From: andy.tang@nxp.com To: shawnguo@kernel.org Cc: amit.kucheria@linaro.org, leoyang.li@nxp.com, robh+dt@kernel.org, linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Yuantian Tang <andy.tang@nxp.com> Subject: [PATCH 2/2 v2] arm64: dts: ls208xa: add more thermal zone support Date: Wed, 15 Jul 2020 14:49:09 +0800 [thread overview] Message-ID: <20200715064909.9161-2-andy.tang@nxp.com> (raw) In-Reply-To: <20200715064909.9161-1-andy.tang@nxp.com> From: Yuantian Tang <andy.tang@nxp.com> There are 7 thermal zones in ls208xa soc. Add the other thermal zone nodes to enable them. Signed-off-by: Yuantian Tang <andy.tang@nxp.com> --- v2: - remove useless alert trip - add cooling-map to core cluster zones. .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 141 ++++++++++++++++-- 1 file changed, 132 insertions(+), 9 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi index 41102dacc2e1..cc36c969dd9d 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi @@ -79,20 +79,62 @@ }; thermal-zones { - cpu_thermal: cpu-thermal { + ddr-controller1 { polling-delay-passive = <1000>; polling-delay = <5000>; + thermal-sensors = <&tmu 1>; + trips { + ddr-ctrler1-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + ddr-controller2 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 2>; + + trips { + ddr-ctrler2-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + ddr-controller3 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 3>; + + trips { + ddr-ctrler3-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + core-cluster1 { + polling-delay-passive = <1000>; + polling-delay = <5000>; thermal-sensors = <&tmu 4>; trips { - cpu_alert: cpu-alert { - temperature = <75000>; + core_cluster1_alert: core-cluster1-alert { + temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - cpu_crit: cpu-crit { - temperature = <85000>; + + core-cluster1-crit { + temperature = <95000>; hysteresis = <2000>; type = "critical"; }; @@ -100,14 +142,95 @@ cooling-maps { map0 { - trip = <&cpu_alert>; + trip = <&core_cluster1_alert>; cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + core-cluster2 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 5>; + + trips { + core_cluster2_alert: core-cluster2-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core-cluster2-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster2_alert>; + cooling-device = <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + core-cluster3 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 6>; + + trips { + core_cluster3_alert: core-cluster3-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core-cluster3-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster3_alert>; + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + core-cluster4 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 7>; + + trips { + core_cluster4_alert: core-cluster4-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core-cluster4-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster4_alert>; + cooling-device = <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: andy.tang@nxp.com To: shawnguo@kernel.org Cc: devicetree@vger.kernel.org, Yuantian Tang <andy.tang@nxp.com>, linux-kernel@vger.kernel.org, amit.kucheria@linaro.org, leoyang.li@nxp.com, robh+dt@kernel.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH 2/2 v2] arm64: dts: ls208xa: add more thermal zone support Date: Wed, 15 Jul 2020 14:49:09 +0800 [thread overview] Message-ID: <20200715064909.9161-2-andy.tang@nxp.com> (raw) In-Reply-To: <20200715064909.9161-1-andy.tang@nxp.com> From: Yuantian Tang <andy.tang@nxp.com> There are 7 thermal zones in ls208xa soc. Add the other thermal zone nodes to enable them. Signed-off-by: Yuantian Tang <andy.tang@nxp.com> --- v2: - remove useless alert trip - add cooling-map to core cluster zones. .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 141 ++++++++++++++++-- 1 file changed, 132 insertions(+), 9 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi index 41102dacc2e1..cc36c969dd9d 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi @@ -79,20 +79,62 @@ }; thermal-zones { - cpu_thermal: cpu-thermal { + ddr-controller1 { polling-delay-passive = <1000>; polling-delay = <5000>; + thermal-sensors = <&tmu 1>; + trips { + ddr-ctrler1-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + ddr-controller2 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 2>; + + trips { + ddr-ctrler2-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + ddr-controller3 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 3>; + + trips { + ddr-ctrler3-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + core-cluster1 { + polling-delay-passive = <1000>; + polling-delay = <5000>; thermal-sensors = <&tmu 4>; trips { - cpu_alert: cpu-alert { - temperature = <75000>; + core_cluster1_alert: core-cluster1-alert { + temperature = <85000>; hysteresis = <2000>; type = "passive"; }; - cpu_crit: cpu-crit { - temperature = <85000>; + + core-cluster1-crit { + temperature = <95000>; hysteresis = <2000>; type = "critical"; }; @@ -100,14 +142,95 @@ cooling-maps { map0 { - trip = <&cpu_alert>; + trip = <&core_cluster1_alert>; cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + core-cluster2 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 5>; + + trips { + core_cluster2_alert: core-cluster2-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core-cluster2-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster2_alert>; + cooling-device = <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + core-cluster3 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 6>; + + trips { + core_cluster3_alert: core-cluster3-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core-cluster3-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster3_alert>; + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + core-cluster4 { + polling-delay-passive = <1000>; + polling-delay = <5000>; + thermal-sensors = <&tmu 7>; + + trips { + core_cluster4_alert: core-cluster4-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + core-cluster4-crit { + temperature = <95000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&core_cluster4_alert>; + cooling-device = <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-07-15 6:55 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-07-15 6:49 [PATCH 1/2 v2] arm64: dts: ls1088a: add more thermal zone support andy.tang 2020-07-15 6:49 ` andy.tang 2020-07-15 6:49 ` andy.tang [this message] 2020-07-15 6:49 ` [PATCH 2/2 v2] arm64: dts: ls208xa: " andy.tang 2020-08-21 6:09 ` Amit Kucheria 2020-08-21 6:09 ` Amit Kucheria 2020-08-17 8:02 ` [PATCH 1/2 v2] arm64: dts: ls1088a: " Shawn Guo 2020-08-17 8:02 ` Shawn Guo 2020-08-21 6:09 ` Amit Kucheria 2020-08-21 6:09 ` Amit Kucheria 2020-08-22 3:29 ` Shawn Guo 2020-08-22 3:29 ` Shawn Guo
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20200715064909.9161-2-andy.tang@nxp.com \ --to=andy.tang@nxp.com \ --cc=amit.kucheria@linaro.org \ --cc=devicetree@vger.kernel.org \ --cc=leoyang.li@nxp.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=shawnguo@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.