From: Roja Rani Yarubandi <rojay@codeaurora.org>
To: agross@kernel.org, bjorn.andersson@linaro.org, robh+dt@kernel.org
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Rajendra Nayak <rnayak@codeaurora.org>,
saiprakash.ranjan@codeaurora.org, msavaliy@qti.qualcomm.com,
Roja Rani Yarubandi <rojay@codeaurora.org>
Subject: [PATCH V2] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes
Date: Thu, 22 Apr 2021 20:35:56 +0530 [thread overview]
Message-ID: <20210422150556.450-1-rojay@codeaurora.org> (raw)
Add QSPI and QUP SE instances configuration for sc7280.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
---
Changes in V2:
- As per Doug's comments removed pinmux/pinconf subnodes.
- As per Doug's comments split of SPI, UART nodes has been done.
- Moved QSPI node before aps_smmu as per the order.
This patch depends on interconnect changes [1]
[1] https://lore.kernel.org/patchwork/project/lkml/list/?series=488429
arch/arm64/boot/dts/qcom/sc7280-idp.dts | 131 +-
arch/arm64/boot/dts/qcom/sc7280.dtsi | 2377 +++++++++++++++++++----
2 files changed, 2089 insertions(+), 419 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 54d2cb365b71..b1e948a72eb1 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -15,6 +15,7 @@ / {
aliases {
serial0 = &uart5;
+ hsuart0 = &uart7;
};
chosen {
@@ -234,26 +235,140 @@ vreg_l6e_0p8: ldo6 {
};
};
+&qspi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ /* TODO: Increase frequency after testing */
+ spi-max-frequency = <25000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+};
+
&qupv3_id_0 {
status = "okay";
};
+&qupv3_id_1 {
+ status = "okay";
+};
+
&uart5 {
status = "okay";
};
+&uart7 {
+ status = "okay";
+
+ /delete-property/interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
-&qup_uart5_default {
- tx {
- pins = "gpio46";
- drive-strength = <2>;
- bias-disable;
+&qspi_cs0 {
+ bias-disable;
+};
+
+&qspi_clk {
+ bias-disable;
+};
+
+&qspi_data01 {
+ /* High-Z when no transfers; nice to park the lines */
+ bias-pull-up;
+};
+
+&qup_uart5_tx {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart5_rx {
+ drive-strength = <2>;
+ bias-pull-up;
+};
+
+&qup_uart7_cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+};
+
+&qup_uart7_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&tlmm {
+ qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+ pins = "gpio28";
+ function = "gpio";
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+ pins = "gpio29";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+ pins = "gpio30";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
};
- rx {
- pins = "gpio47";
- drive-strength = <2>;
+ qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+ pins = "gpio31";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
bias-pull-up;
};
};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 2cc478553935..42bb2dda9047 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -293,6 +293,25 @@ ipcc: mailbox@408000 {
#mbox-cells = <2>;
};
+ qup_opp_table: qup-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-128000000 {
+ opp-hz = /bits/ 64 <128000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0 0x009c0000 0 0x2000>;
@@ -302,575 +321,2111 @@ qupv3_id_0: geniqup@9c0000 {
#address-cells = <2>;
#size-cells = <2>;
ranges;
+ iommus = <&apps_smmu 0x123 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>;
+ interconnect-names = "qup-core";
status = "disabled";
- uart5: serial@994000 {
- compatible = "qcom,geni-debug-uart";
- reg = <0 0x00994000 0 0x4000>;
+ i2c0: i2c@980000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00980000 0 0x4000>;
clock-names = "se";
- clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
pinctrl-names = "default";
- pinctrl-0 = <&qup_uart5_default>;
- interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-0 = <&qup_i2c0_data_clk>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
status = "disabled";
};
- };
- stm@6002000 {
- compatible = "arm,coresight-stm", "arm,primecell";
- reg = <0 0x06002000 0 0x1000>,
- <0 0x16280000 0 0x180000>;
- reg-names = "stm-base", "stm-stimulus-base";
-
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
-
- out-ports {
- port {
- stm_out: endpoint {
- remote-endpoint = <&funnel0_in7>;
- };
- };
+ spi0: spi@980000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
};
- };
-
- funnel@6041000 {
- compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
- reg = <0 0x06041000 0 0x1000>;
-
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- out-ports {
- port {
- funnel0_out: endpoint {
- remote-endpoint = <&merge_funnel_in0>;
- };
- };
+ uart0: serial@980000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00980000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
};
- in-ports {
+ i2c1: i2c@984000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_data_clk>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
-
- port@7 {
- reg = <7>;
- funnel0_in7: endpoint {
- remote-endpoint = <&stm_out>;
- };
- };
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
};
- };
