From: Chen-Yu Tsai <wens@kernel.org> To: Maxime Ripard <mripard@kernel.org>, Mauro Carvalho Chehab <mchehab@kernel.org>, Sakari Ailus <sakari.ailus@linux.intel.com>, Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com> Cc: Chen-Yu Tsai <wens@kernel.org>, linux-media@vger.kernel.org, linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Chen-Yu Tsai <wens@csie.org> Subject: [PATCH 14/14] [DO NOT MERGE] ARM: dts: sun8i-r40: bananapi-m2-ultra: Enable OV5640 camera Date: Mon, 16 Dec 2019 00:59:24 +0800 [thread overview] Message-ID: <20191215165924.28314-15-wens@kernel.org> (raw) In-Reply-To: <20191215165924.28314-1-wens@kernel.org> From: Chen-Yu Tsai <wens@csie.org> Bananapi offers a small OV5640 based camera module, attached via an FPC connector. Add the related regulator constraints, and hook everything up. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- .../boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 67 +++++++++++++++++++ 1 file changed, 67 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts index 42d62d1ba1dc..86183d40c7af 100644 --- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts +++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts @@ -113,6 +113,24 @@ &ahci { status = "okay"; }; +&csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&csi0_8bits_pins>; + status = "okay"; + + port { + /* Parallel bus endpoint */ + csi0_from_ov5640: endpoint { + remote-endpoint = <&ov5640_to_csi0>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <1>; /* Active high */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; +}; + &de { status = "okay"; }; @@ -164,6 +182,37 @@ axp22x: pmic@34 { #include "axp22x.dtsi" +&i2c4 { + status = "okay"; + + ov5640: camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&csi0_mclk_pin>; + clocks = <&ccu CLK_CSI0_MCLK>; + clock-names = "xclk"; + + reset-gpios = <&pio 8 7 GPIO_ACTIVE_LOW>; /* PI7 */ + powerdown-gpios = <&pio 8 6 GPIO_ACTIVE_HIGH>; /* PI6 */ + AVDD-supply = <®_aldo1>; + DOVDD-supply = <®_eldo1>; + DVDD-supply = <®_eldo2>; + + port { + ov5640_to_csi0: endpoint { + remote-endpoint = <&csi0_from_ov5640>; + bus-width = <8>; + data-shift = <2>; + hsync-active = <1>; /* Active high */ + vsync-active = <1>; /* Active high */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; bus-width = <4>; @@ -209,6 +258,12 @@ &pio { vcc-pg-supply = <®_dldo1>; }; +®_aldo1 { + regulator-name = "csi-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + ®_aldo2 { regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; @@ -289,6 +344,18 @@ ®_dldo4 { regulator-name = "vdd2v5-sata"; }; +®_eldo1 { + regulator-name = "csi-iovcc"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +®_eldo2 { + regulator-name = "csi-dvdd"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; +}; + ®_eldo3 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; -- 2.24.0
WARNING: multiple messages have this Message-ID (diff)
From: Chen-Yu Tsai <wens@kernel.org> To: Maxime Ripard <mripard@kernel.org>, Mauro Carvalho Chehab <mchehab@kernel.org>, Sakari Ailus <sakari.ailus@linux.intel.com>, Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Chen-Yu Tsai <wens@csie.org>, Chen-Yu Tsai <wens@kernel.org>, linux-arm-kernel@lists.infradead.org, linux-media@vger.kernel.org Subject: [PATCH 14/14] [DO NOT MERGE] ARM: dts: sun8i-r40: bananapi-m2-ultra: Enable OV5640 camera Date: Mon, 16 Dec 2019 00:59:24 +0800 [thread overview] Message-ID: <20191215165924.28314-15-wens@kernel.org> (raw) In-Reply-To: <20191215165924.28314-1-wens@kernel.org> From: Chen-Yu Tsai <wens@csie.org> Bananapi offers a small OV5640 based camera module, attached via an FPC connector. Add the related regulator constraints, and hook everything up. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- .../boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 67 +++++++++++++++++++ 1 file changed, 67 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts index 42d62d1ba1dc..86183d40c7af 100644 --- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts +++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts @@ -113,6 +113,24 @@ &ahci { status = "okay"; }; +&csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&csi0_8bits_pins>; + status = "okay"; + + port { + /* Parallel bus endpoint */ + csi0_from_ov5640: endpoint { + remote-endpoint = <&ov5640_to_csi0>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <1>; /* Active high */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; +}; + &de { status = "okay"; }; @@ -164,6 +182,37 @@ axp22x: pmic@34 { #include "axp22x.dtsi" +&i2c4 { + status = "okay"; + + ov5640: camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&csi0_mclk_pin>; + clocks = <&ccu CLK_CSI0_MCLK>; + clock-names = "xclk"; + + reset-gpios = <&pio 8 7 