All of lore.kernel.org
 help / color / mirror / Atom feed
From: Kamel Bouhara <kamel.bouhara@bootlin.com>
To: Nicolas Ferre <nicolas.ferre@microchip.com>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	Ludovic Desroches <ludovic.desroches@microchip.com>,
	linux-arm-kernel@lists.infradead.org,
	Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org,
	Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
	Kamel Bouhara <kamel.bouhara@bootlin.com>
Subject: [PATCH v2] ARM: dts: at91: rearrange kizbox dts using aliases nodes
Date: Thu,  5 Dec 2019 23:23:44 +0100	[thread overview]
Message-ID: <20191205222344.1367147-1-kamel.bouhara@bootlin.com> (raw)

Use aliases nodes to easy kizbox dts readability.

Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
---
Changes in v2:
	- Fixed some missing aliases label from dtsi

 arch/arm/boot/dts/at91-kizbox.dts  | 172 ++++++++++++++---------------
 arch/arm/boot/dts/at91sam9260.dtsi |   2 +-
 2 files changed, 85 insertions(+), 89 deletions(-)

diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 90996eaf73b2..644009a157d6 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -28,85 +28,6 @@
 		};
 	};

-	ahb {
-		apb {
-			tcb0: timer@fffa0000 {
-				timer@0 {
-					compatible = "atmel,tcb-timer";
-					reg = <0>, <1>;
-				};
-
-				timer@2 {
-					compatible = "atmel,tcb-timer";
-					reg = <2>;
-				};
-			};
-
-			macb0: ethernet@fffc4000 {
-				phy-mode = "mii";
-				pinctrl-0 = <&pinctrl_macb_rmii
-				             &pinctrl_macb_rmii_mii_alt>;
-				status = "okay";
-			};
-
-			usart3: serial@fffd0000 {
-				status = "okay";
-			};
-
-			dbgu: serial@fffff200 {
-				status = "okay";
-			};
-
-			watchdog@fffffd40 {
-				timeout-sec = <15>;
-				atmel,max-heartbeat-sec = <16>;
-				atmel,min-heartbeat-sec = <0>;
-				status = "okay";
-			};
-		};
-
-		usb0: ohci@500000 {
-			num-ports = <1>;
-			status = "okay";
-		};
-
-		ebi: ebi@10000000 {
-			status = "okay";
-
-			nand_controller: nand-controller {
-				status = "okay";
-				pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
-				pinctrl-names = "default";
-
-				nand@3 {
-					reg = <0x3 0x0 0x800000>;
-					rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
-					nand-bus-width = <8>;
-					nand-ecc-mode = "soft";
-					nand-on-flash-bbt;
-					label = "atmel_nand";
-
-					partitions {
-						compatible = "fixed-partitions";
-						#address-cells = <1>;
-						#size-cells = <1>;
-
-						bootstrap@0 {
-							label = "bootstrap";
-							reg = <0x0 0x20000>;
-						};
-
-						ubi@20000 {
-							label = "ubi";
-							reg = <0x20000 0x7fe0000>;
-						};
-					};
-				};
-			};
-		};
-	};
-
 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
@@ -127,15 +48,6 @@
 		};
 	};

-	i2c-gpio-0 {
-		status = "okay";
-
-		rtc: pcf8563@51 {
-			compatible = "nxp,pcf8563";
-			reg = <0x51>;
-		};
-	};
-
 	pwm_leds {
 		compatible = "pwm-leds";

@@ -179,3 +91,87 @@
 			     &pinctrl_tcb1_tiob0>;
 	};
 };
+
+&tcb0 {
+	timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>, <1>;
+	};
+
+	timer@2 {
+		compatible = "atmel,tcb-timer";
+		reg = <2>;
+	};
+};
+
+&ebi {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+	pinctrl-names = "default";
+
+	nand@3 {
+		reg = <0x3 0x0 0x800000>;
+		rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "soft";
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			ubi@20000 {
+				label = "ubi";
+				reg = <0x20000 0x7fe0000>;
+			};
+		};
+	};
+};
+
+&macb0 {
+	phy-mode = "mii";
+	pinctrl-0 = <&pinctrl_macb_rmii
+		     &pinctrl_macb_rmii_mii_alt>;
+	status = "okay";
+};
+
+&usart3 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&watchdog {
+	timeout-sec = <15>;
+	atmel,max-heartbeat-sec = <16>;
+	atmel,min-heartbeat-sec = <0>;
+	status = "okay";
+};
+
+&usb0 {
+	num-ports = <1>;
+	status = "okay";
+};
+
+&i2c-gpio-0 {
+	status = "okay";
+
+	rtc: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index dee9c0c8a096..9f9ee3cd7375 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -738,7 +738,7 @@
 				status = "disabled";
 			};

-			watchdog@fffffd40 {
+			watchdog: watchdog@fffffd40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffd40 0x10>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
--
2.24.0


WARNING: multiple messages have this Message-ID (diff)
From: Kamel Bouhara <kamel.bouhara@bootlin.com>
To: Nicolas Ferre <nicolas.ferre@microchip.com>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	Ludovic Desroches <ludovic.desroches@microchip.com>,
	linux-arm-kernel@lists.infradead.org,
	Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org,
	Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
	Kamel Bouhara <kamel.bouhara@bootlin.com>
Subject: [PATCH v2] ARM: dts: at91: rearrange kizbox dts using aliases nodes
Date: Thu,  5 Dec 2019 23:23:44 +0100	[thread overview]
Message-ID: <20191205222344.1367147-1-kamel.bouhara@bootlin.com> (raw)

Use aliases nodes to easy kizbox dts readability.

Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
---
Changes in v2:
	- Fixed some missing aliases label from dtsi

 arch/arm/boot/dts/at91-kizbox.dts  | 172 ++++++++++++++---------------
 arch/arm/boot/dts/at91sam9260.dtsi |   2 +-
 2 files changed, 85 insertions(+), 89 deletions(-)

diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 90996eaf73b2..644009a157d6 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -28,85 +28,6 @@
 		};
 	};

-	ahb {
-		apb {
-			tcb0: timer@fffa0000 {
-				timer@0 {
-					compatible = "atmel,tcb-timer";
-					reg = <0>, <1>;
-				};
-
-				timer@2 {
-					compatible = "atmel,tcb-timer";
-					reg = <2>;
-				};
-			};
-
-			macb0: ethernet@fffc4000 {
-				phy-mode = "mii";
-				pinctrl-0 = <&pinctrl_macb_rmii
-				             &pinctrl_macb_rmii_mii_alt>;
-				status = "okay";
-			};
-
-			usart3: serial@fffd0000 {
-				status = "okay";
-			};
-
-			dbgu: serial@fffff200 {
-				status = "okay";
-			};
-
-			watchdog@fffffd40 {
-				timeout-sec = <15>;
-				atmel,max-heartbeat-sec = <16>;
-				atmel,min-heartbeat-sec = <0>;
-				status = "okay";
-			};
-		};
-
-		usb0: ohci@500000 {
-			num-ports = <1>;
-			status = "okay";
-		};
-
-		ebi: ebi@10000000 {
-			status = "okay";
-
-			nand_controller: nand-controller {
-				status = "okay";
-				pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
-				pinctrl-names = "default";
-
-				nand@3 {
-					reg = <0x3 0x0 0x800000>;
-					rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
-					nand-bus-width = <8>;
-					nand-ecc-mode = "soft";
-					nand-on-flash-bbt;
-					label = "atmel_nand";
-
-					partitions {
-						compatible = "fixed-partitions";
-						#address-cells = <1>;
-						#size-cells = <1>;
-
-						bootstrap@0 {
-							label = "bootstrap";
-							reg = <0x0 0x20000>;
-						};
-
-						ubi@20000 {
-							label = "ubi";
-							reg = <0x20000 0x7fe0000>;
-						};
-					};
-				};
-			};
-		};
-	};
-
 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
@@ -127,15 +48,6 @@
 		};
 	};

-	i2c-gpio-0 {
-		status = "okay";
-
-		rtc: pcf8563@51 {
-			compatible = "nxp,pcf8563";
-			reg = <0x51>;
-		};
-	};
-
 	pwm_leds {
 		compatible = "pwm-leds";

@@ -179,3 +91,87 @@
 			     &pinctrl_tcb1_tiob0>;
 	};
 };
+
+&tcb0 {
+	timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>, <1>;
+	};
+
+	timer@2 {
+		compatible = "atmel,tcb-timer";
+		reg = <2>;
+	};
+};
+
+&ebi {
+	status = "okay";
+};
+
+&nand_controller {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+	pinctrl-names = "default";
+
+	nand@3 {
+		reg = <0x3 0x0 0x800000>;
+		rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "soft";
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			ubi@20000 {
+				label = "ubi";
+				reg = <0x20000 0x7fe0000>;
+			};
+		};
+	};
+};
+
+&macb0 {
+	phy-mode = "mii";
+	pinctrl-0 = <&pinctrl_macb_rmii
+		     &pinctrl_macb_rmii_mii_alt>;
+	status = "okay";
+};
+
+&usart3 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&watchdog {
+	timeout-sec = <15>;
+	atmel,max-heartbeat-sec = <16>;
+	atmel,min-heartbeat-sec = <0>;
+	status = "okay";
+};
+
+&usb0 {
+	num-ports = <1>;
+	status = "okay";
+};
+
+&i2c-gpio-0 {
+	status = "okay";
+
+	rtc: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index dee9c0c8a096..9f9ee3cd7375 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -738,7 +738,7 @@
 				status = "disabled";
 			};

-			watchdog@fffffd40 {
+			watchdog: watchdog@fffffd40 {
 				compatible = "atmel,at91sam9260-wdt";
 				reg = <0xfffffd40 0x10>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
--
2.24.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2019-12-05 22:23 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-05 22:23 Kamel Bouhara [this message]
2019-12-05 22:23 ` [PATCH v2] ARM: dts: at91: rearrange kizbox dts using aliases nodes Kamel Bouhara

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191205222344.1367147-1-kamel.bouhara@bootlin.com \
    --to=kamel.bouhara@bootlin.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=ludovic.desroches@microchip.com \
    --cc=nicolas.ferre@microchip.com \
    --cc=robh+dt@kernel.org \
    --cc=thomas.petazzoni@bootlin.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.