-
- funnel@6042000 {
- compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
- reg = <0 0x06042000 0 0x1000>;
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
+ spi1: spi@984000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>, <&qup_spi1_cs_gpio>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- out-ports {
- port {
- funnel1_out: endpoint {
- remote-endpoint = <&merge_funnel_in1>;
- };
- };
+ uart1: serial@984000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00984000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
};
- in-ports {
+ i2c2: i2c@988000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_data_clk>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
-
- port@4 {
- reg = <4>;
- funnel1_in4: endpoint {
- remote-endpoint = <&apss_merge_funnel_out>;
- };
- };
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
};
- };
-
- funnel@6045000 {
- compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
- reg = <0 0x06045000 0 0x1000>;
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
+ spi2: spi@988000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>, <&qup_spi2_cs_gpio>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- out-ports {
- port {
- merge_funnel_out: endpoint {
- remote-endpoint = <&swao_funnel_in>;
- };
- };
+ uart2: serial@988000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00988000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
};
- in-ports {
+ i2c3: i2c@98c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_data_clk>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
- port@0 {
- reg = <0>;
- merge_funnel_in0: endpoint {
- remote-endpoint = <&funnel0_out>;
- };
- };
+ spi3: spi@98c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>, <&qup_spi3_cs_gpio>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- port@1 {
- reg = <1>;
- merge_funnel_in1: endpoint {
- remote-endpoint = <&funnel1_out>;
- };
- };
+ uart3: serial@98c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0098c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
};
- };
- replicator@6046000 {
- compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
- reg = <0 0x06046000 0 0x1000>;
+ i2c4: i2c@990000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_data_clk>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
+ spi4: spi@990000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>, <&qup_spi4_cs_gpio>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- out-ports {
- port {
- replicator_out: endpoint {
- remote-endpoint = <&etr_in>;
- };
- };
+ uart4: serial@990000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00990000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
};
- in-ports {
- port {
- replicator_in: endpoint {
- remote-endpoint = <&swao_replicator_out>;
- };
- };
+ i2c5: i2c@994000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00994000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_data_clk>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
};
- };
- etr@6048000 {
- compatible = "arm,coresight-tmc", "arm,primecell";
- reg = <0 0x06048000 0 0x1000>;
- iommus = <&apps_smmu 0x04c0 0>;
+ spi5: spi@994000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00994000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>, <&qup_spi5_cs_gpio>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- arm,scatter-gather;
+ uart5: serial@994000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0 0x00994000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- in-ports {
- port {
- etr_in: endpoint {
- remote-endpoint = <&replicator_out>;
- };
- };
+ i2c6: i2c@998000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_data_clk>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
};
- };
- funnel@6b04000 {
- compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
- reg = <0 0x06b04000 0 0x1000>;
+ spi6: spi@998000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>, <&qup_spi6_cs_gpio>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
+ uart6: serial@998000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00998000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- out-ports {
- port {
- swao_funnel_out: endpoint {
- remote-endpoint = <&etf_in>;
- };
- };
+ i2c7: i2c@99c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c7_data_clk>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+ <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
};
- in-ports {
+ spi7: spi@99c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>, <&qup_spi7_cs_gpio>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
- port@7 {
- reg = <7>;
- swao_funnel_in: endpoint {
- remote-endpoint = <&merge_funnel_out>;
- };
- };
+ uart7: serial@99c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0099c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
};
};
- etf@6b05000 {
- compatible = "arm,coresight-tmc", "arm,primecell";
- reg = <0 0x06b05000 0 0x1000>;
