All of lore.kernel.org
 help / color / mirror / Atom feed
From: Douglas Anderson <dianders@chromium.org>
To: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Andy Gross <agross@kernel.org>
Cc: mturney@codeaurora.org, Jeffrey Hugo <jhugo@codeaurora.org>,
	rnayak@codeaurora.org, dhavalp@codeaurora.org,
	saiprakash.ranjan@codeaurora.org, sparate@codeaurora.org,
	linux-arm-msm@vger.kernel.org, mkurumel@codeaurora.org,
	Ravi Kumar Bokka <rbokka@codeaurora.org>,
	Douglas Anderson <dianders@chromium.org>,
	linux-kernel@vger.kernel.org
Subject: [PATCH v4 3/4] nvmem: qfprom: Add fuse blowing support
Date: Mon, 22 Jun 2020 07:49:28 -0700	[thread overview]
Message-ID: <20200622074845.v4.3.I68222d0b5966f652f29dd3a73ab33551a6e3b7e0@changeid> (raw)
In-Reply-To: <20200622144929.230498-1-dianders@chromium.org>

From: Ravi Kumar Bokka <rbokka@codeaurora.org>

This patch adds support for blowing fuses to the qfprom driver if the
required properties are defined in the device tree.

Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---

Changes in v4:
- Only get clock/regulator if all address ranges are provided.
- Don't use optional version of clk_get now.
- Clock name is "core", not "sec".
- Cleaned up error message if couldn't get clock.
- Fixed up minor version mask.
- Use GENMASK to generate masks.

Changes in v3:
- Don't provide "reset" value for things; just save/restore.
- Use the major/minor version read from 0x6000.
- Reading should still read "corrected", not "raw".
- Added a sysfs knob to allow you to read "raw" instead of "corrected"
- Simplified the SoC data structure.
- No need for quite so many levels of abstraction for clocks/regulator.
- Don't set regulator voltage.  Rely on device tree to make sure it's right.
- Properly undo things in the case of failure.
- Don't just keep enabling the regulator over and over again.
- Enable / disable the clock each time
- Polling every 100 us but timing out in 10 us didn't make sense; swap.
- No reason for 100 us to be SoC specific.
- No need for reg-names.
- We shouldn't be creating two separate nvmem devices.

 drivers/nvmem/qfprom.c | 314 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 303 insertions(+), 11 deletions(-)

diff --git a/drivers/nvmem/qfprom.c b/drivers/nvmem/qfprom.c
index 8a91717600be..0a8576f2d4c6 100644
--- a/drivers/nvmem/qfprom.c
+++ b/drivers/nvmem/qfprom.c
@@ -3,57 +3,349 @@
  * Copyright (C) 2015 Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
  */
 
+#include <linux/clk.h>
 #include <linux/device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/mod_devicetable.h>
-#include <linux/io.h>
 #include <linux/nvmem-provider.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+/* Blow timer clock frequency in Mhz */
+#define QFPROM_BLOW_TIMER_OFFSET 0x03c
+
+/* Amount of time required to hold charge to blow fuse in micro-seconds */
+#define QFPROM_FUSE_BLOW_POLL_US	10
+#define QFPROM_FUSE_BLOW_TIMEOUT_US	100
+
+#define QFPROM_BLOW_STATUS_OFFSET	0x048
+#define QFPROM_BLOW_STATUS_BUSY		0x1
+#define QFPROM_BLOW_STATUS_READY	0x0
+
+#define QFPROM_ACCEL_OFFSET		0x044
+
+#define QFPROM_VERSION_OFFSET		0x0
+#define QFPROM_MAJOR_VERSION_SHIFT	28
+#define QFPROM_MAJOR_VERSION_MASK	GENMASK(31, QFPROM_MAJOR_VERSION_SHIFT)
+#define QFPROM_MINOR_VERSION_SHIFT	16
+#define QFPROM_MINOR_VERSION_MASK	GENMASK(27, QFPROM_MINOR_VERSION_SHIFT)
+
+static bool read_raw_data;
+module_param(read_raw_data, bool, 0644);
+MODULE_PARM_DESC(read_raw_data, "Read raw instead of corrected data");
 
