From: Konrad Dybcio <konrad.dybcio@somainline.org>
To: ~postmarketos/upstreaming@lists.sr.ht
Cc: martin.botka@somainline.org,
angelogioacchino.delregno@somainline.org,
marijn.suijten@somainline.org, jamipkettunen@somainline.org,
Konrad Dybcio <konrad.dybcio@somainline.org>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Kees Cook <keescook@chromium.org>,
Anton Vorontsov <anton@enomsg.org>,
Colin Cross <ccross@android.com>, Tony Luck <tony.luck@intel.com>
Subject: [PATCH v4 4/4] arm64: dts: qcom: Add support for SONY Xperia X Performance / XZ / XZs (msm8996, Tone platform)
Date: Tue, 8 Jun 2021 22:21:42 +0200 [thread overview]
Message-ID: <20210608202143.247427-4-konrad.dybcio@somainline.org> (raw)
In-Reply-To: <20210608202143.247427-1-konrad.dybcio@somainline.org>
From: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Add support for following boards:
- Xperia X Performance (dora)
- Xperia XZ (kagura)
- Xperia XZs (keyaki)
They are all based on the SONY Tone platform and feature largely similar hardware
with the most obvious differences being lack of USB-C and ToF sensor on Dora and
different camera sensor on Keyaki.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
Changes since v3:
- Disable HDMI/PHY instead of deleting their nodes
- Change tvdd-regulator gpio state to LOW
arch/arm64/boot/dts/qcom/Makefile | 6 +
.../msm8996-pmi8996-sony-xperia-tone-dora.dts | 11 +
...sm8996-pmi8996-sony-xperia-tone-kagura.dts | 11 +
...sm8996-pmi8996-sony-xperia-tone-keyaki.dts | 11 +
.../qcom/msm8996-sony-xperia-tone-dora.dts | 27 +
.../qcom/msm8996-sony-xperia-tone-kagura.dts | 15 +
.../qcom/msm8996-sony-xperia-tone-keyaki.dts | 26 +
.../dts/qcom/msm8996-sony-xperia-tone.dtsi | 956 ++++++++++++++++++
arch/arm64/boot/dts/qcom/msm8996.dtsi | 12 +-
9 files changed, 1069 insertions(+), 6 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f4e40589dbb5..3e2ac2365798 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -27,6 +27,12 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-satsuki.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-sumire.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-suzuran.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-pmi8996-sony-xperia-tone-dora.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-pmi8996-sony-xperia-tone-kagura.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-pmi8996-sony-xperia-tone-keyaki.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-dora.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-kagura.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-keyaki.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts
new file mode 100644
index 000000000000..b018693600a5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include "msm8996-sony-xperia-tone-dora.dts"
+#include "pmi8996.dtsi"
+
+/ {
+ model = "Sony Xperia X Performance (PMI8996)";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts
new file mode 100644
index 000000000000..842ea3cf557e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include "msm8996-sony-xperia-tone-kagura.dts"
+#include "pmi8996.dtsi"
+
+/ {
+ model = "Sony Xperia XZ (PMI8996)";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts
new file mode 100644
index 000000000000..b3f9062da4b0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include "msm8996-sony-xperia-tone-keyaki.dts"
+#include "pmi8996.dtsi"
+
+/ {
+ model = "Sony Xperia XZs (PMI8996)";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts
new file mode 100644
index 000000000000..b4cca54dcb68
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8996-sony-xperia-tone.dtsi"
+
+/ {
+ model = "Sony Xperia X Performance";
+ compatible = "sony,dora-row", "qcom,msm8996";
+};
+
+/delete-node/ &tof_sensor;
+/delete-node/ &pm8994_l11;
+/delete-node/ &pm8994_l14;
+
+&usb_detect {
+ pins = "gpio24";
+};
+
+&usb3_id {
+ id-gpio = <&tlmm 24 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts
new file mode 100644
index 000000000000..be6ea855fcce
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8996-sony-xperia-tone.dtsi"
+
+/ {
+ model = "Sony Xperia XZ";
+ compatible = "sony,kagura-row", "qcom,msm8996";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts
new file mode 100644
index 000000000000..1eee7d0fc178
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8996-sony-xperia-tone.dtsi"
+
+/ {
+ model = "Sony Xperia XZs";
+ compatible = "sony,keyaki-row", "qcom,msm8996";
+};
+
+&pm8994_l19 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+};
+
+&pm8994_l30 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-pull-down;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
new file mode 100644
index 000000000000..913d976cb3ab
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
@@ -0,0 +1,956 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include "msm8996.dtsi"
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+/delete-node/ &slpi_region;
+/delete-node/ &venus_region;
+/delete-node/ &zap_shader_region;
+
+/ {
+ qcom,msm-id = <246 0x30001>; /* MSM8996 V3.1 (Final) */
+ qcom,pmic-id = <0x20009 0x2000a 0 0>; /* PM8994 + PMI8994 */
+ qcom,board-id = <8 0>;
+
+ chosen {
+ /*
+ * Due to an unknown-for-a-few-years regression,
+ * SDHCI only works on MSM8996 in PIO (lame) mode.