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x00ac0000 0 0x2000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ iommus = <&apps_smmu 0x43 0x0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
+ interconnect-names = "qup-core";
+ status = "disabled";
+
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c8_data_clk>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi8: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>, <&qup_spi8_cs_gpio>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart8: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>, <&qup_uart8_tx>, <&qup_uart8_rx>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_data_clk>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>, <&qup_spi9_cs_gpio>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart9: serial@a84000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>, <&qup_uart9_tx>, <&qup_uart9_rx>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_data_clk>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>, <&qup_spi10_cs_gpio>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart10: serial@a88000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>, <&qup_uart10_tx>, <&qup_uart10_rx>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_data_clk>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi11: spi@a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>, <&qup_spi11_cs_gpio>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart11: serial@a8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart11_cts>, <&qup_uart11_rts>, <&qup_uart11_tx>, <&qup_uart11_rx>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c12_data_clk>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>, <&qup_spi12_cs_gpio>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart12: serial@a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>, <&qup_uart12_tx>, <&qup_uart12_rx>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c13_data_clk>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi13: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>, <&qup_spi13_cs_gpio>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart13: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>, <&qup_uart13_tx>, <&qup_uart13_rx>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c14_data_clk>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi14: spi@a98000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>, <&qup_spi14_cs_gpio>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart14: serial@a98000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>, <&qup_uart14_tx>, <&qup_uart14_rx>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c15: i2c@a9c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c15_data_clk>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi15: spi@a9c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>, <&qup_spi15_cs_gpio>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart15: serial@a9c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>, <&qup_uart15_tx>, <&qup_uart15_rx>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+ };
+
+ stm@6002000 {
+ compatible = "arm,coresight-stm", "arm,primecell";
+ reg = <0 0x06002000 0 0x1000>,
+ <0 0x16280000 0 0x180000>;
+ reg-names = "stm-base", "stm-stimulus-base";
clocks = <&aoss_qmp>;
clock-names = "apb_pclk";
out-ports {
port {
- etf_out: endpoint {
- remote-endpoint = <&swao_replicator_in>;
- };
- };
- };
-
- in-ports {
- port {
- etf_in: endpoint {
- remote-endpoint = <&swao_funnel_out>;
+ stm_out: endpoint {
+ remote-endpoint = <&funnel0_in7>;
};
};
};
};
- replicator@6b06000 {
- compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
- reg = <0 0x06b06000 0 0x1000>;
+ funnel@6041000 {
+ compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+ reg = <0 0x06041000 0 0x1000>;
clocks = <&aoss_qmp>;
clock-names = "apb_pclk";
- qcom,replicator-loses-context;
out-ports {
port {
- swao_replicator_out: endpoint {
- remote-endpoint = <&replicator_in>;
+ funnel0_out: endpoint {
+ remote-endpoint = <&merge_funnel_in0>;
};
};
};
in-ports {
- port {
- swao_replicator_in: endpoint {
- remote-endpoint = <&etf_out>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@7 {
+ reg = <7>;
+ funnel0_in7: endpoint {
+ remote-endpoint = <&stm_out>;
};
};
};
};
- etm@7040000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07040000 0 0x1000>;
-
- cpu = <&CPU0>;
+ funnel@6042000 {
+ compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+ reg = <0 0x06042000 0 0x1000>;
clocks = <&aoss_qmp>;
clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
out-ports {
port {
- etm0_out: endpoint {
- remote-endpoint = <&apss_funnel_in0>;
+ funnel1_out: endpoint {
+ remote-endpoint = <&merge_funnel_in1>;
};
};
};
- };
- etm@7140000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07140000 0 0x1000>;
-
- cpu = <&CPU1>;
-
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
+ in-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- out-ports {
- port {
- etm1_out: endpoint {
- remote-endpoint = <&apss_funnel_in1>;
+ port@4 {
+ reg = <4>;
+ funnel1_in4: endpoint {