+/**
+ * struct qfprom_soc_data - config that varies from SoC to SoC.
+ *
+ * @accel_value:             Should contain qfprom accel value.
+ * @qfprom_blow_timer_value: The timer value of qfprom when doing efuse blow.
+ * @qfprom_blow_set_freq:    The frequency required to set when we start the
+ *                           fuse blowing.
+ */
+struct qfprom_soc_data {
+	u32 accel_value;
+	u32 qfprom_blow_timer_value;
+	u32 qfprom_blow_set_freq;
+};
+
+/**
+ * struct qfprom_priv - structure holding qfprom attributes
+ *
+ * @qfpraw:       iomapped memory space for qfprom-efuse raw address space.
+ * @qfpconf:      iomapped memory space for qfprom-efuse configuration address
+ *                space.
+ * @qfpcorrected: iomapped memory space for qfprom corrected address space.
+ * @qfpsecurity:  iomapped memory space for qfprom security control space.
+ * @dev:          qfprom device structure.
+ * @secclk:       Clock supply.
+ * @vcc:          Regulator supply.
+ * @soc_data:     Data that for things that varies from SoC to SoC.
+ */
 struct qfprom_priv {
-	void __iomem *base;
+	void __iomem *qfpraw;
+	void __iomem *qfpconf;
+	void __iomem *qfpcorrected;
+	void __iomem *qfpsecurity;
+	struct device *dev;
+	struct clk *secclk;
+	struct regulator *vcc;
+	const struct qfprom_soc_data *soc_data;
+};
+
+/**
+ * struct qfprom_touched_values - saved values to restore after blowing
+ *
+ * @clk_rate: The rate the clock was at before blowing.
+ * @accel_val: The value of the accel reg before blowing.
+ * @timer_val: The value of the timer before blowing.
+ */
+struct qfprom_touched_values {
+	unsigned long clk_rate;
+	u32 accel_val;
+	u32 timer_val;
 };
 