+ */
+ bootargs = "sdhci.debug_quirks=0x40 sdhci.debug_quirks2=0x4 maxcpus=2";
+ };
+
+ reserved-memory {
+ ramoops@a7f00000 {
+ compatible = "ramoops";
+ reg = <0 0xa7f00000 0 0x100000>;
+ record-size = <0x20000>;
+ console-size = <0x40000>;
+ ftrace-size = <0x20000>;
+ pmsg-size = <0x20000>;
+ ecc-size = <16>;
+ };
+
+ cont_splash_mem: memory@83401000 {
+ reg = <0 0x83401000 0 0x23ff000>;
+ no-map;
+ };
+
+ zap_shader_region: gpu@90400000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x90400000 0x0 0x2000>;
+ no-map;
+ };
+
+ slpi_region: memory@90500000 {
+ reg = <0 0x90500000 0 0xa00000>;
+ no-map;
+ };
+
+ venus_region: memory@90f00000 {
+ reg = <0 0x90f00000 0 0x500000>;
+ no-map;
+ };
+ };
+
+ panel_tvdd: tvdd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "panel_tvdd";
+ gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&tp_vddio_en>;
+ pinctrl-names = "default";
+ };
+
+ usb3_id: usb3-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&tlmm 25 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_detect>;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-name = "vph_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ wlan_en: wlan-en-1-8v {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wl_reg_on>;
+
+ /* WLAN card specific delay */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+ clock-frequency = <355000>;
+
+ tof_sensor: vl53l0x@29 {
+ compatible = "st,vl53l0x";
+ reg = <0x29>;
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&blsp2_i2c5 {
+ status = "okay";
+ clock-frequency = <355000>;
+
+ /* FUSB301 USB-C controller */
+};
+
+&blsp2_i2c6 {
+ status = "okay";
+ clock-frequency = <355000>;
+
+ synaptics@2c {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x2c>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&panel_tvdd>;
+
+ syna,reset-delay-ms = <220>;
+ syna,startup-delay-ms = <220>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f11@11 {
+ reg = <0x11>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&blsp2_uart2 {
+ status = "okay";
+};
+
+&camera0_mclk {
+ drive-strength = <2>;
+ output-low;
+};
+
+&camera0_pwdn {
+ drive-strength = <2>;
+ output-low;
+};
+
+&camera0_rst {
+ pins = "gpio30";
+ drive-strength = <2>;
+ output-low;
+};
+
+&camera2_mclk {
+ drive-strength = <2>;
+ output-low;
+};
+
+&camera2_rst {
+ drive-strength = <2>;
+ output-low;
+};
+
+&hsusb_phy1 {
+ status = "okay";
+
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
+};
+
+&mmcc {
+ vdd-gfx-supply = <&vdd_gfx>;
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+ vddpe-3v3-supply = <&wlan_en>;
+ vdda-supply = <&pm8994_l28>;
+};
+
+&pcie_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+};
+
+&pm8994_gpios {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8994_gpios_defaults>;
+ gpio-line-names =
+ "NC",
+ "VOL_DOWN_N",
+ "VOL_UP_N",
+ "SNAPSHOT_N",
+ "FOCUS_N",
+ "NC",
+ "NFC_VEN",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "EAR_EN",
+ "NC",
+ "PM_DIVCLK1",
+ "PMI_CLK",
+ "NC",
+ "WL_SLEEP_CLK",
+ "NC",
+ "PMIC_SPON",
+ "UIM_BATT_ALARM",
+ "PMK_SLEEP_CLK";
+
+ /*
+ * We don't yet know for sure which GPIOs are of our interest, but what
+ * we do know is that if a vendor sets the pins to a non-default state, there's
+ * probably a reason for it, and just to be on the safe side, we follow suit.