+ remote-endpoint = <&apss_merge_funnel_out>;
};
};
};
};
- etm@7240000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07240000 0 0x1000>;
-
- cpu = <&CPU2>;
+ funnel@6045000 {
+ compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+ reg = <0 0x06045000 0 0x1000>;
clocks = <&aoss_qmp>;
clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
out-ports {
port {
- etm2_out: endpoint {
+ merge_funnel_out: endpoint {
+ remote-endpoint = <&swao_funnel_in>;
+ };
+ };
+ };
+
+ in-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ merge_funnel_in0: endpoint {
+ remote-endpoint = <&funnel0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ merge_funnel_in1: endpoint {
+ remote-endpoint = <&funnel1_out>;
+ };
+ };
+ };
+ };
+
+ replicator@6046000 {
+ compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+ reg = <0 0x06046000 0 0x1000>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+
+ out-ports {
+ port {
+ replicator_out: endpoint {
+ remote-endpoint = <&etr_in>;
+ };
+ };
+ };
+
+ in-ports {
+ port {
+ replicator_in: endpoint {
+ remote-endpoint = <&swao_replicator_out>;
+ };
+ };
+ };
+ };
+
+ etr@6048000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x06048000 0 0x1000>;
+ iommus = <&apps_smmu 0x04c0 0>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,scatter-gather;
+
+ in-ports {
+ port {
+ etr_in: endpoint {
+ remote-endpoint = <&replicator_out>;
+ };
+ };
+ };
+ };
+
+ funnel@6b04000 {
+ compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+ reg = <0 0x06b04000 0 0x1000>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+
+ out-ports {
+ port {
+ swao_funnel_out: endpoint {
+ remote-endpoint = <&etf_in>;
+ };
+ };
+ };
+
+ in-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@7 {
+ reg = <7>;
+ swao_funnel_in: endpoint {
+ remote-endpoint = <&merge_funnel_out>;
+ };
+ };
+ };
+ };
+
+ etf@6b05000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x06b05000 0 0x1000>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+
+ out-ports {
+ port {
+ etf_out: endpoint {
+ remote-endpoint = <&swao_replicator_in>;
+ };
+ };
+ };
+
+ in-ports {
+ port {
+ etf_in: endpoint {
+ remote-endpoint = <&swao_funnel_out>;
+ };
+ };
+ };
+ };
+
+ replicator@6b06000 {
+ compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+ reg = <0 0x06b06000 0 0x1000>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ qcom,replicator-loses-context;
+
+ out-ports {
+ port {
+ swao_replicator_out: endpoint {
+ remote-endpoint = <&replicator_in>;
+ };
+ };
+ };
+
+ in-ports {
+ port {
+ swao_replicator_in: endpoint {
+ remote-endpoint = <&etf_out>;
+ };
+ };
+ };
+ };
+
+ etm@7040000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07040000 0 0x1000>;
+
+ cpu = <&CPU0>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm0_out: endpoint {
+ remote-endpoint = <&apss_funnel_in0>;
+ };
+ };
+ };
+ };
+
+ etm@7140000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07140000 0 0x1000>;
+
+ cpu = <&CPU1>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm1_out: endpoint {
+ remote-endpoint = <&apss_funnel_in1>;
+ };
+ };
+ };
+ };
+
+ etm@7240000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07240000 0 0x1000>;
+
+ cpu = <&CPU2>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm2_out: endpoint {
remote-endpoint = <&apss_funnel_in2>;
};
};
};
- };
+ };
+
+ etm@7340000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07340000 0 0x1000>;
+
+ cpu = <&CPU3>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm3_out: endpoint {
+ remote-endpoint = <&apss_funnel_in3>;
+ };
+ };
+ };
+ };
+
+ etm@7440000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07440000 0 0x1000>;
+
+ cpu = <&CPU4>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm4_out: endpoint {
+ remote-endpoint = <&apss_funnel_in4>;
+ };
+ };
+ };
+ };
+
+ etm@7540000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07540000 0 0x1000>;
+
+ cpu = <&CPU5>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm5_out: endpoint {
+ remote-endpoint = <&apss_funnel_in5>;
+ };
+ };
+ };
+ };
+
+ etm@7640000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07640000 0 0x1000>;
+
+ cpu = <&CPU6>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm6_out: endpoint {
+ remote-endpoint = <&apss_funnel_in6>;
+ };
+ };
+ };
+ };
+
+ etm@7740000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x07740000 0 0x1000>;
+
+ cpu = <&CPU7>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+ arm,coresight-loses-context-with-cpu;
+ qcom,skip-power-up;
+
+ out-ports {
+ port {
+ etm7_out: endpoint {
+ remote-endpoint = <&apss_funnel_in7>;
+ };
+ };
+ };
+ };
+
+ funnel@7800000 { /* APSS Funnel */
+ compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+ reg = <0 0x07800000 0 0x1000>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+
+ out-ports {
+ port {
+ apss_funnel_out: endpoint {
+ remote-endpoint = <&apss_merge_funnel_in>;
+ };
+ };
+ };
+
+ in-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ apss_funnel_in0: endpoint {
