From: Takashi Sakamoto <o-takashi@sakamocchi.jp>
To: tiwai@suse.de
Cc: alsa-devel@alsa-project.org, clemens@ladisch.de
Subject: [PATCH 2/2] ALSA: firewire-motu: add support for MOTU 896
Date: Wed, 16 Jun 2021 17:28:47 +0900 [thread overview]
Message-ID: <20210616082847.124688-3-o-takashi@sakamocchi.jp> (raw)
In-Reply-To: <20210616082847.124688-1-o-takashi@sakamocchi.jp>
MOTU 896 is a second model in MOTU FireWire series, produced in 2001. This
model consists of three chips:
* Texas Instruments TSB41AB2 (Physical layer for IEEE 1394 bus)
* Philips Semiconductors PDI 1394L21BE (Link layer for IEEE 1394 bus and
packet processing layer)
* QuickLogic QuickRAM QL4016 (Data block processing layer and digital
signal processing)
This commit adds a support for the model, with its unique protocol as
version 1. The features of this protocol are:
* no MIDI support.
* Rx packets have no data chunks for control and status messages.
* Tx packets have 2 bytes for control and status messages in the end of
each data block.
* The most of settings are represented in bit flag in one quadlet address
(0x'ffff'f000'0b14).
* It's selectable to use signal on optical interface, however the device
has no register specific to it. The state has effect just to whether
to exclude differed data chunks.
* The internal multiplexer is not configured by software.
Just after powering on, the device has a quirk to fail handling
transaction. I recommend users to connect the device enough after powering
on.
$ python3 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04102814 bus_info_length 4, crc_length 16, crc 10260
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 0000d645 device_id 000000d645 | EUI-64 0001f2000000d645
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 0003ab34 directory_length 3, crc 43828
42c 120001f2 specifier id
430 13000002 version
434 17102801 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002057d leaf_length 2, crc 1405
43c 0001f200 company_id 0001f2 |
440 0000d645 device_id 000000d645 | EUI-64 0001f2000000d645
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
---
sound/firewire/Kconfig | 1 +
sound/firewire/motu/motu-protocol-v1.c | 215 +++++++++++++++++++++++++
sound/firewire/motu/motu.c | 1 +
sound/firewire/motu/motu.h | 1 +
4 files changed, 218 insertions(+)
diff --git a/sound/firewire/Kconfig b/sound/firewire/Kconfig
index a70732bbddab..62658e2b111a 100644
--- a/sound/firewire/Kconfig
+++ b/sound/firewire/Kconfig
@@ -166,6 +166,7 @@ config SND_FIREWIRE_MOTU
help
Say Y here to enable support for FireWire devices which MOTU produced:
* 828
+ * 896
* 828mk2
* Traveler
* Ultralite
diff --git a/sound/firewire/motu/motu-protocol-v1.c b/sound/firewire/motu/motu-protocol-v1.c
index fab6aef392af..d3eb9f377b71 100644
--- a/sound/firewire/motu/motu-protocol-v1.c
+++ b/sound/firewire/motu/motu-protocol-v1.c
@@ -53,6 +53,62 @@
#define CLK_828_STATUS_FLAG_SRC_SPDIF_ON_OPT_OR_COAX 0x00000002
#define CLK_828_STATUS_FLAG_SRC_ADAT_ON_OPT_OR_DSUB 0x00000001
+// Status register for MOTU 896 (0x'ffff'f000'0b14).
+//
+// 0x20000000: fetch PCM frames from communication IC to DAC.
+// 0x08000000: speed of word clock signal output on BNC interface.
+// 0x00000000: follow to system clock.
+// 0x08000000: half of system clock.
+// 0x01000000: Route main output to headphone output.
+// 0x00ffff00: input to monitor.
+// 0x00000000: none
+// 0x00004800: analog-1/2
+// 0x00005a00: analog-3/4
+// 0x00006c00: analog-5/6
+// 0x00007e00: analog-7/8
+// 0x00104800: AES/EBU-1/2
+// 0x00004000: analog-1
+// 0x00004900: analog-2
+// 0x00005200: analog-3
+// 0x00005b00: analog-4
+// 0x00006400: analog-5
+// 0x00006d00: analog-6
+// 0x00007600: analog-7
+// 0x00007f00: analog-8
+// 0x00104000: AES/EBU-1
+// 0x00104900: AES/EBU-2
+// 0x00000060: sample rate conversin for AES/EBU input/output.
