From: Krzysztof Kozlowski <krzk@kernel.org> To: Sakari Ailus <sakari.ailus@linux.intel.com>, Mauro Carvalho Chehab <mchehab@kernel.org>, Rob Herring <robh+dt@kernel.org>, linux-media@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Cc: Krzysztof Kozlowski <krzk@kernel.org>, Rob Herring <robh@kernel.org> Subject: [PATCH v6 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor Date: Wed, 18 Nov 2020 21:27:12 +0100 [thread overview] Message-ID: <20201118202715.6692-1-krzk@kernel.org> (raw) Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes since v4: 1. Add clock-lanes, 2. Add Rob's review, 3. Add one more example and extend existing one, 4. Add common clock properties (assigned-*). Changes since v3: 1. Document also two lane setup. Changes since v2: 1. Remove clock-frequency, add reset GPIOs, add supplies. 2. Use additionalProperties. Changes since v1: 1. None --- .../devicetree/bindings/media/i2c/imx258.yaml | 140 ++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 141 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/imx258.yaml diff --git a/Documentation/devicetree/bindings/media/i2c/imx258.yaml b/Documentation/devicetree/bindings/media/i2c/imx258.yaml new file mode 100644 index 000000000000..4a3471fb88a1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx258.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imx258.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: |- + IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel + type stacked image sensor with a square pixel array of size 4208 x 3120. It + is programmable through I2C interface. Image data is sent through MIPI + CSI-2. + +properties: + compatible: + const: sony,imx258 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + description: + Clock frequency from 6 to 27 MHz. + maxItems: 1 + + reg: + maxItems: 1 + + reset-gpios: + description: |- + Reference to the GPIO connected to the XCLR pin, if any. + + vana-supply: + description: + Analog voltage (VANA) supply, 2.7 V + + vdig-supply: + description: + Digital I/O voltage (VDIG) supply, 1.2 V + + vif-supply: + description: + Interface voltage (VIF) supply, 1.8 V + + # See ../video-interfaces.txt for more details + port: + type: object + properties: + endpoint: + type: object + properties: + clock-lanes: + const: 0 + + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-array + description: + Allowed data bus frequencies. + + required: + - clock-lanes + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <320000000>; + }; + }; + }; + }; + + /* Oscillator on the camera board */ + imx258_clk: clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; + + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + assigned-clocks = <&imx258_clk>; + assigned-clock-rates = <19200000>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <633600000>; + }; + }; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 82ea6867ac2e..96ca9d2857db 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -16395,6 +16395,7 @@ M: Sakari Ailus <sakari.ailus@linux.intel.com> L: linux-media@vger.kernel.org S: Maintained T: git git://linuxtv.org/media_tree.git +F: Documentation/devicetree/bindings/media/i2c/imx258.yaml F: drivers/media/i2c/imx258.c SONY IMX274 SENSOR DRIVER -- 2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Krzysztof Kozlowski <krzk@kernel.org> To: Sakari Ailus <sakari.ailus@linux.intel.com>, Mauro Carvalho Chehab <mchehab@kernel.org>, Rob Herring <robh+dt@kernel.org>, linux-media@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Cc: Rob Herring <robh@kernel.org>, Krzysztof Kozlowski <krzk@kernel.org> Subject: [PATCH v6 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor Date: Wed, 18 Nov 2020 21:27:12 +0100 [thread overview] Message-ID: <20201118202715.6692-1-krzk@kernel.org> (raw) Add bindings for the IMX258 camera sensor. The bindings, just like the driver, are quite limited, e.g. do not support regulator supplies. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes since v4: 1. Add clock-lanes, 2. Add Rob's review, 3. Add one more example and extend existing one, 4. Add common clock properties (assigned-*). Changes since v3: 1. Document also two lane setup. Changes since v2: 1. Remove clock-frequency, add reset GPIOs, add supplies. 