+/**
+ * qfprom_disable_fuse_blowing() - Undo enabling of fuse blowing.
+ * @priv: Our driver data.
+ * @old:  The data that was stashed from before fuse blowing.
+ *
+ * Resets the value of the blow timer, accel register and the clock
+ * and voltage settings.
+ *
+ * Prints messages if there are errors but doesn't return an error code
+ * since there's not much we can do upon failure.
+ */
+static void qfprom_disable_fuse_blowing(const struct qfprom_priv *priv,
+					const struct qfprom_touched_values *old)
+{
+	int ret;
+
+	ret = regulator_disable(priv->vcc);
+	if (ret)
+		dev_warn(priv->dev, "Failed to disable regulator (ignoring)\n");
+
+	ret = clk_set_rate(priv->secclk, old->clk_rate);
+	if (ret)
+		dev_warn(priv->dev,
+			 "Failed to set clock rate for disable (ignoring)\n");
+
+	clk_disable_unprepare(priv->secclk);
+
+	writel(old->timer_val, priv->qfpconf + QFPROM_BLOW_TIMER_OFFSET);
+	writel(old->accel_val, priv->qfpconf + QFPROM_ACCEL_OFFSET);
+}
+
+/**
+ * qfprom_enable_fuse_blowing() - Enable fuse blowing.
+ * @priv: Our driver data.
+ * @old:  We'll stash stuff here to use when disabling.
+ *
+ * Sets the value of the blow timer, accel register and the clock
+ * and voltage settings.
+ *
+ * Prints messages if there are errors so caller doesn't need to.
+ *
+ * Return: 0 or -err.
+ */
+static int qfprom_enable_fuse_blowing(const struct qfprom_priv *priv,
+				      struct qfprom_touched_values *old)
+{
+	int ret;
+
+	ret = clk_prepare_enable(priv->secclk);
+	if (ret) {
+		dev_err(priv->dev, "Failed to enable clock\n");
+		return ret;
+	}
+
+	old->clk_rate = clk_get_rate(priv->secclk);
+	ret = clk_set_rate(priv->secclk, priv->soc_data->qfprom_blow_set_freq);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set clock rate for enable\n");
+		goto err_clk_prepared;
+	}
+
+	ret = regulator_enable(priv->vcc);
+	if (ret) {
+		dev_err(priv->dev, "Failed to enable regulator\n");
+		goto err_clk_rate_set;
+	}
+
+	old->timer_val = readl(priv->qfpconf + QFPROM_BLOW_TIMER_OFFSET);
+	old->accel_val = readl(priv->qfpconf + QFPROM_ACCEL_OFFSET);
+	writel(priv->soc_data->qfprom_blow_timer_value,
+	       priv->qfpconf + QFPROM_BLOW_TIMER_OFFSET);
+	writel(priv->soc_data->accel_value,
+	       priv->qfpconf + QFPROM_ACCEL_OFFSET);
+
+	return 0;
+
+err_clk_rate_set:
+	clk_set_rate(priv->secclk, old->clk_rate);
+err_clk_prepared:
+	clk_disable_unprepare(priv->secclk);
+	return ret;
+}
+
+/**
+ * qfprom_efuse_reg_write() - Write to fuses.
+ * @context: Our driver data.
+ * @reg:     The offset to write at.
+ * @_val:    Pointer to data to write.
+ * @bytes:   The number of bytes to write.
+ *
+ * Writes to fuses.  WARNING: THIS IS PERMANENT.
+ *
+ * Return: 0 or -err.
+ */
+static int qfprom_reg_write(void *context, unsigned int reg, void *_val,
+			    size_t bytes)
+{
+	struct qfprom_priv *priv = context;
+	struct qfprom_touched_values old;
+	int words = bytes / 4;
+	u32 *value = _val;
+	u32 blow_status;
+	int ret;
+	int i;
+
+	dev_dbg(priv->dev,
+		"Writing to raw qfprom region : %#010x of size: %zu\n",
+		reg, bytes);
+
+	/*
+	 * The hardware only allows us to write word at a time, but we can
+	 * read byte at a time.  Until the nvmem framework allows a separate
+	 * word_size and stride for reading vs. writing, we'll enforce here.
+	 */
+	if (bytes % 4) {
+		dev_err(priv->dev,
+			"%zu is not an integral number of words\n", bytes);
+		return -EINVAL;
+	}
+	if (reg % 4) {
+		dev_err(priv->dev,
+			"Invalid offset: %#x.  Must be word aligned\n", reg);
+		return -EINVAL;
+	}
+
+	ret = qfprom_enable_fuse_blowing(priv, &old);
+	if (ret)
+		return ret;
+
+	ret = readl_relaxed_poll_timeout(
+		priv->qfpconf + QFPROM_BLOW_STATUS_OFFSET,
+		blow_status, blow_status == QFPROM_BLOW_STATUS_READY,
+		QFPROM_FUSE_BLOW_POLL_US, QFPROM_FUSE_BLOW_TIMEOUT_US);
+
+	if (ret) {
+		dev_err(priv->dev,
+			"Timeout waiting for initial ready; aborting.\n");
+		goto exit_enabled_fuse_blowing;
+	}
+
+	for (i = 0; i < words; i++)
+		writel(value[i], priv->qfpraw + reg + (i * 4));
+
+	ret = readl_relaxed_poll_timeout(
+		priv->qfpconf + QFPROM_BLOW_STATUS_OFFSET,
+		blow_status, blow_status == QFPROM_BLOW_STATUS_READY,
+		QFPROM_FUSE_BLOW_POLL_US, QFPROM_FUSE_BLOW_TIMEOUT_US);
+
+	/* Give an error, but not much we can do in this case */
+	if (ret)
+		dev_err(priv->dev, "Timeout waiting for finish.\n");
+
+exit_enabled_fuse_blowing:
+	qfprom_disable_fuse_blowing(priv, &old);
+
+	return ret;
+}
+
 static int qfprom_reg_read(void *context,
 			unsigned int reg, void *_val, size_t bytes)
 {
 	struct qfprom_priv *priv = context;
 	u8 *val = _val;
 	int i = 0, words = bytes;
+	void __iomem *base = priv->qfpcorrected;
+
+	if (read_raw_data && priv->qfpraw)
+		base = priv->qfpraw;
 
 	while (words--)
-		*val++ = readb(priv->base + reg + i++);
+		*val++ = readb(base + reg + i++);
 
 	return 0;
 }
 
-static struct nvmem_config econfig = {
-	.name = "qfprom",
-	.stride = 1,
-	.word_size = 1,
-	.reg_read = qfprom_reg_read,
+static const struct qfprom_soc_data qfprom_7_8_data = {
+	.accel_value = 0xD10,
+	.qfprom_blow_timer_value = 25,
+	.qfprom_blow_set_freq = 4800000,
 };
 
 static int qfprom_probe(struct platform_device *pdev)
 {
+	struct nvmem_config econfig = {
+		.name = "qfprom",
+		.stride = 1,
+		.word_size = 1,
+		.reg_read = qfprom_reg_read,
+	};
 	struct device *dev = &pdev->dev;
 	struct resource *res;
 	struct nvmem_device *nvmem;
 	struct qfprom_priv *priv;
+	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
 
