From: Jerome Brunet <jbrunet@baylibre.com> To: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com>, linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org Subject: [PATCH] arm64: dts: meson: vim3: enable hdmi audio loopback Date: Thu, 29 Apr 2021 10:42:53 +0200 [thread overview] Message-ID: <20210429084253.59692-1-jbrunet@baylibre.com> (raw) Enable audio capture frontends and a tdm decoder. This makes it possible to loopback the audio played on the hdmi codec, which is the only output interface at the moment. Of course, one TODDR device would be enough to do that but since the 3 FRDDRs are enabled on the playback side, let's do the same on the capture side. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- .../boot/dts/amlogic/meson-khadas-vim3.dtsi | 41 +++++++++++++++++-- .../dts/amlogic/meson-sm1-khadas-vim3l.dts | 13 ++++++ 2 files changed, 50 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi index 66d67524b031..3cf4ecb6d52e 100644 --- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi @@ -171,11 +171,16 @@ hdmi_connector_in: endpoint { sound { compatible = "amlogic,axg-sound-card"; model = "KHADAS-VIM3"; - audio-aux-devs = <&tdmout_a>; + audio-aux-devs = <&tdmin_a>, <&tdmout_a>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", "TDMOUT_A IN 1", "FRDDR_B OUT 0", "TDMOUT_A IN 2", "FRDDR_C OUT 0", - "TDM_A Playback", "TDMOUT_A OUT"; + "TDM_A Playback", "TDMOUT_A OUT", + "TDMIN_A IN 0", "TDM_A Capture", + "TDMIN_A IN 3", "TDM_A Loopback", + "TODDR_A IN 0", "TDMIN_A OUT", + "TODDR_B IN 0", "TDMIN_A OUT", + "TODDR_C IN 0", "TDMIN_A OUT"; assigned-clocks = <&clkc CLKID_MPLL2>, <&clkc CLKID_MPLL0>, @@ -198,8 +203,20 @@ dai-link-2 { sound-dai = <&frddr_c>; }; - /* 8ch hdmi interface */ dai-link-3 { + sound-dai = <&toddr_a>; + }; + + dai-link-4 { + sound-dai = <&toddr_b>; + }; + + dai-link-5 { + sound-dai = <&toddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-6 { sound-dai = <&tdmif_a>; dai-format = "i2s"; dai-tdm-slot-tx-mask-0 = <1 1>; @@ -214,7 +231,7 @@ codec { }; /* hdmi glue */ - dai-link-4 { + dai-link-7 { sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; codec { @@ -454,10 +471,26 @@ &tdmif_a { status = "okay"; }; +&tdmin_a { + status = "okay"; +}; + &tdmout_a { status = "okay"; }; +&toddr_a { + status = "okay"; +}; + +&toddr_b { + status = "okay"; +}; + +&toddr_c { + status = "okay"; +}; + &tohdmitx { status = "okay"; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts index 06de0b1ce726..f2c098143594 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts @@ -32,6 +32,19 @@ vddcpu: regulator-vddcpu { regulator-boot-on; regulator-always-on; }; + + sound { + model = "G12B-KHADAS-VIM3L"; + audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", + "TDMOUT_A IN 1", "FRDDR_B OUT 0", + "TDMOUT_A IN 2", "FRDDR_C OUT 0", + "TDM_A Playback", "TDMOUT_A OUT", + "TDMIN_A IN 0", "TDM_A Capture", + "TDMIN_A IN 13", "TDM_A Loopback", + "TODDR_A IN 0", "TDMIN_A OUT", + "TODDR_B IN 0", "TDMIN_A OUT", + "TODDR_C IN 0", "TDMIN_A OUT"; + }; }; &cpu0 { -- 2.31.1
WARNING: multiple messages have this Message-ID (diff)