GPIO_ACTIVE_LOW>; /* PI7 */ + powerdown-gpios = <&pio 8 6 GPIO_ACTIVE_HIGH>; /* PI6 */ + AVDD-supply = <®_aldo1>; + DOVDD-supply = <®_eldo1>; + DVDD-supply = <®_eldo2>; + + port { + ov5640_to_csi0: endpoint { + remote-endpoint = <&csi0_from_ov5640>; + bus-width = <8>; + data-shift = <2>; + hsync-active = <1>; /* Active high */ + vsync-active = <1>; /* Active high */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; bus-width = <4>; @@ -209,6 +258,12 @@ &pio { vcc-pg-supply = <®_dldo1>; }; +®_aldo1 { + regulator-name = "csi-avdd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + ®_aldo2 { regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; @@ -289,6 +344,18 @@ ®_dldo4 { regulator-name = "vdd2v5-sata"; }; +®_eldo1 { + regulator-name = "csi-iovcc"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +®_eldo2 { + regulator-name = "csi-dvdd"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; +}; + ®_eldo3 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; -- 2.24.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-12-15 17:00 UTC|newest] Thread overview: 68+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-12-15 16:59 [PATCH 00/14] media: sun4i-csi: A10/A20 CSI1 and R40 CSI0 support Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-15 16:59 ` [PATCH 01/14] dt-bindings: media: sun4i-csi: Add compatible for CSI1 on A10/A20 Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 10:30 ` Maxime Ripard 2019-12-16 10:30 ` Maxime Ripard 2019-12-19 23:56 ` Rob Herring 2019-12-19 23:56 ` Rob Herring 2019-12-15 16:59 ` [PATCH 02/14] dt-bindings: media: sun4i-csi: Add compatible for CSI0 on R40 Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 10:30 ` Maxime Ripard 2019-12-16 10:30 ` Maxime Ripard 2019-12-19 23:57 ` Rob Herring 2019-12-19 23:57 ` Rob Herring 2019-12-15 16:59 ` [PATCH 03/14] media: sun4i-csi: Fix data sampling polarity handling Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 13:36 ` Maxime Ripard 2019-12-16 13:36 ` Maxime Ripard 2019-12-15 16:59 ` [PATCH 04/14] media: sun4i-csi: Fix [HV]sync " Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 13:37 ` Maxime Ripard 2019-12-16 13:37 ` Maxime Ripard 2023-01-16 10:03 ` Oleg Verych 2023-01-16 10:03 ` Oleg Verych 2023-01-16 10:16 ` Maxime Ripard 2023-01-16 10:16 ` Maxime Ripard 2023-01-16 18:43 ` Oleg Verych 2023-01-16 18:43 ` Oleg Verych 2019-12-15 16:59 ` [PATCH 05/14] media: sun4i-csi: Deal with DRAM offset Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 13:38 ` Maxime Ripard 2019-12-16 13:38 ` Maxime Ripard 2019-12-15 16:59 ` [PATCH 06/14] media: sun4i-csi: Add support for A10 CSI1 camera sensor interface Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 13:38 ` Maxime Ripard 2019-12-16 13:38 ` Maxime Ripard 2020-01-02 11:33 ` Sakari Ailus 2020-01-02 11:33 ` Sakari Ailus 2020-01-02 11:36 ` Chen-Yu Tsai 2020-01-02 11:36 ` Chen-Yu Tsai 2019-12-15 16:59 ` [PATCH 07/14] ARM: dts: sun4i: Add CSI1 controller and pinmux options Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-15 16:59 ` [PATCH 08/14] ARM: dts: sun7i: " Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-15 16:59 ` [PATCH 09/14] ARM: dts: sun8i: r40: Add I2C " Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 10:29 ` Maxime Ripard 2019-12-16 10:29 ` Maxime Ripard 2019-12-15 16:59 ` [PATCH 10/14] dt-bindings: bus: sunxi: Add R40 MBUS compatible Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-19 23:58 ` Rob Herring 2019-12-19 23:58 ` Rob Herring 2019-12-15 16:59 ` [PATCH 11/14] ARM: dts: sun8i: r40: Add device node for CSI0 Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-16 13:39 ` Maxime Ripard 2019-12-16 13:39 ` Maxime Ripard 2019-12-16 13:42 ` Chen-Yu Tsai 2019-12-16 13:42 ` Chen-Yu Tsai 2019-12-16 13:53 ` Maxime Ripard 2019-12-16 13:53 ` Maxime Ripard 2019-12-15 16:59 ` [PATCH 12/14] [DO NOT MERGE] ARM: dts: sun4i: cubieboard: Enable OV7670 camera on CSI1 Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-15 16:59 ` [PATCH 13/14] [DO NOT MERGE] ARM: dts: sun7i: cubieboard2: " Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai 2019-12-15 16:59 ` Chen-Yu Tsai [this message] 2019-12-15 16:59 ` [PATCH 14/14] [DO NOT MERGE] ARM: dts: sun8i-r40: bananapi-m2-ultra: Enable OV5640 camera Chen-Yu Tsai 2020-01-01 10:20 ` [PATCH 00/14] media: sun4i-csi: A10/A20 CSI1 and R40 CSI0 support Chen-Yu Tsai 2020-01-01 10:20 ` Chen-Yu Tsai
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20191215165924.28314-15-wens@kernel.org \ --to=wens@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-media@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=mchehab@kernel.org \ --cc=mripard@kernel.org \ --cc=robh+dt@kernel.org \ --cc=sakari.ailus@linux.intel.com \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.