From: Sebastian Reichel <sebastian.reichel@collabora.com> To: Sebastian Reichel <sebastian.reichel@collabora.com>, Shawn Guo <shawnguo@kernel.org>, Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix Kernel Team <kernel@pengutronix.de>, Fabio Estevam <festevam@gmail.com>, NXP Linux Team <linux-imx@nxp.com> Cc: Rob Herring <robh+dt@kernel.org>, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, kernel@collabora.com Subject: [PATCHv1 2/4] ARM: dts: imx: ba16: improve PHY information Date: Tue, 23 Feb 2021 19:33:44 +0100 [thread overview] Message-ID: <20210223183346.138575-3-sebastian.reichel@collabora.com> (raw) In-Reply-To: <20210223183346.138575-1-sebastian.reichel@collabora.com> Add PHY voltage supply information fixing the following kernel message: 2188000.ethernet supply phy not found, using dummy regulator Also add PHY clock information to avoid depending on the bootloader programming correct values. The bootloader also sets some reserved registers in the PHY as advised by Qualcomm, which is not supported by the bindings/kernel driver, so the reset GPIO has not been added intentionally. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> --- arch/arm/boot/dts/imx6q-ba16.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/imx6q-ba16.dtsi b/arch/arm/boot/dts/imx6q-ba16.dtsi index 4793ef5171aa..a684d999e605 100644 --- a/arch/arm/boot/dts/imx6q-ba16.dtsi +++ b/arch/arm/boot/dts/imx6q-ba16.dtsi @@ -177,6 +177,18 @@ &fec { pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii-id"; status = "okay"; + phy-supply = <®_3p3v>; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@4 { + reg = <4>; + qca,clk-out-frequency = <125000000>; + }; + }; }; &hdmi { -- 2.30.0
WARNING: multiple messages have this Message-ID (diff)
From: Sebastian Reichel <sebastian.reichel@collabora.com> To: Sebastian Reichel <sebastian.reichel@collabora.com>, Shawn Guo <shawnguo@kernel.org>, Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix Kernel Team <kernel@pengutronix.de>, Fabio Estevam <festevam@gmail.com>, NXP Linux Team <linux-imx@nxp.com> Cc: devicetree@vger.kernel.org, Rob Herring <robh+dt@kernel.org>, kernel@collabora.com, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org Subject: [PATCHv1 2/4] ARM: dts: imx: ba16: improve PHY information Date: Tue, 23 Feb 2021 19:33:44 +0100 [thread overview] Message-ID: <20210223183346.138575-3-sebastian.reichel@collabora.com> (raw) In-Reply-To: <20210223183346.138575-1-sebastian.reichel@collabora.com> Add PHY voltage supply information fixing the following kernel message: 2188000.ethernet supply phy not found, using dummy regulator Also add PHY clock information to avoid depending on the bootloader programming correct values. The bootloader also sets some reserved registers in the PHY as advised by Qualcomm, which is not supported by the bindings/kernel driver, so the reset GPIO has not been added intentionally. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> --- arch/arm/boot/dts/imx6q-ba16.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/imx6q-ba16.dtsi b/arch/arm/boot/dts/imx6q-ba16.dtsi index 4793ef5171aa..a684d999e605 100644 --- a/arch/arm/boot/dts/imx6q-ba16.dtsi +++ b/arch/arm/boot/dts/imx6q-ba16.dtsi @@ -177,6 +177,18 @@ &fec { pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii-id"; status = "okay"; + phy-supply = <®_3p3v>; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@4 { + reg = <4>; + qca,clk-out-frequency = <125000000>; + }; + }; }; &hdmi { -- 2.30.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-02-23 18:34 UTC|newest] Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-02-23 18:33 [PATCHv1 0/4] Bx50v3 DT improvements Sebastian Reichel 2021-02-23 18:33 ` Sebastian Reichel 2021-02-23 18:33 ` [PATCHv1 1/4] ARM: dts: imx: ba16: add USB OTG VBUS enable GPIO Sebastian Reichel 2021-02-23 18:33 ` Sebastian Reichel 2021-03-08 0:35 ` Shawn Guo 2021-03-08 0:35 ` Shawn Guo 2021-02-23 18:33 ` Sebastian Reichel [this message] 2021-02-23 18:33 ` [PATCHv1 2/4] ARM: dts: imx: ba16: improve PHY information Sebastian Reichel 2021-03-08 0:38 ` Shawn Guo 2021-03-08 0:38 ` Shawn Guo 2021-02-23 18:33 ` [PATCHv1 3/4] ARM: dts: imx: bx50v3: i2c GPIOs are open drain Sebastian Reichel 2021-02-23 18:33 ` Sebastian Reichel 2021-02-23 18:33 ` [PATCHv1 4/4] ARM: dts: imx: bx50v3: Define GPIO line names Sebastian Reichel 2021-02-23 18:33 ` Sebastian Reichel
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210223183346.138575-3-sebastian.reichel@collabora.com \ --to=sebastian.reichel@collabora.com \ --cc=devicetree@vger.kernel.org \ --cc=festevam@gmail.com \ --cc=kernel@collabora.com \ --cc=kernel@pengutronix.de \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-imx@nxp.com \ --cc=linux-kernel@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=s.hauer@pengutronix.de \ --cc=shawnguo@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.