All of lore.kernel.org
 help / color / mirror / Atom feed
From: Breno Lima <breno.lima@nxp.com>
To: peter.chen@kernel.org
Cc: gregkh@linuxfoundation.org, shawnguo@kernel.org,
	s.hauer@pengutronix.de, kernel@pengutronix.de,
	festevam@gmail.com, linux-imx@nxp.com, linux-usb@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, brenomatheus@gmail.com,
	jun.li@nxp.com, Breno Lima <breno.lima@nxp.com>
Subject: [PATCH] mx8mm: usb: chipidea: Fix Battery Charger 1.2 CDP detection
Date: Thu, 10 Jun 2021 21:47:55 -0400	[thread overview]
Message-ID: <20210611014755.124483-1-breno.lima@nxp.com> (raw)

i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.

During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the PD is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.

During secondary detection the PD is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).

Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.

VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
---
 drivers/usb/chipidea/usbmisc_imx.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c
index 4545b23bda3f..bac0f5458cab 100644
--- a/drivers/usb/chipidea/usbmisc_imx.c
+++ b/drivers/usb/chipidea/usbmisc_imx.c
@@ -686,6 +686,16 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 	int val;
 	unsigned long flags;
 
+	/* Clear VDATSRCENB0 to disable VDP_SRC and IDM_SNK required by BC 1.2 spec */
+	spin_lock_irqsave(&usbmisc->lock, flags);
+	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	val &= ~MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0;
+	writel(val, usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+	/* TVDMSRC_DIS */
+	msleep(20);
+
 	/* VDM_SRC is connected to D- and IDP_SINK is connected to D+ */
 	spin_lock_irqsave(&usbmisc->lock, flags);
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
@@ -695,7 +705,8 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDMSRC_ON */
+	msleep(40);
 
 	/*
 	 * Per BC 1.2, check voltage of D+:
@@ -798,7 +809,8 @@ static int imx7d_charger_primary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDPSRC_ON */
+	msleep(40);
 
 	/* Check if D- is less than VDAT_REF to determine an SDP per BC 1.2 */
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
-- 
2.25.1


WARNING: multiple messages have this Message-ID (diff)
From: Breno Lima <breno.lima@nxp.com>
To: peter.chen@kernel.org
Cc: gregkh@linuxfoundation.org, shawnguo@kernel.org,
	s.hauer@pengutronix.de, kernel@pengutronix.de,
	festevam@gmail.com, linux-imx@nxp.com, linux-usb@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, brenomatheus@gmail.com,
	jun.li@nxp.com, Breno Lima <breno.lima@nxp.com>
Subject: [PATCH] mx8mm: usb: chipidea: Fix Battery Charger 1.2 CDP detection
Date: Thu, 10 Jun 2021 21:47:55 -0400	[thread overview]
Message-ID: <20210611014755.124483-1-breno.lima@nxp.com> (raw)

i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.

During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the PD is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.

During secondary detection the PD is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).

Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.

VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
---
 drivers/usb/chipidea/usbmisc_imx.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c
index 4545b23bda3f..bac0f5458cab 100644
--- a/drivers/usb/chipidea/usbmisc_imx.c
+++ b/drivers/usb/chipidea/usbmisc_imx.c
@@ -686,6 +686,16 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 	int val;
 	unsigned long flags;
 
+	/* Clear VDATSRCENB0 to disable VDP_SRC and IDM_SNK required by BC 1.2 spec */
+	spin_lock_irqsave(&usbmisc->lock, flags);
+	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	val &= ~MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0;
+	writel(val, usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
+	spin_unlock_irqrestore(&usbmisc->lock, flags);
+
+	/* TVDMSRC_DIS */
+	msleep(20);
+
 	/* VDM_SRC is connected to D- and IDP_SINK is connected to D+ */
 	spin_lock_irqsave(&usbmisc->lock, flags);
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
@@ -695,7 +705,8 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDMSRC_ON */
+	msleep(40);
 
 	/*
 	 * Per BC 1.2, check voltage of D+:
@@ -798,7 +809,8 @@ static int imx7d_charger_primary_detection(struct imx_usbmisc_data *data)
 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
 	spin_unlock_irqrestore(&usbmisc->lock, flags);
 
-	usleep_range(1000, 2000);
+	/* TVDPSRC_ON */
+	msleep(40);
 
 	/* Check if D- is less than VDAT_REF to determine an SDP per BC 1.2 */
 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2021-06-11  1:48 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-11  1:47 Breno Lima [this message]
2021-06-11  1:47 ` [PATCH] mx8mm: usb: chipidea: Fix Battery Charger 1.2 CDP detection Breno Lima
2021-06-11  6:24 ` Jun Li
2021-06-11  6:24   ` Jun Li
2021-06-11 14:57   ` Breno Matheus Lima
2021-06-11 14:57     ` Breno Matheus Lima

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210611014755.124483-1-breno.lima@nxp.com \
    --to=breno.lima@nxp.com \
    --cc=brenomatheus@gmail.com \
    --cc=festevam@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=jun.li@nxp.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=peter.chen@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.