+// 0x00000000: None
+// 0x00000020: input signal is converted to system rate
+// 0x00000040: output is slave to input, ignoring system rate
+// 0x00000060: output is double rate than system rate
+// 0x00000018: nominal rate of sampling clock.
+// 0x00000000: 44.1 kHz
+// 0x00000008: 48.0 kHz
+// 0x00000010: 88.2 kHz
+// 0x00000018: 96.0 kHz
+// 0x00000007: source of sampling clock.
+// 0x00000000: internal
+// 0x00000001: ADAT on optical interface
+// 0x00000002: AES/EBU on XLR
+// 0x00000004: word clock on BNC
+// 0x00000005: ADAT on Dsub 9pin
+
+#define CLK_896_STATUS_OFFSET 0x0b14
+#define CLK_896_STATUS_FLAG_FETCH_ENABLE 0x20000000
+#define CLK_896_STATUS_FLAG_MAIN_TO_HP 0x01000000
+#define CLK_896_STATUS_MASK_SRC 0x00000007
+#define CLK_896_STATUS_FLAG_SRC_INTERNAL 0x00000000
+#define CLK_896_STATUS_FLAG_SRC_ADAT_ON_OPT 0x00000001
+#define CLK_896_STATUS_FLAG_SRC_AESEBU 0x00000002
+#define CLK_896_STATUS_FLAG_SRC_WORD 0x00000004
+#define CLK_896_STATUS_FLAG_SRC_ADAT_ON_DSUB 0x00000005
+#define CLK_896_STATUS_MASK_RATE 0x00000018
+#define CLK_896_STATUS_FLAG_RATE_44100 0x00000000
+#define CLK_896_STATUS_FLAG_RATE_48000 0x00000008
+#define CLK_896_STATUS_FLAG_RATE_88200 0x00000010
+#define CLK_896_STATUS_FLAG_RATE_96000 0x00000018
+
static void parse_clock_rate_828(u32 data, unsigned int *rate)
{
if (data & CLK_828_STATUS_FLAG_RATE_48000)
@@ -74,10 +130,45 @@ static int get_clock_rate_828(struct snd_motu *motu, unsigned int *rate)
return 0;
}
+static int parse_clock_rate_896(u32 data, unsigned int *rate)
+{
+ switch (data & CLK_896_STATUS_MASK_RATE) {
+ case CLK_896_STATUS_FLAG_RATE_44100:
+ *rate = 44100;
+ break;
+ case CLK_896_STATUS_FLAG_RATE_48000:
+ *rate = 48000;
+ break;
+ case CLK_896_STATUS_FLAG_RATE_88200:
+ *rate = 88200;
+ break;
+ case CLK_896_STATUS_FLAG_RATE_96000:
+ *rate = 96000;
+ break;
+ default:
+ return -ENXIO;
+ }
+
+ return 0;
+}
+
+static int get_clock_rate_896(struct snd_motu *motu, unsigned int *rate)
+{
+ __be32 reg;
+ int err;
+
+ err = snd_motu_transaction_read(motu, CLK_896_STATUS_OFFSET, ®, sizeof(reg));
+ if (err < 0)
+ return err;
+ return parse_clock_rate_896(be32_to_cpu(reg), rate);
+}
+
int snd_motu_protocol_v1_get_clock_rate(struct snd_motu *motu, unsigned int *rate)
{
if (motu->spec == &snd_motu_spec_828)
return get_clock_rate_828(motu, rate);
+ else if (motu->spec == &snd_motu_spec_896)
+ return get_clock_rate_896(motu, rate);
else
return -ENXIO;
}
@@ -101,10 +192,48 @@ static int set_clock_rate_828(struct snd_motu *motu, unsigned int rate)
return snd_motu_transaction_write(motu, CLK_828_STATUS_OFFSET, ®, sizeof(reg));
}
+static int set_clock_rate_896(struct snd_motu *motu, unsigned int rate)
+{
+ unsigned int flag;
+ __be32 reg;
+ u32 data;
+ int err;
+
+ err = snd_motu_transaction_read(motu, CLK_896_STATUS_OFFSET, ®, sizeof(reg));
+ if (err < 0)
+ return err;
+ data = be32_to_cpu(reg);
+
+ switch (rate) {
+ case 44100:
+ flag = CLK_896_STATUS_FLAG_RATE_44100;
+ break;
+ case 48000:
+ flag = CLK_896_STATUS_FLAG_RATE_48000;
+ break;
+ case 88200:
