From: Hsin-Yi Wang <hsinyi@chromium.org> To: Xin Ji <xji@analogixsemi.com>, dri-devel@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie>, Robert Foss <robert.foss@linaro.org>, Sam Ravnborg <sam@ravnborg.org>, Rob Herring <robh+dt@kernel.org>, Daniel Vetter <daniel@ffwll.ch>, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Laurent Pinchart <Laurent.pinchart@ideasonboard.com>, Neil Armstrong <narmstrong@baylibre.com> Subject: [PATCH v4 2/2] drm/bridge: anx7625: disable regulators when power off Date: Wed, 24 Feb 2021 14:14:09 +0800 [thread overview] Message-ID: <20210224061409.3996755-2-hsinyi@chromium.org> (raw) In-Reply-To: <20210224061409.3996755-1-hsinyi@chromium.org> When suspending the driver, anx7625_power_standby() will be called to turn off reset-gpios and enable-gpios. However, power supplies are not disabled. To save power, the driver can get the power supply regulators and turn off them in anx7625_power_standby(). Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> --- drivers/gpu/drm/bridge/analogix/anx7625.c | 34 +++++++++++++++++++++++ drivers/gpu/drm/bridge/analogix/anx7625.h | 1 + 2 files changed, 35 insertions(+) diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c index 65cc05982f826..23283ba0c4f93 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.c +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c @@ -11,6 +11,7 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/mutex.h> +#include <linux/regulator/consumer.h> #include <linux/slab.h> #include <linux/types.h> #include <linux/workqueue.h> @@ -875,12 +876,25 @@ static int sp_tx_edid_read(struct anx7625_data *ctx, static void anx7625_power_on(struct anx7625_data *ctx) { struct device *dev = &ctx->client->dev; + int ret, i; if (!ctx->pdata.low_power_mode) { DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); return; } + for (i = 0; i < ARRAY_SIZE(ctx->pdata.supplies); i++) { + ret = regulator_enable(ctx->pdata.supplies[i].consumer); + if (ret < 0) { + DRM_DEV_DEBUG_DRIVER(dev, "cannot enable supply %d: %d\n", + i, ret); + goto reg_err; + } + usleep_range(2000, 2100); + } + + usleep_range(4000, 4100); + /* Power on pin enable */ gpiod_set_value(ctx->pdata.gpio_p_on, 1); usleep_range(10000, 11000); @@ -889,11 +903,16 @@ static void anx7625_power_on(struct anx7625_data *ctx) usleep_range(10000, 11000); DRM_DEV_DEBUG_DRIVER(dev, "power on !\n"); + return; +reg_err: + for (--i; i >= 0; i--) + regulator_disable(ctx->pdata.supplies[i].consumer); } static void anx7625_power_standby(struct anx7625_data *ctx) { struct device *dev = &ctx->client->dev; + int ret; if (!ctx->pdata.low_power_mode) { DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); @@ -904,6 +923,12 @@ static void anx7625_power_standby(struct anx7625_data *ctx) usleep_range(1000, 1100); gpiod_set_value(ctx->pdata.gpio_p_on, 0); usleep_range(1000, 1100); + + ret = regulator_bulk_disable(ARRAY_SIZE(ctx->pdata.supplies), + ctx->pdata.supplies); + if (ret < 0) + DRM_DEV_DEBUG_DRIVER(dev, "cannot disable supplies %d\n", ret); + DRM_DEV_DEBUG_DRIVER(dev, "power down\n"); } @@ -1742,6 +1767,15 @@ static int anx7625_i2c_probe(struct i2c_client *client, platform->client = client; i2c_set_clientdata(client, platform); + pdata->supplies[0].supply = "vdd10"; + pdata->supplies[1].supply = "vdd18"; + pdata->supplies[2].supply = "vdd33"; + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(pdata->supplies), + pdata->supplies); + if (ret) { + DRM_DEV_ERROR(dev, "fail to get power supplies: %d\n", ret); + return ret; + } anx7625_init_gpio(platform); atomic_set(&platform->power_status, 0); diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h index 193ad86c54503..e4a086b3a3d7b 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.h +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h @@ -350,6 +350,7 @@ struct s_edid_data { struct anx7625_platform_data { struct gpio_desc *gpio_p_on; struct gpio_desc *gpio_reset; + struct regulator_bulk_data supplies[3]; struct drm_bridge *panel_bridge; int intp_irq; u32 low_power_mode; -- 2.30.1.766.gb4fecdf3b7-goog
WARNING: multiple messages have this Message-ID (diff)