+ remote-endpoint = <&etm0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ apss_funnel_in1: endpoint {
+ remote-endpoint = <&etm1_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ apss_funnel_in2: endpoint {
+ remote-endpoint = <&etm2_out>;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ apss_funnel_in3: endpoint {
+ remote-endpoint = <&etm3_out>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ apss_funnel_in4: endpoint {
+ remote-endpoint = <&etm4_out>;
+ };
+ };
+
+ port@5 {
+ reg = <5>;
+ apss_funnel_in5: endpoint {
+ remote-endpoint = <&etm5_out>;
+ };
+ };
+
+ port@6 {
+ reg = <6>;
+ apss_funnel_in6: endpoint {
+ remote-endpoint = <&etm6_out>;
+ };
+ };
+
+ port@7 {
+ reg = <7>;
+ apss_funnel_in7: endpoint {
+ remote-endpoint = <&etm7_out>;
+ };
+ };
+ };
+ };
+
+ funnel@7810000 {
+ compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+ reg = <0 0x07810000 0 0x1000>;
+
+ clocks = <&aoss_qmp>;
+ clock-names = "apb_pclk";
+
+ out-ports {
+ port {
+ apss_merge_funnel_out: endpoint {
+ remote-endpoint = <&funnel1_in4>;
+ };
+ };
+ };
+
+ in-ports {
+ port {
+ apss_merge_funnel_in: endpoint {
+ remote-endpoint = <&apss_funnel_out>;
+ };
+ };
+ };
+ };
+
+ system-cache-controller@9200000 {
+ compatible = "qcom,sc7280-llcc";
+ reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>;
+ reg-names = "llcc_base", "llcc_broadcast_base";
+ interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pdc: interrupt-controller@b220000 {
+ compatible = "qcom,sc7280-pdc", "qcom,pdc";
+ reg = <0 0x0b220000 0 0x30000>;
+ qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>,
+ <55 306 4>, <59 312 3>, <62 374 2>,
+ <64 434 2>, <66 438 3>, <69 86 1>,
+ <70 520 54>, <124 609 31>, <155 63 1>,
+ <156 716 12>;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&intc>;
+ interrupt-controller;
+ };
+
+ aoss_qmp: power-controller@c300000 {
+ compatible = "qcom,sc7280-aoss-qmp";
+ reg = <0 0x0c300000 0 0x100000>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_AOP
+ IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_AOP
+ IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ #clock-cells = <0>;
+ #power-domain-cells = <1>;
+ };
+
+ spmi_bus: spmi@c440000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0 0x0c440000 0 0x1100>,
+ <0 0x0c600000 0 0x2000000>,
+ <0 0x0e600000 0 0x100000>,
+ <0 0x0e700000 0 0xa0000>,
+ <0 0x0c40a000 0 0x26000>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
+ tlmm: pinctrl@f100000 {
+ compatible = "qcom,sc7280-pinctrl";
+ reg = <0 0x0f100000 0 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 175>;
+ wakeup-parent = <&pdc>;
+
+ qspi_clk: qspi-clk {
+ pins = "gpio14";
+ function = "qspi_clk";
+ };
+
+ qspi_cs0: qspi-cs0 {
+ pins = "gpio15";
+ function = "qspi_cs";
+ };
+
+ qspi_cs1: qspi-cs1 {
+ pins = "gpio19";
+ function = "qspi_cs";
+ };
+
+ qspi_data01: qspi-data01 {
+ pins = "gpio12", "gpio13";
+ function = "qspi_data";
+ };
+
+ qspi_data12: qspi-data12 {
+ pins = "gpio16", "gpio17";
+ function = "qspi_data";
+ };
+
+ qup_i2c0_data_clk:qup-i2c0-data-clk {
+ pins = "gpio0", "gpio1";
+ function = "qup00";
+ };
+
+ qup_i2c1_data_clk:qup-i2c1-data-clk {
+ pins = "gpio4", "gpio5";
+ function = "qup01";
+ };
+
+ qup_i2c2_data_clk:qup-i2c2-data-clk {
+ pins = "gpio8", "gpio9";
+ function = "qup02";
+ };
+
+ qup_i2c3_data_clk:qup-i2c3-data-clk {
+ pins = "gpio12", "gpio13";
+ function = "qup03";
+ };
+
+ qup_i2c4_data_clk:qup-i2c4-data-clk {
+ pins = "gpio16", "gpio17";
+ function = "qup04";
+ };
+
+ qup_i2c5_data_clk:qup-i2c5-data-clk {
+ pins = "gpio20", "gpio21";
+ function = "qup05";
+ };
+
+ qup_i2c6_data_clk:qup-i2c6-data-clk {
+ pins = "gpio24", "gpio25";
+ function = "qup06";
+ };
+
+ qup_i2c7_data_clk:qup-i2c7-data-clk {
+ pins = "gpio28", "gpio29";
+ function = "qup07";
+ };
+
+ qup_i2c8_data_clk:qup-i2c8-data-clk {
+ pins = "gpio32", "gpio33";
+ function = "qup08";
+ };
+
+ qup_i2c9_data_clk:qup-i2c9-data-clk {
+ pins = "gpio36", "gpio37";
+ function = "qup09";
+ };
+
+ qup_i2c10_data_clk:qup-i2c10-data-clk {
+ pins = "gpio40", "gpio41";
+ function = "qup10";
+ };
+
+ qup_i2c11_data_clk:qup-i2c11-data-clk {
+ pins = "gpio44", "gpio45";
+ function = "qup11";
+ };
+
+ qup_i2c12_data_clk:qup-i2c12-data-clk {
+ pins = "gpio48", "gpio49";
+ function = "qup12";
+ };
+
+ qup_i2c13_data_clk:qup-i2c13-data-clk {
+ pins = "gpio52", "gpio53";
+ function = "qup13";
+ };
+
+ qup_i2c14_data_clk:qup-i2c14-data-clk {
+ pins = "gpio56", "gpio57";
+ function = "qup14";
+ };
+
+ qup_i2c15_data_clk:qup-i2c15-data-clk {
+ pins = "gpio60", "gpio61";
+ function = "qup15";
+ };
+
+ qup_spi0_data_clk: qup-spi0-data-clk {
+ pins = "gpio0", "gpio1", "gpio2";
+ function = "qup00";
+ };
+
+ qup_spi0_cs: qup-spi0-cs {
+ pins = "gpio3";
+ function = "qup00";
+ };
+
+ qup_spi0_cs_gpio: qup-spi0-cs_gpio {
+ pins = "gpio3";
+ function = "gpio";
+ };
+
+ qup_spi1_data_clk: qup-spi1-data-clk {
+ pins = "gpio4", "gpio5", "gpio6";
+ function = "qup01";
+ };
+
+ qup_spi1_cs: qup-spi1-cs {
+ pins = "gpio7";
+ function = "qup01";
+ };
+
+ qup_spi1_cs_gpio: qup-spi1-cs_gpio {