+ flag = CLK_896_STATUS_FLAG_RATE_88200;
+ break;
+ case 96000:
+ flag = CLK_896_STATUS_FLAG_RATE_96000;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ data &= ~CLK_896_STATUS_MASK_RATE;
+ data |= flag;
+
+ reg = cpu_to_be32(data);
+ return snd_motu_transaction_write(motu, CLK_896_STATUS_OFFSET, ®, sizeof(reg));
+}
+
int snd_motu_protocol_v1_set_clock_rate(struct snd_motu *motu, unsigned int rate)
{
if (motu->spec == &snd_motu_spec_828)
return set_clock_rate_828(motu, rate);
+ else if (motu->spec == &snd_motu_spec_896)
+ return set_clock_rate_896(motu, rate);
else
return -ENXIO;
}
@@ -137,10 +266,46 @@ static int get_clock_source_828(struct snd_motu *motu, enum snd_motu_clock_sourc
return 0;
}
+static int get_clock_source_896(struct snd_motu *motu, enum snd_motu_clock_source *src)
+{
+ __be32 reg;
+ u32 data;
+ int err;
+
+ err = snd_motu_transaction_read(motu, CLK_896_STATUS_OFFSET, ®, sizeof(reg));
+ if (err < 0)
+ return err;
+ data = be32_to_cpu(reg);
+
+ switch (data & CLK_896_STATUS_MASK_SRC) {
+ case CLK_896_STATUS_FLAG_SRC_INTERNAL:
+ *src = SND_MOTU_CLOCK_SOURCE_INTERNAL;
+ break;
+ case CLK_896_STATUS_FLAG_SRC_ADAT_ON_OPT:
+ *src = SND_MOTU_CLOCK_SOURCE_ADAT_ON_OPT;
+ break;
+ case CLK_896_STATUS_FLAG_SRC_AESEBU:
+ *src = SND_MOTU_CLOCK_SOURCE_AESEBU_ON_XLR;
+ break;
+ case CLK_896_STATUS_FLAG_SRC_WORD:
+ *src = SND_MOTU_CLOCK_SOURCE_WORD_ON_BNC;
+ break;
+ case CLK_896_STATUS_FLAG_SRC_ADAT_ON_DSUB:
+ *src = SND_MOTU_CLOCK_SOURCE_ADAT_ON_DSUB;
+ break;
+ default:
+ return -ENXIO;
+ }
+
+ return 0;
+}
+
int snd_motu_protocol_v1_get_clock_source(struct snd_motu *motu, enum snd_motu_clock_source *src)
{
if (motu->spec == &snd_motu_spec_828)
return get_clock_source_828(motu, src);
+ else if (motu->spec == &snd_motu_spec_896)
+ return get_clock_source_896(motu, src);
else
return -ENXIO;
}
@@ -169,10 +334,31 @@ static int switch_fetching_mode_828(struct snd_motu *motu, bool enable)
return snd_motu_transaction_write(motu, CLK_828_STATUS_OFFSET, ®, sizeof(reg));
}
+static int switch_fetching_mode_896(struct snd_motu *motu, bool enable)
+{
+ __be32 reg;
+ u32 data;
+ int err;
+
+ err = snd_motu_transaction_read(motu, CLK_896_STATUS_OFFSET, ®, sizeof(reg));
+ if (err < 0)
+ return err;
+ data = be32_to_cpu(reg);
+
+ data &= ~(CLK_896_STATUS_FLAG_FETCH_ENABLE | CLK_896_STATUS_FLAG_MAIN_TO_HP);
+ if (enable)
+ data |= (CLK_896_STATUS_FLAG_FETCH_ENABLE | CLK_896_STATUS_FLAG_MAIN_TO_HP);
+
+ reg = cpu_to_be32(data);
+ return snd_motu_transaction_write(motu, CLK_896_STATUS_OFFSET, ®, sizeof(reg));
+}
+
int snd_motu_protocol_v1_switch_fetching_mode(struct snd_motu *motu, bool enable)
{
if (motu->spec == &snd_motu_spec_828)
return switch_fetching_mode_828(motu, enable);
+ else if (motu->spec == &snd_motu_spec_896)
+ return switch_fetching_mode_896(motu, enable);
else
return -ENXIO;
}
@@ -204,6 +390,27 @@ static int detect_packet_formats_828(struct snd_motu *motu)
return 0;
}
+static int detect_packet_formats_896(struct snd_motu *motu)
+{
+ // 24bit PCM frames follow to source packet header without message chunk.