From: Hsin-Yi Wang <hsinyi@chromium.org> To: Xin Ji <xji@analogixsemi.com>, dri-devel@lists.freedesktop.org Cc: devicetree@vger.kernel.org, Neil Armstrong <narmstrong@baylibre.com>, David Airlie <airlied@linux.ie>, linux-kernel@vger.kernel.org, Robert Foss <robert.foss@linaro.org>, Rob Herring <robh+dt@kernel.org>, Laurent Pinchart <Laurent.pinchart@ideasonboard.com>, Sam Ravnborg <sam@ravnborg.org> Subject: [PATCH v4 2/2] drm/bridge: anx7625: disable regulators when power off Date: Wed, 24 Feb 2021 14:14:09 +0800 [thread overview] Message-ID: <20210224061409.3996755-2-hsinyi@chromium.org> (raw) In-Reply-To: <20210224061409.3996755-1-hsinyi@chromium.org> When suspending the driver, anx7625_power_standby() will be called to turn off reset-gpios and enable-gpios. However, power supplies are not disabled. To save power, the driver can get the power supply regulators and turn off them in anx7625_power_standby(). Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> --- drivers/gpu/drm/bridge/analogix/anx7625.c | 34 +++++++++++++++++++++++ drivers/gpu/drm/bridge/analogix/anx7625.h | 1 + 2 files changed, 35 insertions(+) diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c index 65cc05982f826..23283ba0c4f93 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.c +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c @@ -11,6 +11,7 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/mutex.h> +#include <linux/regulator/consumer.h> #include <linux/slab.h> #include <linux/types.h> #include <linux/workqueue.h> @@ -875,12 +876,25 @@ static int sp_tx_edid_read(struct anx7625_data *ctx, static void anx7625_power_on(struct anx7625_data *ctx) { struct device *dev = &ctx->client->dev; + int ret, i; if (!ctx->pdata.low_power_mode) { DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); return; } + for (i = 0; i < ARRAY_SIZE(ctx->pdata.supplies); i++) { + ret = regulator_enable(ctx->pdata.supplies[i].consumer); + if (ret < 0) { + DRM_DEV_DEBUG_DRIVER(dev, "cannot enable supply %d: %d\n", + i, ret); + goto reg_err; + } + usleep_range(2000, 2100); + } + + usleep_range(4000, 4100); + /* Power on pin enable */ gpiod_set_value(ctx->pdata.gpio_p_on, 1); usleep_range(10000, 11000); @@ -889,11 +903,16 @@ static void anx7625_power_on(struct anx7625_data *ctx) usleep_range(10000, 11000); DRM_DEV_DEBUG_DRIVER(dev, "power on !\n"); + return; +reg_err: + for (--i; i >= 0; i--) + regulator_disable(ctx->pdata.supplies[i].consumer); } static void anx7625_power_standby(struct anx7625_data *ctx) { struct device *dev = &ctx->client->dev; + int ret; if (!ctx->pdata.low_power_mode) { DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n"); @@ -904,6 +923,12 @@ static void anx7625_power_standby(struct anx7625_data *ctx) usleep_range(1000, 1100); gpiod_set_value(ctx->pdata.gpio_p_on, 0); usleep_range(1000, 1100); + + ret = regulator_bulk_disable(ARRAY_SIZE(ctx->pdata.supplies), + ctx->pdata.supplies); + if (ret < 0) + DRM_DEV_DEBUG_DRIVER(dev, "cannot disable supplies %d\n", ret); + DRM_DEV_DEBUG_DRIVER(dev, "power down\n"); } @@ -1742,6 +1767,15 @@ static int anx7625_i2c_probe(struct i2c_client *client, platform->client = client; i2c_set_clientdata(client, platform); + pdata->supplies[0].supply = "vdd10"; + pdata->supplies[1].supply = "vdd18"; + pdata->supplies[2].supply = "vdd33"; + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(pdata->supplies), + pdata->supplies); + if (ret) { + DRM_DEV_ERROR(dev, "fail to get power supplies: %d\n", ret); + return ret; + } anx7625_init_gpio(platform); atomic_set(&platform->power_status, 0); diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h index 193ad86c54503..e4a086b3a3d7b 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.h +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h @@ -350,6 +350,7 @@ struct s_edid_data { struct anx7625_platform_data { struct gpio_desc *gpio_p_on; struct gpio_desc *gpio_reset; + struct regulator_bulk_data supplies[3]; struct drm_bridge *panel_bridge; int intp_irq; u32 low_power_mode; -- 2.30.1.766.gb4fecdf3b7-goog _______________________________________________ dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
next prev parent reply other threads:[~2021-02-24 6:18 UTC|newest] Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-02-24 6:14 [PATCH v4 1/2] dt-bindings: drm/bridge: anx7625: Add power supplies Hsin-Yi Wang 2021-02-24 6:14 ` Hsin-Yi Wang 2021-02-24 6:14 ` Hsin-Yi Wang [this message] 2021-02-24 6:14 ` [PATCH v4 2/2] drm/bridge: anx7625: disable regulators when power off Hsin-Yi Wang 2021-03-18 4:26 ` Hsin-Yi Wang 2021-03-18 4:26 ` Hsin-Yi Wang 2021-03-19 2:49 ` Xin Ji 2021-03-19 2:49 ` Xin Ji
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210224061409.3996755-2-hsinyi@chromium.org \ --to=hsinyi@chromium.org \ --cc=Laurent.pinchart@ideasonboard.com \ --cc=airlied@linux.ie \ --cc=daniel@ffwll.ch \ --cc=devicetree@vger.kernel.org \ --cc=dri-devel@lists.freedesktop.org \ --cc=linux-kernel@vger.kernel.org \ --cc=narmstrong@baylibre.com \ --cc=robert.foss@linaro.org \ --cc=robh+dt@kernel.org \ --cc=sam@ravnborg.org \ --cc=xji@analogixsemi.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.