From: Roger Quadros <rogerq@ti.com>
To: <kishon@ti.com>, <vkoul@kernel.org>
Cc: <nsekhar@ti.com>, <vigneshr@ti.com>, <jan.kiszka@siemens.com>,
<linux-kernel@vger.kernel.org>, Roger Quadros <rogerq@ti.com>
Subject: [PATCH v6 1/2] phy: omap-usb2-phy: disable PHY charger detect
Date: Mon, 24 Aug 2020 10:51:26 +0300 [thread overview]
Message-ID: <20200824075127.14902-2-rogerq@ti.com> (raw)
In-Reply-To: <20200824075127.14902-1-rogerq@ti.com>
AM654x PG1.0 has a silicon bug that D+ is pulled high after POR, which
could cause enumeration failure with some USB hubs. Disabling the
USB2_PHY Charger Detect function will put D+ into the normal state.
This addresses Silicon Errata:
i2075 - "USB2PHY: USB2PHY Charger Detect is Enabled by Default Without VBUS
Presence"
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
---
drivers/phy/ti/phy-omap-usb2.c | 47 +++++++++++++++++++++++++++++-----
1 file changed, 40 insertions(+), 7 deletions(-)
diff --git a/drivers/phy/ti/phy-omap-usb2.c b/drivers/phy/ti/phy-omap-usb2.c
index cb2dd3230fa7..507f79d14adb 100644
--- a/drivers/phy/ti/phy-omap-usb2.c
+++ b/drivers/phy/ti/phy-omap-usb2.c
@@ -22,10 +22,15 @@
#include <linux/mfd/syscon.h>
#include <linux/regmap.h>
#include <linux/of_platform.h>
+#include <linux/sys_soc.h>
#define USB2PHY_ANA_CONFIG1 0x4c
#define USB2PHY_DISCON_BYP_LATCH BIT(31)
+#define USB2PHY_CHRG_DET 0x14
+#define USB2PHY_CHRG_DET_USE_CHG_DET_REG BIT(29)
+#define USB2PHY_CHRG_DET_DIS_CHG_DET BIT(28)
+
/* SoC Specific USB2_OTG register definitions */
#define AM654_USB2_OTG_PD BIT(8)
#define AM654_USB2_VBUS_DET_EN BIT(5)
@@ -43,6 +48,7 @@
#define OMAP_USB2_HAS_START_SRP BIT(0)
#define OMAP_USB2_HAS_SET_VBUS BIT(1)
#define OMAP_USB2_CALIBRATE_FALSE_DISCONNECT BIT(2)
+#define OMAP_USB2_DISABLE_CHRG_DET BIT(3)
struct omap_usb {
struct usb_phy phy;
@@ -236,6 +242,13 @@ static int omap_usb_init(struct phy *x)
omap_usb_writel(phy->phy_base, USB2PHY_ANA_CONFIG1, val);
}
+ if (phy->flags & OMAP_USB2_DISABLE_CHRG_DET) {
+ val = omap_usb_readl(phy->phy_base, USB2PHY_CHRG_DET);
+ val |= USB2PHY_CHRG_DET_USE_CHG_DET_REG |
+ USB2PHY_CHRG_DET_DIS_CHG_DET;
+ omap_usb_writel(phy->phy_base, USB2PHY_CHRG_DET, val);
+ }
+
return 0;
}
@@ -329,6 +342,26 @@ static const struct of_device_id omap_usb2_id_table[] = {
};
MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
+static void omap_usb2_init_errata(struct omap_usb *phy)
+{
+ static const struct soc_device_attribute am65x_sr10_soc_devices[] = {
+ { .family = "AM65X", .revision = "SR1.0" },
+ { /* sentinel */ }
+ };
+
+ /*
+ * Errata i2075: USB2PHY: USB2PHY Charger Detect is Enabled by
+ * Default Without VBUS Presence.
+ *
+ * AM654x SR1.0 has a silicon bug due to which D+ is pulled high after
+ * POR, which could cause enumeration failure with some USB hubs.
+ * Disabling the USB2_PHY Charger Detect function will put D+
+ * into the normal state.
+ */
+ if (soc_device_match(am65x_sr10_soc_devices))
+ phy->flags |= OMAP_USB2_DISABLE_CHRG_DET;
+}
+
static int omap_usb2_probe(struct platform_device *pdev)
{
struct omap_usb *phy;
@@ -366,14 +399,14 @@ static int omap_usb2_probe(struct platform_device *pdev)
phy->mask = phy_data->mask;
phy->power_on = phy_data->power_on;
phy->power_off = phy_data->power_off;
+ phy->flags = phy_data->flags;
- if (phy_data->flags & OMAP_USB2_CALIBRATE_FALSE_DISCONNECT) {
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- phy->phy_base = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(phy->phy_base))
- return PTR_ERR(phy->phy_base);
- phy->flags |= OMAP_USB2_CALIBRATE_FALSE_DISCONNECT;
- }
+ omap_usb2_init_errata(phy);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy->phy_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(phy->phy_base))
+ return PTR_ERR(phy->phy_base);
phy->syscon_phy_power = syscon_regmap_lookup_by_phandle(node,
"syscon-phy-power");
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
next prev parent reply other threads:[~2020-08-24 7:51 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-08-24 7:51 [PATCH v6 0/2] phy: omap-usb2-phy: Errata and coding style fix Roger Quadros
2020-08-24 7:51 ` Roger Quadros [this message]
2020-08-24 7:51 ` [PATCH v6 2/2] phy: omap-usb2-phy: fix coding style issues Roger Quadros
2020-08-31 9:01 ` [PATCH v6 0/2] phy: omap-usb2-phy: Errata and coding style fix Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200824075127.14902-2-rogerq@ti.com \
--to=rogerq@ti.com \
--cc=jan.kiszka@siemens.com \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=nsekhar@ti.com \
--cc=vigneshr@ti.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.