+	/* The corrected section is always provided */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(priv->base))
-		return PTR_ERR(priv->base);
+	priv->qfpcorrected = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->qfpcorrected))
+		return PTR_ERR(priv->qfpcorrected);
 
 	econfig.size = resource_size(res);
 	econfig.dev = dev;
 	econfig.priv = priv;
 
+	priv->dev = dev;
+
+	/*
+	 * If more than one region is provided then the OS has the ability
+	 * to write.
+	 */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (res) {
+		u32 version;
+		int major_version, minor_version;
+
+		priv->qfpraw = devm_ioremap_resource(dev, res);
+		if (IS_ERR(priv->qfpraw))
+			return PTR_ERR(priv->qfpraw);
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+		priv->qfpconf = devm_ioremap_resource(dev, res);
+		if (IS_ERR(priv->qfpconf))
+			return PTR_ERR(priv->qfpconf);
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
+		priv->qfpsecurity = devm_ioremap_resource(dev, res);
+		if (IS_ERR(priv->qfpsecurity))
+			return PTR_ERR(priv->qfpsecurity);
+
+		version = readl(priv->qfpsecurity + QFPROM_VERSION_OFFSET);
+		major_version = (version & QFPROM_MAJOR_VERSION_MASK) >>
+				QFPROM_MAJOR_VERSION_SHIFT;
+		minor_version = (version & QFPROM_MINOR_VERSION_MASK) >>
+				QFPROM_MINOR_VERSION_SHIFT;
+
+		if (major_version == 7 && minor_version == 8)
+			priv->soc_data = &qfprom_7_8_data;
+
+		priv->vcc = devm_regulator_get(&pdev->dev, "vcc");
+		if (IS_ERR(priv->vcc))
+			return PTR_ERR(priv->vcc);
+
+		priv->secclk = devm_clk_get(dev, "core");
+		if (IS_ERR(priv->secclk)) {
+			ret = PTR_ERR(priv->secclk);
+			if (ret != -EPROBE_DEFER)
+				dev_err(dev, "Error getting clock: %d\n", ret);
+			return ret;
+		}
+
+		/* Only enable writing if we have SoC data. */
+		if (priv->soc_data)
+			econfig.reg_write = qfprom_reg_write;
+	}
+
 	nvmem = devm_nvmem_register(dev, &econfig);
 
 	return PTR_ERR_OR_ZERO(nvmem);
-- 
2.27.0.111.gc72c7da667-goog


  parent reply	other threads:[~2020-06-22 14:49 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-06-22 14:49 [PATCH v4 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
2020-06-22 14:49 ` [PATCH v4 1/4] dt-bindings: nvmem: qfprom: Convert to yaml Douglas Anderson
2020-07-09 23:16   ` Rob Herring
2020-06-22 14:49 ` [PATCH v4 2/4] dt-bindings: nvmem: Add properties needed for blowing fuses Douglas Anderson
2020-07-09 23:16   ` Rob Herring
2020-06-22 14:49 ` Douglas Anderson [this message]
2020-07-01 15:09   ` [PATCH v4 3/4] nvmem: qfprom: Add fuse blowing support Ravi Kumar Bokka (Temp)
2020-07-01 15:13     ` Doug Anderson
2020-07-07 14:52   ` Doug Anderson
2020-07-07 14:54     ` Srinivas Kandagatla
2020-06-22 14:49 ` [PATCH v4 4/4] arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing Douglas Anderson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200622074845.v4.3.I68222d0b5966f652f29dd3a73ab33551a6e3b7e0@changeid \
    --to=dianders@chromium.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=dhavalp@codeaurora.org \
    --cc=jhugo@codeaurora.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mkurumel@codeaurora.org \
    --cc=mturney@codeaurora.org \
    --cc=rbokka@codeaurora.org \
    --cc=rnayak@codeaurora.org \
    --cc=robh+dt@kernel.org \
    --cc=saiprakash.ranjan@codeaurora.org \
    --cc=sparate@codeaurora.org \
    --cc=srinivas.kandagatla@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.