+ */
+ pm8994_gpios_defaults: pm8994-gpios-default-state {
+ pm8994-gpio1-nc {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ bias-high-impedance;
+ };
+
+ vol-down-n {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ vol-up-n {
+ pins = "gpio3";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ input-enable;
+ bias-pull-up;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ camera-snapshot-n {
+ pins = "gpio4";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ camera-focus-n {
+ pins = "gpio5";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ input-enable;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pm8994-gpio6-nc {
+ pins = "gpio6";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ bias-high-impedance;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ nfc-download {
+ pins = "gpio7";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ drive-push-pull;
+ bias-disable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pm8994-gpio8-nc {
+ pins = "gpio8";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ drive-push-pull;
+ bias-high-impedance;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ pm8994-gpio9-nc {
+ pins = "gpio9";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-high;
+ drive-push-pull;
+ bias-high-impedance;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ nfc-clock {
+ pins = "gpio10";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-enable;
+ drive-push-pull;
+ bias-pull-down;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pm8994-gpio11-nc {
+ pins = "gpio11";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ bias-high-impedance;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ pm8994-gpio12-nc {
+ pins = "gpio12";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ bias-high-impedance;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ ear-enable {
+ pins = "gpio13";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-high;
+ drive-push-pull;
+ bias-disable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pm8994-gpio14-nc {
+ pins = "gpio14";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ input-enable;
+ bias-high-impedance;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ pm-divclk1-gpio {
+ pins = "gpio15";
+ function = "func1";
+ output-high;
+ drive-push-pull;
+ bias-high-impedance;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ pmi-clk-gpio {
+ pins = "gpio16";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ };
+
+ pm8994-gpio17-nc {
+ pins = "gpio17";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ bias-high-impedance;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ rome-sleep {
+ pins = "gpio18";
+ function = PMIC_GPIO_FUNC_FUNC2;
+ output-low;
+ drive-push-pull;
+ bias-disable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pm8994-gpio19-nc {
+ pins = "gpio19";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ drive-push-pull;
+ bias-high-impedance;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ pm8994-gpio22-nc {
+ pins = "gpio22";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ bias-high-impedance;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+ };
+};
+
+&pm8994_mpps {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8994_mpps_defaults>;
+
+ gpio-line-names =
+ "SDC_UIM_VBIAS",
+ "LCD_ID_ADC",
+ "VREF_DACX",
+ "NC",
+ "FLASH_THERM",
+ "NC",
+ "NC",
+ "RF_ID";
+
+ pm8994_mpps_defaults: pm8994-mpps-default-state {
+ lcd-id_adc-mpp {
+ pins = "mpp2";
+ function = PMIC_MPP_FUNC_ANALOG;
+ input-enable;
+ qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH6>;
+ };
+
+ pm-mpp4-nc {
+ pins = "mpp4";
+ function = PMIC_MPP_FUNC_DIGITAL;
+ bias-high-impedance;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ flash-therm-mpp {
+ pins = "mpp5";
+ function = PMIC_MPP_FUNC_ANALOG;
+ input-enable;
+ qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+ };
+
+ mpp6-nc {
+ pins = "mpp6";
+ function = PMIC_MPP_FUNC_DIGITAL;
+ bias-high-impedance;
+ };
+
+ rf-id-mpp {
+ pins = "mpp8";
+ function = PMIC_MPP_FUNC_ANALOG;
+ input-enable;
+ qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH8>;
+ };
+ };
+};
+
+&pm8994_resin {
+ status = "okay";
+ linux,code = <KEY_VOLUMEUP>;
+};
+
+&pmi8994_gpios {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmi8994_gpios_defaults>;
+
+ gpio-line-names =
+ "VIB_LDO_EN",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "USB_SWITCH_SEL",
+ "NC";
+
+ pmi8994_gpios_defaults: pmi8994-gpios-default-state {
+ vib-ldo-en-gpio {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ output-low;
+ bias-disable;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pmi-gpio2-nc {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ input-enable;
