All of lore.kernel.org
 help / color / mirror / Atom feed
From: Serge Semin <Sergey.Semin@baikalelectronics.ru>
To: Mark Brown <broonie@kernel.org>, Serge Semin <fancer.lancer@gmail.com>
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>,
	Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>,
	Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>,
	Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>,
	Andy Shevchenko <andy.shevchenko@gmail.com>,
	Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
	Lars Povlsen <lars.povlsen@microchip.com>,
	"wuxu . wu" <wuxu.wu@huawei.com>, Feng Tang <feng.tang@intel.com>,
	Rob Herring <robh+dt@kernel.org>, <linux-spi@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v4 08/21] spi: dw: Refactor data IO procedure
Date: Thu, 8 Oct 2020 02:54:57 +0300	[thread overview]
Message-ID: <20201007235511.4935-9-Sergey.Semin@baikalelectronics.ru> (raw)
In-Reply-To: <20201007235511.4935-1-Sergey.Semin@baikalelectronics.ru>

The Tx and Rx data write/read procedure can be significantly simplified by
using Tx/Rx transfer lengths instead of the end pointers. By having the
Tx/Rx data leftover lengths (in the number of transfer words) we can get
rid of all subtraction and division operations utilized here and there in
the tx_max(), rx_max(), dw_writer() and dw_reader() methods. Such
modification will not only give us the more optimized IO procedures, but
will make the data IO methods much more readable than before.

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
---
 drivers/spi/spi-dw-core.c | 37 +++++++++++++++++--------------------
 drivers/spi/spi-dw.h      |  5 ++---
 2 files changed, 19 insertions(+), 23 deletions(-)

diff --git a/drivers/spi/spi-dw-core.c b/drivers/spi/spi-dw-core.c
index 01ab743bf177..3bb8aa3cba2b 100644
--- a/drivers/spi/spi-dw-core.c
+++ b/drivers/spi/spi-dw-core.c
@@ -108,9 +108,8 @@ EXPORT_SYMBOL_GPL(dw_spi_set_cs);
 /* Return the max entries we can fill into tx fifo */
 static inline u32 tx_max(struct dw_spi *dws)
 {
-	u32 tx_left, tx_room, rxtx_gap;
+	u32 tx_room, rxtx_gap;
 
-	tx_left = (dws->tx_end - dws->tx) / dws->n_bytes;
 	tx_room = dws->fifo_len - dw_readl(dws, DW_SPI_TXFLR);
 
 	/*
@@ -121,18 +120,15 @@ static inline u32 tx_max(struct dw_spi *dws)
 	 * shift registers. So a control from sw point of
 	 * view is taken.
 	 */
-	rxtx_gap =  ((dws->rx_end - dws->rx) - (dws->tx_end - dws->tx))
-			/ dws->n_bytes;
+	rxtx_gap = dws->fifo_len - (dws->rx_len - dws->tx_len);
 
-	return min3(tx_left, tx_room, (u32) (dws->fifo_len - rxtx_gap));
+	return min3((u32)dws->tx_len, tx_room, rxtx_gap);
 }
 
 /* Return the max entries we should read out of rx fifo */
 static inline u32 rx_max(struct dw_spi *dws)
 {
-	u32 rx_left = (dws->rx_end - dws->rx) / dws->n_bytes;
-
-	return min_t(u32, rx_left, dw_readl(dws, DW_SPI_RXFLR));
+	return min_t(u32, dws->rx_len, dw_readl(dws, DW_SPI_RXFLR));
 }
 
 static void dw_writer(struct dw_spi *dws)
@@ -141,15 +137,16 @@ static void dw_writer(struct dw_spi *dws)
 	u16 txw = 0;
 
 	while (max--) {
-		/* Set the tx word if the transfer's original "tx" is not null */
-		if (dws->tx_end - dws->len) {
+		if (dws->tx) {
 			if (dws->n_bytes == 1)
 				txw = *(u8 *)(dws->tx);
 			else
 				txw = *(u16 *)(dws->tx);
+
+			dws->tx += dws->n_bytes;
 		}
 		dw_write_io_reg(dws, DW_SPI_DR, txw);
-		dws->tx += dws->n_bytes;
+		--dws->tx_len;
 	}
 }
 
@@ -160,14 +157,15 @@ static void dw_reader(struct dw_spi *dws)
 
 	while (max--) {
 		rxw = dw_read_io_reg(dws, DW_SPI_DR);
-		/* Care rx only if the transfer's original "rx" is not null */
-		if (dws->rx_end - dws->len) {
+		if (dws->rx) {
 			if (dws->n_bytes == 1)
 				*(u8 *)(dws->rx) = rxw;
 			else
 				*(u16 *)(dws->rx) = rxw;
+
+			dws->rx += dws->n_bytes;
 		}
-		dws->rx += dws->n_bytes;
+		--dws->rx_len;
 	}
 }
 
@@ -192,7 +190,7 @@ static irqreturn_t interrupt_transfer(struct dw_spi *dws)
 	}
 
 	dw_reader(dws);
-	if (dws->rx_end == dws->rx) {
+	if (!dws->rx_len) {
 		spi_mask_intr(dws, 0xff);
 		spi_finalize_current_transfer(dws->master);
 		return IRQ_HANDLED;
@@ -320,12 +318,11 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 	dws->dma_mapped = 0;
 	dws->n_bytes = DIV_ROUND_UP(transfer->bits_per_word, BITS_PER_BYTE);
 	dws->tx = (void *)transfer->tx_buf;
-	dws->tx_end = dws->tx + transfer->len;
+	dws->tx_len = transfer->len / dws->n_bytes;
 	dws->rx = transfer->rx_buf;
-	dws->rx_end = dws->rx + transfer->len;
-	dws->len = transfer->len;
+	dws->rx_len = dws->tx_len;
 
