From: Alexandre Belloni <alexandre.belloni@bootlin.com> To: Jonathan Cameron <jic23@kernel.org> Cc: Lars-Peter Clausen <lars@metafoo.de>, Peter Meerwald-Stadler <pmeerw@pmeerw.net>, Nicolas Ferre <nicolas.ferre@microchip.com>, Ludovic Desroches <ludovic.desroches@microchip.com>, linux-iio@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, Alexandre Belloni <alexandre.belloni@bootlin.com>, Rob Herring <robh+dt@kernel.org> Subject: [PATCH v3 03/10] dt-bindings:iio:adc:remove atmel,adc-res and atmel,adc-res-names Date: Sat, 28 Nov 2020 23:28:11 +0100 [thread overview] Message-ID: <20201128222818.1910764-4-alexandre.belloni@bootlin.com> (raw) In-Reply-To: <20201128222818.1910764-1-alexandre.belloni@bootlin.com> Remove atmel,adc-res and atmel,adc-res-names as they are not necessary and are handled by the driver. Also add sama5d3 to the list of possible chips. Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> --- .../devicetree/bindings/iio/adc/at91_adc.txt | 13 ++++--------- 1 file changed, 4 insertions(+), 9 deletions(-) diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt index f65b04fb7962..da393ac5c05f 100644 --- a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Should be "atmel,<chip>-adc" - <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5" + <chip> can be "at91sam9260", "at91sam9g45", "at91sam9x5" or "sama5d3" - reg: Should contain ADC registers location and length - interrupts: Should contain the IRQ line for the ADC - clock-names: tuple listing input clock names. @@ -13,17 +13,12 @@ Required properties: - atmel,adc-startup-time: Startup Time of the ADC in microseconds as defined in the datasheet - atmel,adc-vref: Reference voltage in millivolts for the conversions - - atmel,adc-res: List of resolutions in bits supported by the ADC. List size - must be two at least. - - atmel,adc-res-names: Contains one identifier string for each resolution - in atmel,adc-res property. "lowres" and "highres" - identifiers are required. Optional properties: - atmel,adc-use-external-triggers: Boolean to enable the external triggers - - atmel,adc-use-res: String corresponding to an identifier from - atmel,adc-res-names property. If not specified, the highest - resolution will be used. + - atmel,adc-use-res: String selecting the resolution, can be "lowres" or + "highres". If not specified, the highest resolution will + be used. - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this -- 2.28.0
WARNING: multiple messages have this Message-ID (diff)
From: Alexandre Belloni <alexandre.belloni@bootlin.com> To: Jonathan Cameron <jic23@kernel.org> Cc: devicetree@vger.kernel.org, Alexandre Belloni <alexandre.belloni@bootlin.com>, Lars-Peter Clausen <lars@metafoo.de>, linux-iio@vger.kernel.org, linux-kernel@vger.kernel.org, Ludovic Desroches <ludovic.desroches@microchip.com>, Rob Herring <robh+dt@kernel.org>, Peter Meerwald-Stadler <pmeerw@pmeerw.net>, linux-arm-kernel@lists.infradead.org Subject: [PATCH v3 03/10] dt-bindings:iio:adc:remove atmel, adc-res and atmel, adc-res-names Date: Sat, 28 Nov 2020 23:28:11 +0100 [thread overview] Message-ID: <20201128222818.1910764-4-alexandre.belloni@bootlin.com> (raw) In-Reply-To: <20201128222818.1910764-1-alexandre.belloni@bootlin.com> Remove atmel,adc-res and atmel,adc-res-names as they are not necessary and are handled by the driver. Also add sama5d3 to the list of possible chips. Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> --- .../devicetree/bindings/iio/adc/at91_adc.txt | 13 ++++--------- 1 file changed, 4 insertions(+), 9 deletions(-) diff --git a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt index f65b04fb7962..da393ac5c05f 100644 --- a/Documentation/devicetree/bindings/iio/adc/at91_adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Should be "atmel,<chip>-adc" - <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5" + <chip> can be "at91sam9260", "at91sam9g45", "at91sam9x5" or "sama5d3" - reg: Should contain ADC registers location and length - interrupts: Should contain the IRQ line for the ADC - clock-names: tuple listing input clock names. @@ -13,17 +13,12 @@ Required properties: - atmel,adc-startup-time: Startup Time of the ADC in microseconds as defined in the datasheet - atmel,adc-vref: Reference voltage in millivolts for the conversions - - atmel,adc-res: List of resolutions in bits supported by the ADC. List size - must be two at least. - - atmel,adc-res-names: Contains one identifier string for each resolution - in atmel,adc-res property. "lowres" and "highres" - identifiers are required. Optional properties: - atmel,adc-use-external-triggers: Boolean to enable the external triggers - - atmel,adc-use-res: String corresponding to an identifier from - atmel,adc-res-names property. If not specified, the highest - resolution will be used. + - atmel,adc-use-res: String selecting the resolution, can be "lowres" or + "highres". If not specified, the highest resolution will + be used. - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this -- 2.28.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-11-28 22:29 UTC|newest] Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-11-28 22:28 [PATCH v3 00/10] iio: adc: at91_adc: cleanup DT bindings Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 01/10] iio: adc: at91_adc: remove at91_adc_ids Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 02/10] iio: adc: at91_adc: rework resolution selection Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni [this message] 2020-11-28 22:28 ` [PATCH v3 03/10] dt-bindings:iio:adc:remove atmel, adc-res and atmel, adc-res-names Alexandre Belloni 2020-12-08 21:35 ` Rob Herring 2020-12-08 21:35 ` Rob Herring 2020-11-28 22:28 ` [PATCH v3 04/10] dt-bindings:iio:adc:atmel,sama9260-adc: conversion to yaml from at91_adc.txt Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 04/10] dt-bindings:iio:adc:atmel, sama9260-adc: " Alexandre Belloni 2020-11-29 12:01 ` [PATCH v3 04/10] dt-bindings:iio:adc:atmel,sama9260-adc: " Jonathan Cameron 2020-11-29 12:01 ` Jonathan Cameron 2020-11-28 22:28 ` [PATCH v3 05/10] iio: adc: at91_adc: rework trigger definition Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 06/10] dt-bindings:iio:adc:remove triggers Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 07/10] iio: adc: at91_adc: merge at91_adc_probe_dt back in at91_adc_probe Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 08/10] ARM: dts: at91: sama5d3: use proper ADC compatible Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 09/10] ARM: dts: at91: at91sam9rl: fix ADC triggers Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-28 22:28 ` [PATCH v3 10/10] ARM: dts: at91: remove deprecated ADC properties Alexandre Belloni 2020-11-28 22:28 ` Alexandre Belloni 2020-11-29 13:01 ` [PATCH v3 00/10] iio: adc: at91_adc: cleanup DT bindings Jonathan Cameron 2020-11-29 13:01 ` Jonathan Cameron
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20201128222818.1910764-4-alexandre.belloni@bootlin.com \ --to=alexandre.belloni@bootlin.com \ --cc=devicetree@vger.kernel.org \ --cc=jic23@kernel.org \ --cc=lars@metafoo.de \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-iio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=ludovic.desroches@microchip.com \ --cc=nicolas.ferre@microchip.com \ --cc=pmeerw@pmeerw.net \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.