+ bias-high-impedance;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ pmi-gpio3-nc {
+ pins = "gpio3";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ input-enable;
+ bias-high-impedance;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_VPH>;
+ };
+
+ pmi-gpio4-nc {
+ pins = "gpio4";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ output-high;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pmi-gpio5-nc {
+ pins = "gpio5";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ output-high;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pmi-gpio6-nc {
+ pins = "gpio6";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ output-high;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pmi-gpio7-nc {
+ pins = "gpio7";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ output-high;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ pmi-gpio8-nc {
+ pins = "gpio8";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ output-high;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ usb-switch-sel {
+ pins = "gpio9";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ drive-push-pull;
+ };
+
+ pmi-gpio10-nc {
+ pins = "gpio10";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ drive-push-pull;
+ bias-disable;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>;
+ };
+ };
+};
+
+&pmi8994_spmi_regulators {
+ qcom,saw-reg = <&saw3>;
+
+ vdd_gfx:
+ pmi8994_s2: s2 {
+ /* Pinned to a high value for now to avoid random crashes. */
+ regulator-min-microvolt = <1015000>;
+ regulator-max-microvolt = <1015000>;
+ regulator-name = "vdd_gfx";
+ regulator-always-on;
+ };
+
+ pmi8994_s9: s9 {
+ qcom,saw-slave;
+ };
+
+ pmi8994_s10: s10 {
+ qcom,saw-slave;
+ };
+
+ pmi8994_s11: s11 {
+ qcom,saw-leader;
+ regulator-always-on;
+ regulator-min-microvolt = <470000>;
+ regulator-max-microvolt = <1140000>;
+ };
+};
+
+&pmi8994_wled {
+ status = "okay";
+ default-brightness = <512>;
+};
+
+&rpm_requests {
+ pm8994-regulators {
+ compatible = "qcom,rpm-pm8994-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+ vdd_s7-supply = <&vph_pwr>;
+ vdd_s8-supply = <&vph_pwr>;
+ vdd_s9-supply = <&vph_pwr>;
+ vdd_s10-supply = <&vph_pwr>;
+ vdd_s11-supply = <&vph_pwr>;
+ vdd_s12-supply = <&vph_pwr>;
+ vdd_l1-supply = <&pm8994_s3>;
+ vdd_l2_l26_l28-supply = <&pm8994_s3>;
+ vdd_l3_l11-supply = <&pm8994_s3>;
+ vdd_l4_l27_l31-supply = <&pm8994_s3>;
+ vdd_l5_l7-supply = <&pm8994_s5>;
+ vdd_l6_l12_l32-supply = <&pm8994_s5>;
+ vdd_l8_l16_l30-supply = <&vph_pwr>;
+ vdd_l14_l15-supply = <&pm8994_s5>;
+ vdd_l20_l21-supply = <&pm8994_s5>;
+ vdd_l25-supply = <&pm8994_s3>;
+ vdd_lvs1_2-supply = <&pm8994_s4>;
+
+ pm8994_s3: s3 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8994_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-system-load = <325000>;
+ regulator-always-on;
+ };
+
+ pm8994_s5: s5 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };
+
+ pm8994_s7: s7 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ pm8994_l1: l1 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ pm8994_l2: l2 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ };
+
+ pm8994_l3: l3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ pm8994_l4: l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ /* L6 and L7 seem unused. */
+
+ pm8994_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8994_l9: l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8994_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8994_l11: l11 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ pm8994_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allow-set-load;
+ };
+
+ pm8994_l13: l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-system-load = <22000>;
+ regulator-allow-set-load;
+ };
+
+ pm8994_l14: l14 {
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ };
+
+ pm8994_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8994_l16: l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ pm8994_l17: l17 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ pm8994_l18: l18 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8994_l19: l19 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8994_l20: l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-system-load = <570000>;
+ regulator-allow-set-load;
+ };
+
+ pm8994_l21: l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-system-load = <800000>;
+ regulator-allow-set-load;
+ };
+
+ pm8994_l22: l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8994_l23: l23 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ pm8994_l24: l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ regulator-allow-set-load;
+ };
+
