#define ANACTRL_HIFIPLL_CTRL4		0xd0
+#define ANACTRL_HIFIPLL_STS		0xd4
+#define ANACTRL_AUDDDS_CTRL0		0x100
+#define ANACTRL_AUDDDS_CTRL1		0x104
+#define ANACTRL_AUDDDS_CTRL2		0x108
+#define ANACTRL_AUDDDS_CTRL3		0x10c
+#define ANACTRL_AUDDDS_CTRL4		0x110
+#define ANACTRL_AUDDDS_STS		0x114
+#define ANACTRL_MISCTOP_CTRL0		0x140
+#define ANACTRL_POR_CNTL		0x188
+
+/*
+ * CLKID index values
+ *
+ * These indices are entirely contrived and do not map onto the hardware.
+ * It has now been decided to expose everything by default in the DT header:
+ * include/dt-bindings/clock/a1-pll-clkc.h. Only the clocks ids we don't want
+ * to expose, such as the internal muxes and dividers of composite clocks,
+ * will remain defined here.
+ */
+#define CLKID_FIXED_PLL_DCO		0
+#define CLKID_FCLK_DIV2_DIV		2
+#define CLKID_FCLK_DIV3_DIV		3
+#define CLKID_FCLK_DIV5_DIV		4
+#define CLKID_FCLK_DIV7_DIV		5
+#define NR_PLL_CLKS			11
+
+/* include the CLKIDs that have been made part of the DT binding */
+#include <dt-bindings/clock/a1-pll-clkc.h>
+
+#endif /* __A1_PLL_H */
-- 
2.24.0