+ pins = "gpio7";
+ function = "gpio";
+ };
+
+ qup_spi2_data_clk: qup-spi2-data-clk {
+ pins = "gpio8", "gpio9", "gpio10";
+ function = "qup02";
+ };
+
+ qup_spi2_cs: qup-spi2-cs {
+ pins = "gpio11";
+ function = "qup02";
+ };
+
+ qup_spi2_cs_gpio: qup-spi2-cs_gpio {
+ pins = "gpio11";
+ function = "gpio";
+ };
+
+ qup_spi3_data_clk: qup-spi3-data-clk {
+ pins = "gpio12", "gpio13", "gpio14";
+ function = "qup03";
+ };
+
+ qup_spi3_cs: qup-spi3-cs {
+ pins = "gpio15";
+ function = "qup03";
+ };
+
+ qup_spi3_cs_gpio: qup-spi3-cs_gpio {
+ pins = "gpio15";
+ function = "gpio";
+ };
+
+ qup_spi4_data_clk: qup-spi4-data-clk {
+ pins = "gpio16", "gpio17", "gpio18";
+ function = "qup04";
+ };
+
+ qup_spi4_cs: qup-spi4-cs {
+ pins = "gpio19";
+ function = "qup04";
+ };
+
+ qup_spi4_cs_gpio: qup-spi4-cs_gpio {
+ pins = "gpio19";
+ function = "gpio";
+ };
+
+ qup_spi5_data_clk: qup-spi5-data-clk {
+ pins = "gpio20", "gpio21", "gpio22";
+ function = "qup05";
+ };
+
+ qup_spi5_cs: qup-spi5-cs {
+ pins = "gpio23";
+ function = "qup05";
+ };
+
+ qup_spi5_cs_gpio: qup-spi5-cs_gpio {
+ pins = "gpio23";
+ function = "gpio";
+ };
+
+ qup_spi6_data_clk: qup-spi6-data-clk {
+ pins = "gpio24", "gpio25", "gpio26";
+ function = "qup06";
+ };
+
+ qup_spi6_cs: qup-spi6-cs {
+ pins = "gpio27";
+ function = "qup06";
+ };
+
+ qup_spi6_cs_gpio: qup-spi6-cs_gpio {
+ pins = "gpio27";
+ function = "gpio";
+ };
+
+ qup_spi7_data_clk: qup-spi7-data-clk {
+ pins = "gpio28", "gpio29", "gpio30";
+ function = "qup07";
+ };
+
+ qup_spi7_cs: qup-spi7-cs {
+ pins = "gpio31";
+ function = "qup07";
+ };
+
+ qup_spi7_cs_gpio: qup-spi7-cs_gpio {
+ pins = "gpio31";
+ function = "gpio";
+ };
+
+ qup_spi8_data_clk: qup-spi8-data-clk {
+ pins = "gpio32", "gpio33", "gpio34";
+ function = "qup08";
+ };
+
+ qup_spi8_cs: qup-spi8-cs {
+ pins = "gpio35";
+ function = "qup08";
+ };
+
+ qup_spi8_cs_gpio: qup-spi8-cs_gpio {
+ pins = "gpio35";
+ function = "gpio";
+ };
+
+ qup_spi9_data_clk: qup-spi9-data-clk {
+ pins = "gpio36", "gpio37", "gpio38";
+ function = "qup09";
+ };
+
+ qup_spi9_cs: qup-spi9-cs {
+ pins = "gpio39";
+ function = "qup09";
+ };
+
+ qup_spi9_cs_gpio: qup-spi9-cs_gpio {
+ pins = "gpio39";
+ function = "gpio";
+ };
+
+ qup_spi10_data_clk: qup-spi10-data-clk {
+ pins = "gpio40", "gpio41", "gpio42";
+ function = "qup10";
+ };
+
+ qup_spi10_cs: qup-spi10-cs {
+ pins = "gpio43";
+ function = "qup10";
+ };
+
+ qup_spi10_cs_gpio: qup-spi10-cs_gpio {
+ pins = "gpio43";
+ function = "gpio";
+ };
+
+ qup_spi11_data_clk: qup-spi11-data-clk {
+ pins = "gpio44", "gpio45", "gpio46";
+ function = "qup11";
+ };
+
+ qup_spi11_cs: qup-spi11-cs {
+ pins = "gpio47";
+ function = "qup11";
+ };
+
+ qup_spi11_cs_gpio: qup-spi11-cs_gpio {
+ pins = "gpio47";
+ function = "gpio";
+ };
+
+ qup_spi12_data_clk: qup-spi12-data-clk {
+ pins = "gpio48", "gpio49", "gpio50";
+ function = "qup12";
+ };
+
+ qup_spi12_cs: qup-spi12-cs {
+ pins = "gpio51";
+ function = "qup12";
+ };
+
+ qup_spi12_cs_gpio: qup-spi12-cs_gpio {
+ pins = "gpio51";
+ function = "gpio";
+ };
+
+ qup_spi13_data_clk: qup-spi13-data-clk {
+ pins = "gpio52", "gpio53", "gpio54";
+ function = "qup13";
+ };
+
+ qup_spi13_cs: qup-spi13-cs {
+ pins = "gpio55";
+ function = "qup13";
+ };
+
+ qup_spi13_cs_gpio: qup-spi13-cs_gpio {
+ pins = "gpio55";
+ function = "gpio";
+ };
+
+ qup_spi14_data_clk: qup-spi14-data-clk {
+ pins = "gpio56", "gpio57", "gpio58";
+ function = "qup14";
+ };
+
+ qup_spi14_cs: qup-spi14-cs {
+ pins = "gpio59";
+ function = "qup14";
+ };
+
+ qup_spi14_cs_gpio: qup-spi14-cs_gpio {
+ pins = "gpio59";
+ function = "gpio";
+ };
+
+ qup_spi15_data_clk: qup-spi15-data-clk {
+ pins = "gpio60", "gpio61", "gpio62";
+ function = "qup15";
+ };
+
+ qup_spi15_cs: qup-spi15-cs {
+ pins = "gpio63";
+ function = "qup15";
+ };
+
+ qup_spi15_cs_gpio: qup-spi15-cs_gpio {
+ pins = "gpio63";
+ function = "gpio";
+ };
+
+ qup_uart0_cts: qup-uart0-cts {
+ pins = "gpio0";
+ function = "qup00";
+ };
+
+ qup_uart0_rts: qup-uart0-rts {
+ pins = "gpio1";
+ function = "qup00";
+ };
+
+ qup_uart0_tx: qup-uart0-tx {
+ pins = "gpio2";
+ function = "qup00";
+ };
+
+ qup_uart0_rx: qup-uart0-rx {
+ pins = "gpio3";
+ function = "qup00";
+ };
+
+ qup_uart1_cts: qup-uart1-cts {
+ pins = "gpio4";
+ function = "qup01";
+ };
+
+ qup_uart1_rts: qup-uart1-rts {
+ pins = "gpio5";
+ function = "qup01";
+ };
+
+ qup_uart1_tx: qup-uart1-tx {
+ pins = "gpio6";
+ function = "qup01";
+ };
+
+ qup_uart1_rx: qup-uart1-rx {
+ pins = "gpio7";
+ function = "qup01";
+ };
+
+ qup_uart2_cts: qup-uart2-cts {
+ pins = "gpio8";
+ function = "qup02";
+ };
+
+ qup_uart2_rts: qup-uart2-rts {
+ pins = "gpio9";
+ function = "qup02";
+ };
+
+ qup_uart2_tx: qup-uart2-tx {
+ pins = "gpio10";
+ function = "qup02";
+ };
+
+ qup_uart2_rx: qup-uart2-rx {
+ pins = "gpio11";
+ function = "qup02";
+ };
+
+ qup_uart3_cts: qup-uart3-cts {
+ pins = "gpio12";
+ function = "qup03";
+ };
+
+ qup_uart3_rts: qup-uart3-rts {
+ pins = "gpio13";
+ function = "qup03";
+ };
+