+ pm8994_l25: l25 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ };
+
+ pm8994_l27: l27 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8994_l28: l28 {
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <925000>;
+ regulator-allow-set-load;
+ };
+
+ pm8994_l29: l29 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ pm8994_l30: l30 { };
+
+ pm8994_l32: l32 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+};
+
+&sdhc1 {
+ /* eMMC doesn't seem to cooperate even in PIO mode.. */
+ status = "disabled";
+
+ vmmc-supply = <&pm8994_l20>;
+ vqmmc-supply = <&pm8994_s4>;
+ mmc-hs400-1_8v;
+ mmc-hs200-1_8v;
+};
+
+&sdhc2 {
+ status = "okay";
+
+ cd-gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&pm8994_l21>;
+ vqmmc-supply = <&pm8994_l13>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>;
+ pinctrl-0 = <&sw_service_gpio>;
+ pinctrl-names = "default";
+
+ disp_reset_n_gpio: disp-reset-n {
+ pins = "gpio8";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ mdp_vsync_p_gpio: mdp-vsync-p {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sw_service_gpio: sw-service-gpio {
+ pins = "gpio16";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ usb_detect: usb-detect {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
+ uim_detect_en: uim-detect-en {
+ pins = "gpio29";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
+ tray_det_pin: tray-det {
+ pins = "gpio40";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tp_vddio_en: tp-vddio-en {
+ pins = "gpio50";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
+ lcd_vddio_en: lcd-vddio-en {
+ pins = "gpio51";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ wl_host_wake: wl-host-wake {
+ pins = "gpio79";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ input-high;
+ };
+
+ wl_reg_on: wl-reg-on {
+ pins = "gpio84";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ ts_reset_n: ts-rst-n {
+ pins = "gpio89";
+ function = "gpio";
+ drive-strength = <2>;
+ };
+
+ touch_int_n: touch-int-n {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ touch_int_sleep: touch-int-sleep {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+};
+
+/*
+ * For reasons that are currently unknown (but probably related to fusb301), USB takes about
+ * 6 minutes to wake up (nothing interesting in kernel logs), but then it works as it should.
+ */
+&usb3 {
+ status = "okay";
+ qcom,select-utmi-as-pipe-clk;
+};
+
+&usb3_dwc3 {
+ extcon = <&usb3_id>;
+ dr_mode = "peripheral";
+ phys = <&hsusb_phy1>;
+ phy-names = "usb2-phy";
+ snps,hird-threshold = /bits/ 8 <0>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index b5ec2a756561..54f5ba2c8878 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -852,21 +852,21 @@ cci0_default: cci0-default {
camera0_state_on:
camera_rear_default: camera-rear-default {
- mclk0 {
+ camera0_mclk: mclk0 {
pins = "gpio13";
function = "cam_mclk";
drive-strength = <16>;
bias-disable;
};
- rst {
+ camera0_rst: rst {
pins = "gpio25";
function = "gpio";
drive-strength = <16>;
bias-disable;
};
- pwdn {
+ camera0_pwdn: pwdn {
pins = "gpio26";
function = "gpio";
drive-strength = <16>;
@@ -907,14 +907,14 @@ rst {
camera2_state_on:
camera_front_default: camera-front-default {
- mclk2 {
+ camera2_mclk: mclk2 {
pins = "gpio15";
function = "cam_mclk";
drive-strength = <16>;
bias-disable;
};
- rst {
+ camera2_rst: rst {
pins = "gpio23";
function = "gpio";
drive-strength = <16>;
@@ -2331,7 +2331,7 @@ usb3: usb@6af8800 {
power-domains = <&gcc USB30_GDSC>;
status = "disabled";
- dwc3@6a00000 {
+ usb3_dwc3: dwc3@6a00000 {
compatible = "snps,dwc3";
reg = <0x06a00000 0xcc00>;
interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>;
--
2.31.1
prev parent reply other threads:[~2021-06-08 20:21 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-08 20:21 [PATCH v4 1/4] arm64: dts: qcom: Add PMI8996 DTSI file Konrad Dybcio
2021-06-08 20:21 ` [PATCH v4 2/4] arm64: dts: qcom: Add MSM8996v3.0 " Konrad Dybcio
2021-06-08 20:21 ` [PATCH v4 3/4] arm64: dts: qcom: msm8996-*: Disable HDMI by default Konrad Dybcio
2021-06-08 20:21 ` Konrad Dybcio [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210608202143.247427-4-konrad.dybcio@somainline.org \
--to=konrad.dybcio@somainline.org \
--cc=agross@kernel.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=anton@enomsg.org \
--cc=bjorn.andersson@linaro.org \
--cc=ccross@android.com \
--cc=devicetree@vger.kernel.org \
--cc=jamipkettunen@somainline.org \
--cc=keescook@chromium.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marijn.suijten@somainline.org \
--cc=martin.botka@somainline.org \
--cc=robh+dt@kernel.org \
--cc=tony.luck@intel.com \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.