From: Jagan Teki <jagan@amarulasolutions.com> To: Kever Yang <kever.yang@rock-chips.com>, Philipp Tomsich <philipp.tomsich@theobroma-systems.com>, Simon Glass <sjg@chromium.org> Cc: Suniel Mahesh <sunil@amarulasolutions.com>, U-Boot-Denx <u-boot@lists.denx.de>, linux-rockchip@lists.infradead.org, linux-amarula <linux-amarula@amarulasolutions.com>, Jagan Teki <jagan@amarulasolutions.com>, Tom Cubie <tom@radxa.com> Subject: [PATCH v2 6/7] ARM: dts: rockchip: Add VMARC RK3288 SOM initial support Date: Wed, 8 Jul 2020 15:35:27 +0530 [thread overview] Message-ID: <20200708100528.419035-7-jagan@amarulasolutions.com> (raw) In-Reply-To: <20200708100528.419035-1-jagan@amarulasolutions.com> VMARC RK3288 SOM is a standard SMARC SOM design with Rockchip RK3288 SoC, which is designed by Vamrs. Specification: - Rockchip RK3288 - PMIC: RK808 - eMMC: 16GB/32GB/64GB - SD slot - 2xUSB-2.0, 1xUSB3.0 - USB-C for power supply - Ethernet - HDMI, MIPI-DSI/CSI, eDP Add initial support for VMARC RK3288 SOM, this would use with associated carrier board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- arch/arm/dts/rk3288-vmarc-som.dtsi | 270 +++++++++++++++++++++++++++++ 1 file changed, 270 insertions(+) create mode 100644 arch/arm/dts/rk3288-vmarc-som.dtsi diff --git a/arch/arm/dts/rk3288-vmarc-som.dtsi b/arch/arm/dts/rk3288-vmarc-som.dtsi new file mode 100644 index 0000000000..0bcb9f067d --- /dev/null +++ b/arch/arm/dts/rk3288-vmarc-som.dtsi @@ -0,0 +1,270 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Vamrs Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/rockchip.h> + +/ { + compatible = "vamrs,rk3288-vmarc-som", "rockchip,rk3288"; + + vccio_flash: vccio-flash-regulator { + compatible = "regulator-fixed"; + regulator-name = "vccio_flash"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_io>; + }; +}; + +&emmc { + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; + vmmc-supply = <&vcc_io>; + vqmmc-supply = <&vccio_flash>; + status = "okay"; +}; + +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + phy-supply = <&vcc_io>; + snps,reset-gpio = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + rk808: pmic@1b { + compatible = "rockchip,rk808"; + reg = <0x1b>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int &global_pwroff>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + + vcc1-supply = <&vcc5v0_sys>; + vcc2-supply = <&vcc5v0_sys>; + vcc3-supply = <&vcc5v0_sys>; + vcc4-supply = <&vcc5v0_sys>; + vcc6-supply = <&vcc5v0_sys>; + vcc7-supply = <&vcc5v0_sys>; + vcc8-supply = <&vcc_io>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc5v0_sys>; + vcc11-supply = <&vcc5v0_sys>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vcc_io>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd_arm"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + regulator-ramp-delay = <6000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_tp: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_tp"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca_codec: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_wl: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_wl"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc18_lcd: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_sd: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&io_domains { + bb-supply = <&vcc_io>; + flash0-supply = <&vccio_flash>; + gpio1830-supply = <&vcc_18>; + gpio30-supply = <&vcc_io>; + sdcard-supply = <&vccio_sd>; + status = "okay"; +}; + +&pinctrl { + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma { + drive-strength = <8>; + }; + + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma { + bias-pull-up; + drive-strength = <8>; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + sdmmc { + sdmmc_bus4: sdmmc-bus4 { + rockchip,pins = + <6 RK_PC0 1 &pcfg_pull_up_drv_8ma>, + <6 RK_PC1 1 &pcfg_pull_up_drv_8ma>, + <6 RK_PC2 1 &pcfg_pull_up_drv_8ma>, + <6 RK_PC3 1 &pcfg_pull_up_drv_8ma>; + }; + + sdmmc_clk: sdmmc-clk { + rockchip,pins = <6 RK_PC4 1 &pcfg_pull_none_drv_8ma>; + }; + + sdmmc_cmd: sdmmc-cmd { + rockchip,pins = <6 RK_PC5 1 &pcfg_pull_up_drv_8ma>; + }; + }; +}; -- 2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Jagan Teki <jagan@amarulasolutions.com> To: u-boot@lists.denx.de Subject: [PATCH v2 6/7] ARM: dts: rockchip: Add VMARC RK3288 SOM initial support Date: Wed, 8 Jul 2020 15:35:27 +0530 [thread overview] Message-ID: <20200708100528.419035-7-jagan@amarulasolutions.com> (raw) In-Reply-To: <20200708100528.419035-1-jagan@amarulasolutions.com> VMARC RK3288 SOM is a standard SMARC SOM design with Rockchip RK3288 SoC, which is designed by Vamrs. Specification: - Rockchip RK3288 - PMIC: RK808 - eMMC: 16GB/32GB/64GB - SD slot - 2xUSB-2.0, 1xUSB3.0 - USB-C for power supply - Ethernet - HDMI, MIPI-DSI/CSI, eDP Add initial support for VMARC RK3288 SOM, this