+ motu->tx_packet_formats.pcm_byte_offset = 4;
+ motu->rx_packet_formats.pcm_byte_offset = 4;
+
+ // No message chunk in data block.
+ motu->tx_packet_formats.msg_chunks = 0;
+ motu->rx_packet_formats.msg_chunks = 0;
+
+ // Always enable optical interface for ADAT signal since the device have no registers
+ // to refer to current configuration.
+ motu->tx_packet_formats.pcm_chunks[0] += 8;
+ motu->tx_packet_formats.pcm_chunks[1] += 8;
+
+ motu->rx_packet_formats.pcm_chunks[0] += 8;
+ motu->rx_packet_formats.pcm_chunks[1] += 8;
+
+ return 0;
+}
+
int snd_motu_protocol_v1_cache_packet_formats(struct snd_motu *motu)
{
memcpy(motu->tx_packet_formats.pcm_chunks, motu->spec->tx_fixed_pcm_chunks,
@@ -213,6 +420,8 @@ int snd_motu_protocol_v1_cache_packet_formats(struct snd_motu *motu)
if (motu->spec == &snd_motu_spec_828)
return detect_packet_formats_828(motu);
+ else if (motu->spec == &snd_motu_spec_896)
+ return detect_packet_formats_896(motu);
else
return 0;
}
@@ -223,3 +432,9 @@ const struct snd_motu_spec snd_motu_spec_828 = {
.tx_fixed_pcm_chunks = {10, 0, 0},
.rx_fixed_pcm_chunks = {10, 0, 0},
};
+
+const struct snd_motu_spec snd_motu_spec_896 = {
+ .name = "896",
+ .tx_fixed_pcm_chunks = {10, 10, 0},
+ .rx_fixed_pcm_chunks = {10, 10, 0},
+};
diff --git a/sound/firewire/motu/motu.c b/sound/firewire/motu/motu.c
index add5f183dc1d..0cae670d711c 100644
--- a/sound/firewire/motu/motu.c
+++ b/sound/firewire/motu/motu.c
@@ -151,6 +151,7 @@ static void motu_bus_update(struct fw_unit *unit)
static const struct ieee1394_device_id motu_id_table[] = {
SND_MOTU_DEV_ENTRY(0x000001, &snd_motu_spec_828),
+ SND_MOTU_DEV_ENTRY(0x000002, &snd_motu_spec_896),
SND_MOTU_DEV_ENTRY(0x000003, &snd_motu_spec_828mk2),
SND_MOTU_DEV_ENTRY(0x000009, &snd_motu_spec_traveler),
SND_MOTU_DEV_ENTRY(0x00000d, &snd_motu_spec_ultralite),
diff --git a/sound/firewire/motu/motu.h b/sound/firewire/motu/motu.h
index 13e2637a0330..a3deabdf9e34 100644
--- a/sound/firewire/motu/motu.h
+++ b/sound/firewire/motu/motu.h
@@ -123,6 +123,7 @@ struct snd_motu_spec {
};
extern const struct snd_motu_spec snd_motu_spec_828;
+extern const struct snd_motu_spec snd_motu_spec_896;
extern const struct snd_motu_spec snd_motu_spec_828mk2;
extern const struct snd_motu_spec snd_motu_spec_traveler;
--
2.30.2
next prev parent reply other threads:[~2021-06-16 8:30 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-16 8:28 [PATCH 0/2] ALSA: firewire-motu: add support for MOTU 828 and 896 Takashi Sakamoto
2021-06-16 8:28 ` [PATCH 1/2] ALSA: firewire-motu: add support for MOTU 828 Takashi Sakamoto
2021-06-16 8:28 ` Takashi Sakamoto [this message]
2021-06-17 9:37 ` [PATCH 0/2] ALSA: firewire-motu: add support for MOTU 828 and 896 Takashi Iwai
2021-06-17 10:03 ` Takashi Sakamoto
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210616082847.124688-3-o-takashi@sakamocchi.jp \
--to=o-takashi@sakamocchi.jp \
--cc=alsa-devel@alsa-project.org \
--cc=clemens@ladisch.de \
--cc=tiwai@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.