From: Jerome Brunet <jbrunet@baylibre.com> To: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com>, linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org Subject: [PATCH] arm64: dts: meson: vim3: enable hdmi audio loopback Date: Thu, 29 Apr 2021 10:42:53 +0200 [thread overview] Message-ID: <20210429084253.59692-1-jbrunet@baylibre.com> (raw) Enable audio capture frontends and a tdm decoder. This makes it possible to loopback the audio played on the hdmi codec, which is the only output interface at the moment. Of course, one TODDR device would be enough to do that but since the 3 FRDDRs are enabled on the playback side, let's do the same on the capture side. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- .../boot/dts/amlogic/meson-khadas-vim3.dtsi | 41 +++++++++++++++++-- .../dts/amlogic/meson-sm1-khadas-vim3l.dts | 13 ++++++ 2 files changed, 50 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi index 66d67524b031..3cf4ecb6d52e 100644 --- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi @@ -171,11 +171,16 @@ hdmi_connector_in: endpoint { sound { compatible = "amlogic,axg-sound-card"; model = "KHADAS-VIM3"; - audio-aux-devs = <&tdmout_a>; + audio-aux-devs = <&tdmin_a>, <&tdmout_a>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", "TDMOUT_A IN 1", "FRDDR_B OUT 0", "TDMOUT_A IN 2", "FRDDR_C OUT 0", - "TDM_A Playback", "TDMOUT_A OUT"; + "TDM_A Playback", "TDMOUT_A OUT", + "TDMIN_A IN 0", "TDM_A Capture", + "TDMIN_A IN 3", "TDM_A Loopback", + "TODDR_A IN 0", "TDMIN_A OUT", + "TODDR_B IN 0", "TDMIN_A OUT", + "TODDR_C IN 0", "TDMIN_A OUT"; assigned-clocks = <&clkc CLKID_MPLL2>, <&clkc CLKID_MPLL0>, @@ -198,8 +203,20 @@ dai-link-2 { sound-dai = <&frddr_c>; }; - /* 8ch hdmi interface */ dai-link-3 { + sound-dai = <&toddr_a>; + }; + + dai-link-4 { + sound-dai = <&toddr_b>; + }; + + dai-link-5 { + sound-dai = <&toddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-6 { sound-dai = <&tdmif_a>; dai-format = "i2s"; dai-tdm-slot-tx-mask-0 = <1 1>; @@ -214,7 +231,7 @@ codec { }; /* hdmi glue */ - dai-link-4 { + dai-link-7 { sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; codec { @@ -454,10 +471,26 @@ &tdmif_a { status = "okay"; }; +&tdmin_a { + status = "okay"; +}; + &tdmout_a { status = "okay"; }; +&toddr_a { + status = "okay"; +}; + +&toddr_b { + status = "okay"; +}; + +&toddr_c { + status = "okay"; +}; + &tohdmitx { status = "okay"; }; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts index 06de0b1ce726..f2c098143594 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts @@ -32,6 +32,19 @@ vddcpu: regulator-vddcpu { regulator-boot-on; regulator-always-on; }; + + sound { + model = "G12B-KHADAS-VIM3L"; + audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", + "TDMOUT_A IN 1", "FRDDR_B OUT 0", + "TDMOUT_A IN 2", "FRDDR_C OUT 0", + "TDM_A Playback", "TDMOUT_A OUT", + "TDMIN_A IN 0", "TDM_A Capture", + "TDMIN_A IN 13", "TDM_A Loopback", + "TODDR_A IN 0", "TDMIN_A OUT", + "TODDR_B IN 0", "TDMIN_A OUT", + "TODDR_C IN 0", "TDMIN_A OUT"; + }; }; &cpu0 { -- 2.31.1 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic
next reply other threads:[~2021-04-29 8:43 UTC|newest] Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-04-29 8:42 Jerome Brunet [this message] 2021-04-29 8:42 ` [PATCH] arm64: dts: meson: vim3: enable hdmi audio loopback Jerome Brunet 2021-04-29 9:10 ` Neil Armstrong 2021-04-29 9:10 ` Neil Armstrong 2021-05-04 0:05 ` Kevin Hilman 2021-05-04 0:05 ` Kevin Hilman
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210429084253.59692-1-jbrunet@baylibre.com \ --to=jbrunet@baylibre.com \ --cc=devicetree@vger.kernel.org \ --cc=khilman@baylibre.com \ --cc=linux-amlogic@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.