[PATCH 7/8] arm64: dts: qcom: pmm8155au_2: Add base dts file

[Bhupesh Sharma <bhupesh.sharma@linaro.org>]

Add base DTS file for pmm8155au_2 along with GPIOs, power-on, rtc and vadc
nodes.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: bhupesh.linux@gmail.com
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
 arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi | 107 ++++++++++++++++++++++
 1 file changed, 107 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
new file mode 100644
index 000000000000..11c0c203a4e2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmm8155au-2-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmm8155au_2_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmic@4 {
+		compatible = "qcom,pmm8155au-2", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+
+			status = "disabled";
+		};
+
+		pmm8155au_2_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmm8155au_2_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pmm8155au_2_gpios: gpio@c000 {
+			compatible = "qcom,pmm8155au-2-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@5 {
+		compatible = "qcom,pmm8155au-2", "qcom,spmi-pmic";
+		reg = <0x5 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
-- 
2.31.1