+ qup_uart3_tx: qup-uart3-tx {
+ pins = "gpio14";
+ function = "qup03";
+ };
+
+ qup_uart3_rx: qup-uart3-rx {
+ pins = "gpio15";
+ function = "qup03";
+ };
+
+ qup_uart4_cts: qup-uart4-cts {
+ pins = "gpio16";
+ function = "qup04";
+ };
+
+ qup_uart4_rts: qup-uart4-rts {
+ pins = "gpio17";
+ function = "qup04";
+ };
+
+ qup_uart4_tx: qup-uart4-tx {
+ pins = "gpio18";
+ function = "qup04";
+ };
+
+ qup_uart4_rx: qup-uart4-rx {
+ pins = "gpio19";
+ function = "qup04";
+ };
+
+ qup_uart5_cts: qup-uart5-cts {
+ pins = "gpio20";
+ function = "qup05";
+ };
+
+ qup_uart5_rts: qup-uart5-rts {
+ pins = "gpio21";
+ function = "qup05";
+ };
+
+ qup_uart5_tx: qup-uart5-tx {
+ pins = "gpio22";
+ function = "qup05";
+ };
+
+ qup_uart5_rx: qup-uart5-rx {
+ pins = "gpio23";
+ function = "qup05";
+ };
- etm@7340000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07340000 0 0x1000>;
+ qup_uart6_cts: qup-uart6-cts {
+ pins = "gpio24";
+ function = "qup06";
+ };
- cpu = <&CPU3>;
+ qup_uart6_rts: qup-uart6-rts {
+ pins = "gpio25";
+ function = "qup06";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
+ qup_uart6_tx: qup-uart6-tx {
+ pins = "gpio26";
+ function = "qup06";
+ };
- out-ports {
- port {
- etm3_out: endpoint {
- remote-endpoint = <&apss_funnel_in3>;
- };
- };
+ qup_uart6_rx: qup-uart6-rx {
+ pins = "gpio27";
+ function = "qup06";
};
- };
- etm@7440000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07440000 0 0x1000>;
+ qup_uart7_cts: qup-uart7-cts {
+ pins = "gpio28";
+ function = "qup07";
+ };
- cpu = <&CPU4>;
+ qup_uart7_rts: qup-uart7-rts {
+ pins = "gpio29";
+ function = "qup07";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
+ qup_uart7_tx: qup-uart7-tx {
+ pins = "gpio30";
+ function = "qup07";
+ };
- out-ports {
- port {
- etm4_out: endpoint {
- remote-endpoint = <&apss_funnel_in4>;
- };
- };
+ qup_uart7_rx: qup-uart7-rx {
+ pins = "gpio31";
+ function = "qup07";
};
- };
- etm@7540000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07540000 0 0x1000>;
+ qup_uart8_cts: qup-uart8-cts {
+ pins = "gpio32";
+ function = "qup08";
+ };
- cpu = <&CPU5>;
+ qup_uart8_rts: qup-uart8-rts {
+ pins = "gpio33";
+ function = "qup08";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
+ qup_uart8_tx: qup-uart8-tx {
+ pins = "gpio34";
+ function = "qup08";
+ };
- out-ports {
- port {
- etm5_out: endpoint {
- remote-endpoint = <&apss_funnel_in5>;
- };
- };
+ qup_uart8_rx: qup-uart8-rx {
+ pins = "gpio35";
+ function = "qup08";
};
- };
- etm@7640000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07640000 0 0x1000>;
+ qup_uart9_cts: qup-uart9-cts {
+ pins = "gpio36";
+ function = "qup09";
+ };
- cpu = <&CPU6>;
+ qup_uart9_rts: qup-uart9-rts {
+ pins = "gpio37";
+ function = "qup09";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
+ qup_uart9_tx: qup-uart9-tx {
+ pins = "gpio38";
+ function = "qup09";
+ };
- out-ports {
- port {
- etm6_out: endpoint {
- remote-endpoint = <&apss_funnel_in6>;
- };
- };
+ qup_uart9_rx: qup-uart9-rx {
+ pins = "gpio39";
+ function = "qup09";
};
- };
- etm@7740000 {
- compatible = "arm,coresight-etm4x", "arm,primecell";
- reg = <0 0x07740000 0 0x1000>;
+ qup_uart10_cts: qup-uart10-cts {
+ pins = "gpio40";
+ function = "qup10";
+ };
- cpu = <&CPU7>;
+ qup_uart10_rts: qup-uart10-rts {
+ pins = "gpio41";
+ function = "qup10";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
- arm,coresight-loses-context-with-cpu;
- qcom,skip-power-up;
+ qup_uart10_tx: qup-uart10-tx {
+ pins = "gpio42";
+ function = "qup10";
+ };
- out-ports {
- port {
- etm7_out: endpoint {
- remote-endpoint = <&apss_funnel_in7>;
- };
- };
+ qup_uart10_rx: qup-uart10-rx {
+ pins = "gpio43";
+ function = "qup10";
};
- };
- funnel@7800000 { /* APSS Funnel */
- compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
- reg = <0 0x07800000 0 0x1000>;
+ qup_uart11_cts: qup-uart11-cts {
+ pins = "gpio44";
+ function = "qup11";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
+ qup_uart11_rts: qup-uart11-rts {
+ pins = "gpio45";
+ function = "qup11";
+ };
- out-ports {
- port {
- apss_funnel_out: endpoint {
- remote-endpoint = <&apss_merge_funnel_in>;
- };
- };
+ qup_uart11_tx: qup-uart11-tx {
+ pins = "gpio46";
+ function = "qup11";
};
- in-ports {
- #address-cells = <1>;
- #size-cells = <0>;
+ qup_uart11_rx: qup-uart11-rx {
+ pins = "gpio47";
+ function = "qup11";
+ };
- port@0 {
- reg = <0>;
- apss_funnel_in0: endpoint {
- remote-endpoint = <&etm0_out>;
- };
- };
+ qup_uart12_cts: qup-uart12-cts {
+ pins = "gpio48";
+ function = "qup12";
+ };
- port@1 {
- reg = <1>;
- apss_funnel_in1: endpoint {
- remote-endpoint = <&etm1_out>;
- };
- };
+ qup_uart12_rts: qup-uart12-rts {
+ pins = "gpio49";
+ function = "qup12";
+ };
- port@2 {
- reg = <2>;
- apss_funnel_in2: endpoint {
- remote-endpoint = <&etm2_out>;
- };
- };
+ qup_uart12_tx: qup-uart12-tx {
+ pins = "gpio50";
+ function = "qup12";
+ };
- port@3 {
- reg = <3>;
- apss_funnel_in3: endpoint {
- remote-endpoint = <&etm3_out>;
- };
- };
+ qup_uart12_rx: qup-uart12-rx {
+ pins = "gpio51";