-	/* Ensure dw->rx and dw->rx_end are visible */
+	/* Ensure the data above is visible for all CPUs */
 	smp_mb();
 
 	spi_enable_chip(dws, 0);
@@ -352,7 +349,7 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 			return ret;
 		}
 	} else {
-		txlevel = min_t(u16, dws->fifo_len / 2, dws->len / dws->n_bytes);
+		txlevel = min_t(u16, dws->fifo_len / 2, dws->tx_len);
 		dw_writel(dws, DW_SPI_TXFTLR, txlevel);
 
 		/* Set the interrupt mask */
diff --git a/drivers/spi/spi-dw.h b/drivers/spi/spi-dw.h
index 2a2346438564..cfc9f63acde4 100644
--- a/drivers/spi/spi-dw.h
+++ b/drivers/spi/spi-dw.h
@@ -147,11 +147,10 @@ struct dw_spi {
 	void (*set_cs)(struct spi_device *spi, bool enable);
 
 	/* Current message transfer state info */
-	size_t			len;
 	void			*tx;
-	void			*tx_end;
+	unsigned int		tx_len;
 	void			*rx;
-	void			*rx_end;
+	unsigned int		rx_len;
 	int			dma_mapped;
 	u8			n_bytes;	/* current is a 1/2 bytes op */
 	irqreturn_t		(*transfer_handler)(struct dw_spi *dws);
-- 
2.27.0


  parent reply	other threads:[~2020-10-07 23:56 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-10-07 23:54 [PATCH v4 00/21] spi: dw: Add full Baikal-T1 SPI Controllers support Serge Semin
2020-10-07 23:54 ` [PATCH v4 01/21] spi: dw: Use an explicit set_cs assignment Serge Semin
2020-10-07 23:54 ` [PATCH v4 02/21] spi: dw: Add DWC SSI capability Serge Semin
2020-10-07 23:54 ` [PATCH v4 03/21] spi: dw: Detach SPI device specific CR0 config method Serge Semin
2020-10-07 23:54 ` [PATCH v4 04/21] spi: dw: Update SPI bus speed in a config function Serge Semin
2020-10-07 23:54 ` [PATCH v4 05/21] spi: dw: Simplify the SPI bus speed config procedure Serge Semin
2020-10-07 23:54 ` [PATCH v4 06/21] spi: dw: Update Rx sample delay in the config function Serge Semin
2020-10-07 23:54 ` [PATCH v4 07/21] spi: dw: Add DW SPI controller config structure Serge Semin
2020-10-07 23:54 ` Serge Semin [this message]
2020-10-07 23:54 ` [PATCH v4 09/21] spi: dw: Refactor IRQ-based SPI transfer procedure Serge Semin
2020-10-07 23:54 ` [PATCH v4 10/21] spi: dw: Perform IRQ setup in a dedicated function Serge Semin
2020-10-07 23:55 ` [PATCH v4 11/21] spi: dw: Unmask IRQs after enabling the chip Serge Semin
2020-10-07 23:55 ` [PATCH v4 12/21] spi: dw: Discard chip enabling on DMA setup error Serge Semin
2020-10-07 23:55 ` [PATCH v4 13/21] spi: dw: De-assert chip-select on reset Serge Semin
2020-10-07 23:55 ` [PATCH v4 14/21] spi: dw: Explicitly de-assert CS on SPI transfer completion Serge Semin
2020-10-07 23:55 ` [PATCH v4 15/21] spi: dw: Move num-of retries parameter to the header file Serge Semin
2020-10-07 23:55 ` [PATCH v4 16/21] spi: dw: Add generic DW SSI status-check method Serge Semin
2020-10-07 23:55 ` [PATCH v4 17/21] spi: dw: Add memory operations support Serge Semin
2020-10-07 23:55 ` [PATCH v4 18/21] spi: dw: Introduce max mem-ops SPI bus frequency setting Serge Semin
2020-10-07 23:55 ` [PATCH v4 19/21] spi: dw: Add poll-based SPI transfers support Serge Semin
2020-10-07 23:55 ` [PATCH v4 20/21] dt-bindings: spi: dw: Add Baikal-T1 SPI Controllers Serge Semin
2020-10-07 23:55 ` [PATCH v4 21/21] spi: dw: Add Baikal-T1 SPI Controller glue driver Serge Semin
2020-10-08 22:02 ` [PATCH v4 00/21] spi: dw: Add full Baikal-T1 SPI Controllers support Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201007235511.4935-9-Sergey.Semin@baikalelectronics.ru \
    --to=sergey.semin@baikalelectronics.ru \
    --cc=Alexey.Malahov@baikalelectronics.ru \
    --cc=Pavel.Parkhomenko@baikalelectronics.ru \
    --cc=Ramil.Zaripov@baikalelectronics.ru \
    --cc=andriy.shevchenko@linux.intel.com \
    --cc=andy.shevchenko@gmail.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=fancer.lancer@gmail.com \
    --cc=feng.tang@intel.com \
    --cc=lars.povlsen@microchip.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=wuxu.wu@huawei.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.