2. Use additionalProperties. Changes since v1: 1. None --- .../devicetree/bindings/media/i2c/imx258.yaml | 140 ++++++++++++++++++ MAINTAINERS | 1 + 2 files changed, 141 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/imx258.yaml diff --git a/Documentation/devicetree/bindings/media/i2c/imx258.yaml b/Documentation/devicetree/bindings/media/i2c/imx258.yaml new file mode 100644 index 000000000000..4a3471fb88a1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx258.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/imx258.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: |- + IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel + type stacked image sensor with a square pixel array of size 4208 x 3120. It + is programmable through I2C interface. Image data is sent through MIPI + CSI-2. + +properties: + compatible: + const: sony,imx258 + + assigned-clocks: true + assigned-clock-parents: true + assigned-clock-rates: true + + clocks: + description: + Clock frequency from 6 to 27 MHz. + maxItems: 1 + + reg: + maxItems: 1 + + reset-gpios: + description: |- + Reference to the GPIO connected to the XCLR pin, if any. + + vana-supply: + description: + Analog voltage (VANA) supply, 2.7 V + + vdig-supply: + description: + Digital I/O voltage (VDIG) supply, 1.2 V + + vif-supply: + description: + Interface voltage (VIF) supply, 1.8 V + + # See ../video-interfaces.txt for more details + port: + type: object + properties: + endpoint: + type: object + properties: + clock-lanes: + const: 0 + + data-lanes: + oneOf: + - items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 + - items: + - const: 1 + - const: 2 + + link-frequencies: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-array + description: + Allowed data bus frequencies. + + required: + - clock-lanes + - data-lanes + - link-frequencies + +required: + - compatible + - reg + - port + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <320000000>; + }; + }; + }; + }; + + /* Oscillator on the camera board */ + imx258_clk: clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; + + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6c { + compatible = "sony,imx258"; + reg = <0x6c>; + clocks = <&imx258_clk>; + + assigned-clocks = <&imx258_clk>; + assigned-clock-rates = <19200000>; + + port { + endpoint { + remote-endpoint = <&csi1_ep>; + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <633600000>; + }; + }; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 82ea6867ac2e..96ca9d2857db 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -16395,6 +16395,7 @@ M: Sakari Ailus <sakari.ailus@linux.intel.com> L: linux-media@vger.kernel.org S: Maintained T: git git://linuxtv.org/media_tree.git +F: Documentation/devicetree/bindings/media/i2c/imx258.yaml F: drivers/media/i2c/imx258.c SONY IMX274 SENSOR DRIVER -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2020-11-18 20:27 UTC|newest] Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-11-18 20:27 Krzysztof Kozlowski [this message] 2020-11-18 20:27 ` [PATCH v6 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor Krzysztof Kozlowski 2020-11-18 20:27 ` [PATCH v6 2/4] media: i2c: imx258: add support for binding via device tree Krzysztof Kozlowski 2020-11-18 20:27 ` Krzysztof Kozlowski 2020-11-18 20:27 ` [PATCH v6 3/4] media: i2c: imx258: simplify getting state container Krzysztof Kozlowski 2020-11-18 20:27 ` Krzysztof Kozlowski 2020-11-18 20:27 ` [PATCH v6 4/4] media: i2c: imx258: get clock from device properties and enable it via runtime PM Krzysztof Kozlowski 2020-11-18 20:27 ` Krzysztof Kozlowski 2021-01-22 9:18 ` [PATCH v6 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor Sakari Ailus 2021-01-22 9:18 ` Sakari Ailus 2021-01-27 12:23 ` Krzysztof Kozlowski 2021-01-27 12:23 ` Krzysztof Kozlowski 2021-01-27 12:26 ` Krzysztof Kozlowski 2021-01-27 12:26 ` Krzysztof Kozlowski 2021-01-27 12:45 ` Sakari Ailus 2021-01-27 12:45 ` Sakari Ailus 2021-01-27 12:51 ` Krzysztof Kozlowski 2021-01-27 12:51 ` Krzysztof Kozlowski
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20201118202715.6692-1-krzk@kernel.org \ --to=krzk@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-media@vger.kernel.org \ --cc=mchehab@kernel.org \ --cc=robh+dt@kernel.org \ --cc=robh@kernel.org \ --cc=sakari.ailus@linux.intel.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.