would use with associated carrier board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- arch/arm/dts/rk3288-vmarc-som.dtsi | 270 +++++++++++++++++++++++++++++ 1 file changed, 270 insertions(+) create mode 100644 arch/arm/dts/rk3288-vmarc-som.dtsi diff --git a/arch/arm/dts/rk3288-vmarc-som.dtsi b/arch/arm/dts/rk3288-vmarc-som.dtsi new file mode 100644 index 0000000000..0bcb9f067d --- /dev/null +++ b/arch/arm/dts/rk3288-vmarc-som.dtsi @@ -0,0 +1,270 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd + * Copyright (c) 2019 Vamrs Limited + * Copyright (c) 2019 Amarula Solutions(India) + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/rockchip.h> + +/ { + compatible = "vamrs,rk3288-vmarc-som", "rockchip,rk3288"; + + vccio_flash: vccio-flash-regulator { + compatible = "regulator-fixed"; + regulator-name = "vccio_flash"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_io>; + }; +}; + +&emmc { + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; + vmmc-supply = <&vcc_io>; + vqmmc-supply = <&vccio_flash>; + status = "okay"; +}; + +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + phy-supply = <&vcc_io>; + snps,reset-gpio = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + rk808: pmic at 1b { + compatible = "rockchip,rk808"; + reg = <0x1b>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int &global_pwroff>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + + vcc1-supply = <&vcc5v0_sys>; + vcc2-supply = <&vcc5v0_sys>; + vcc3-supply = <&vcc5v0_sys>; + vcc4-supply = <&vcc5v0_sys>; + vcc6-supply = <&vcc5v0_sys>; + vcc7-supply = <&vcc5v0_sys>; + vcc8-supply = <&vcc_io>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc5v0_sys>; + vcc11-supply = <&vcc5v0_sys>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vcc_io>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd_arm"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + regulator-ramp-delay = <6000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_tp: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_tp"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca_codec: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_wl: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_wl"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc18_lcd: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_sd: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&io_domains { + bb-supply = <&vcc_io>; + flash0-supply = <&vccio_flash>; + gpio1830-supply = <&vcc_18>; + gpio30-supply = <&vcc_io>; + sdcard-supply = <&vccio_sd>; + status = "okay"; +}; + +&pinctrl { + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma { + drive-strength = <8>; + }; + + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma { + bias-pull-up; + drive-strength = <8>; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + sdmmc { + sdmmc_bus4: sdmmc-bus4 { + rockchip,pins = + <6 RK_PC0 1 &pcfg_pull_up_drv_8ma>, + <6 RK_PC1 1 &pcfg_pull_up_drv_8ma>, + <6 RK_PC2 1 &pcfg_pull_up_drv_8ma>, + <6 RK_PC3 1 &pcfg_pull_up_drv_8ma>; + }; + + sdmmc_clk: sdmmc-clk { + rockchip,pins = <6 RK_PC4 1 &pcfg_pull_none_drv_8ma>; + }; + + sdmmc_cmd: sdmmc-cmd { + rockchip,pins = <6 RK_PC5 1 &pcfg_pull_up_drv_8ma>; + }; + }; +}; -- 2.25.1
next prev parent reply other threads:[~2020-07-08 10:05 UTC|newest] Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-07-08 10:05 [PATCH v2 0/7] rockchip: Add RockPI N8/N10 support Jagan Teki 2020-07-08 10:05 ` Jagan Teki 2020-07-08 10:05 ` [PATCH v2 1/7] arm64: dts: rockchip: Sync v5.7-rc1 rk3399pro.dtsi Jagan Teki 2020-07-08 10:05 ` Jagan Teki 2020-07-08 10:05 ` [PATCH v2 2/7] arm64: dts: rockchip: Sync v5.7-rc1 VMARC RK3399Pro SOM Jagan Teki 2020-07-08 10:05 ` Jagan Teki 2020-07-08 10:05 ` [PATCH v2 3/7] ARM: dts: rockchip: Sync v5.7-rc1 Radxa Dalang Carrier Jagan Teki 2020-07-08 10:05 ` Jagan Teki 2020-07-08 10:05 ` [PATCH v2 4/7] arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support Jagan Teki 2020-07-08 10:05 ` Jagan Teki 2020-07-08 10:05 ` [PATCH v2 5/7] arm64: dts: rockchip: Trivial cleanups for RockPI N10 Jagan Teki 2020-07-08 10:05 ` Jagan Teki 2020-07-08 10:05 ` Jagan Teki [this message] 2020-07-08 10:05 ` [PATCH v2 6/7] ARM: dts: rockchip: Add VMARC RK3288 SOM initial support Jagan Teki 2020-07-08 10:05 ` [PATCH v2 7/7] ARM: dts: rockchip: Add Radxa Rock Pi N8 " Jagan Teki 2020-07-08 10:05 ` Jagan Teki
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20200708100528.419035-7-jagan@amarulasolutions.com \ --to=jagan@amarulasolutions.com \ --cc=kever.yang@rock-chips.com \ --cc=linux-amarula@amarulasolutions.com \ --cc=linux-rockchip@lists.infradead.org \ --cc=philipp.tomsich@theobroma-systems.com \ --cc=sjg@chromium.org \ --cc=sunil@amarulasolutions.com \ --cc=tom@radxa.com \ --cc=u-boot@lists.denx.de \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.