+ function = "qup12";
+ };
- port@4 {
- reg = <4>;
- apss_funnel_in4: endpoint {
- remote-endpoint = <&etm4_out>;
- };
- };
+ qup_uart13_cts: qup-uart13-cts {
+ pins = "gpio52";
+ function = "qup13";
+ };
- port@5 {
- reg = <5>;
- apss_funnel_in5: endpoint {
- remote-endpoint = <&etm5_out>;
- };
- };
+ qup_uart13_rts: qup-uart13-rts {
+ pins = "gpio53";
+ function = "qup13";
+ };
- port@6 {
- reg = <6>;
- apss_funnel_in6: endpoint {
- remote-endpoint = <&etm6_out>;
- };
- };
+ qup_uart13_tx: qup-uart13-tx {
+ pins = "gpio54";
+ function = "qup13";
+ };
- port@7 {
- reg = <7>;
- apss_funnel_in7: endpoint {
- remote-endpoint = <&etm7_out>;
- };
- };
+ qup_uart13_rx: qup-uart13-rx {
+ pins = "gpio55";
+ function = "qup13";
};
- };
- funnel@7810000 {
- compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
- reg = <0 0x07810000 0 0x1000>;
+ qup_uart14_cts: qup-uart14-cts {
+ pins = "gpio56";
+ function = "qup14";
+ };
- clocks = <&aoss_qmp>;
- clock-names = "apb_pclk";
+ qup_uart14_rts: qup-uart14-rts {
+ pins = "gpio57";
+ function = "qup14";
+ };
- out-ports {
- port {
- apss_merge_funnel_out: endpoint {
- remote-endpoint = <&funnel1_in4>;
- };
- };
+ qup_uart14_tx: qup-uart14-tx {
+ pins = "gpio58";
+ function = "qup14";
};
- in-ports {
- port {
- apss_merge_funnel_in: endpoint {
- remote-endpoint = <&apss_funnel_out>;
- };
- };
+ qup_uart14_rx: qup-uart14-rx {
+ pins = "gpio59";
+ function = "qup14";
};
- };
- system-cache-controller@9200000 {
- compatible = "qcom,sc7280-llcc";
- reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>;
- reg-names = "llcc_base", "llcc_broadcast_base";
- interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
- };
+ qup_uart15_cts: qup-uart15-cts {
+ pins = "gpio60";
+ function = "qup15";
+ };
- pdc: interrupt-controller@b220000 {
- compatible = "qcom,sc7280-pdc", "qcom,pdc";
- reg = <0 0x0b220000 0 0x30000>;
- qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>,
- <55 306 4>, <59 312 3>, <62 374 2>,
- <64 434 2>, <66 438 3>, <69 86 1>,
- <70 520 54>, <124 609 31>, <155 63 1>,
- <156 716 12>;
- #interrupt-cells = <2>;
- interrupt-parent = <&intc>;
- interrupt-controller;
- };
+ qup_uart15_rts: qup-uart15-rts {
+ pins = "gpio61";
+ function = "qup15";
+ };
- aoss_qmp: power-controller@c300000 {
- compatible = "qcom,sc7280-aoss-qmp";
- reg = <0 0x0c300000 0 0x100000>;
- interrupts-extended = <&ipcc IPCC_CLIENT_AOP
- IPCC_MPROC_SIGNAL_GLINK_QMP
- IRQ_TYPE_EDGE_RISING>;
- mboxes = <&ipcc IPCC_CLIENT_AOP
- IPCC_MPROC_SIGNAL_GLINK_QMP>;
+ qup_uart15_tx: qup-uart15-tx {
+ pins = "gpio62";
+ function = "qup15";
+ };
- #clock-cells = <0>;
- #power-domain-cells = <1>;
- };
+ qup_uart15_rx: qup-uart15-rx {
+ pins = "gpio63";
+ function = "qup15";
+ };
- spmi_bus: spmi@c440000 {
- compatible = "qcom,spmi-pmic-arb";
- reg = <0 0x0c440000 0 0x1100>,
- <0 0x0c600000 0 0x2000000>,
- <0 0x0e600000 0 0x100000>,
- <0 0x0e700000 0 0xa0000>,
- <0 0x0c40a000 0 0x26000>;
- reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
- interrupt-names = "periph_irq";
- interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
- qcom,ee = <0>;
- qcom,channel = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- interrupt-controller;
- #interrupt-cells = <4>;
};
- tlmm: pinctrl@f100000 {
- compatible = "qcom,sc7280-pinctrl";
- reg = <0 0x0f100000 0 0x300000>;
- interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-ranges = <&tlmm 0 0 175>;
- wakeup-parent = <&pdc>;
+ qspi_opp_table: qspi-opp-table {
+ compatible = "operating-points-v2";
- qup_uart5_default: qup-uart5-default {
- pins = "gpio46", "gpio47";
- function = "qup13";
+ opp-75000000 {
+ opp-hz = /bits/ 64 <75000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
};
+
+ opp-150000000 {
+ opp-hz = /bits/ 64 <150000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
+ qspi: spi@88dc000 {
+ compatible = "qcom,qspi-v1";
+ reg = <0 0x088dc000 0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <&gcc GCC_QSPI_CORE_CLK>;
+ clock-names = "iface", "core";
+ interconnects = <&gem_noc MASTER_APPSS_PROC 0
+ &cnoc2 SLAVE_QSPI_0 0>;
+ interconnect-names = "qspi-config";
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qspi_opp_table>;
+ status = "disabled";
};
apps_smmu: iommu@15000000 {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next reply other threads:[~2021-04-22 15:06 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-22 15:05 Roja Rani Yarubandi [this message]
2021-04-22 21:22 ` [PATCH V2] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes kernel test robot
2021-04-22 21:22 ` kernel test robot
2021-04-23 9:46 ` rojay
2021-04-23 9:46 ` rojay
2021-05-25 9:19 ` [kbuild-all] " Rong Chen
2021-05-25 9:19 ` Rong Chen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210422150556.450-1-rojay@codeaurora.org \
--to=rojay@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=msavaliy@qti.qualcomm.com \
--cc=rnayak@codeaurora.org \
--cc=robh+dt@kernel.org \
--cc=saiprakash.ranjan@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.