From: Vyacheslav Bocharov <adeep@lexina.in>
To: Neil Armstrong <narmstrong@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 2/3] arm64: dts: meson-axg: add support for JetHub D1
Date: Thu, 2 Sep 2021 16:05:15 +0300 [thread overview]
Message-ID: <20210902130516.3892452-3-adeep@lexina.in> (raw)
In-Reply-To: <20210902130516.3892452-1-adeep@lexina.in>
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../amlogic/meson-axg-jethome-jethub-j100.dts | 439 ++++++++++++++++++
2 files changed, 440 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..68d688528c86
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,439 @@
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "jethome,j100", "amlogic,a113d", "amlogic,meson-axg";
+ model = "JetHome JetHub J100";
+ amlogic-dt-id = "axg_jethubj100_v1";
+
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_B; /* Bluetooth */
+ serial2 = &uart_AO_B; /* External UART (Wireless Module) */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /* 1024MB RAM */
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable; size = <0x0 0x400000>;
+ alignment = <0x0 0x400000>;
+ linux,cma-default;
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ usb_pwr: regulator-usb_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+ };
+
+ partitions: partitions {
+ parts = <1>;
+ part-0 = <&rootfs>;
+ rootfs: rootfs {
+ pname = "rootfs";
+ size = <0xffffffff 0xffffffff>;
+ mask = <4>;
+ };
+ };
+
+ efusekey: efusekey {
+ keynum = <5>;
+ key0 = <&key_0>;
+ key1 = <&key_1>;
+ key2 = <&key_2>;
+ key3 = <&key_3>;
+ key4 = <&key_4>;
+
+ key_0: key_0 {
+ keyname = "mac";
+ offset = <0>;
+ size = <6>;
+ };
+ key_1: key_1 {
+ keyname = "mac_bt";
+ offset = <6>;
+ size = <6>;
+ };
+ key_2: key_2 {
+ keyname = "mac_wifi";
+ offset = <12>;
+ size = <6>;
+ };
+ key_3: key_3 {
+ keyname = "usid";
+ offset = <18>;
+ size = <32>;
+ };
+ key_4: key_4 {
+ keyname = "serial";
+ offset = <50>;
+ size = <32>;
+ };
+ }; //End efusekey
+
+ unifykey {
+ compatible = "amlogic, unifykey";
+ status = "ok";
+ unifykey-num = <6>;
+ unifykey-index-0 = <&keysn_0>;
+ unifykey-index-1 = <&keysn_1>;
+ unifykey-index-2 = <&keysn_2>;
+ unifykey-index-3 = <&keysn_3>;
+ unifykey-index-4 = <&keysn_4>;
+ unifykey-index-5 = <&keysn_5>;
+
+ keysn_0: key_0 {
+ key-name = "usid";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_1: key_1 {
+ key-name = "mac";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_2: key_2 {
+ key-name = "mac_bt";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ key-type = "mac";
+ };
+ keysn_3: key_3 {
+ key-name = "mac_wifi";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ key-type = "mac";
+ };
+ keysn_4: key_4 {
+ key-name = "serial";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_5:key_5 {
+ key-name = "deviceid";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ };
+ }; //End unifykey
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&scpi_sensors 0>;
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_hot: cpu-hot {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+ cpu_critical: cpu-critical {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+ cpu_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rmii_x_pins>;
+ pinctrl-names = "default";
+ phy-handle = <ð_phy0>;
+ phy-mode = "rmii";
+ internal_phy=<0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+ eth_phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0243.0c54";
+ max-speed = <100>;
+ reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+ status = "okay";
+ pinctrl-0 = <&i2c1_z_pins>;
+ pinctrl-names = "default";
+
+ /* RTC */
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ status = "okay";
+ pinctrl-0 = <&pwm_a_x20_pins>;
+ pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* emmc storage */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+ status = "okay";
+ pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* UART Console */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+ status = "okay";
+};
+
+&audio {
+ status = "disabled";
+};
+
+&efuse {
+ status = "okay";
+ compatible = "amlogic,meson-gxbb-efuse", "amlogic, efuse";
+ read_cmd = <0x82000030>;
+ write_cmd = <0x82000031>;
+ get_max_cmd = <0x82000033>;
+ key = <&efusekey>;
+ clock-names = "efuse_clk";
+};
+
+&gpio {
+ interrupt-parent = <&gpio_intc>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-line-names =
+ "", "", "", "", "", // 0 - 4
+ "", "", "", "", "", // 5 - 9
+ "UserButton", "", "", "", "", // 10 - 14
+ "", "", "", "", "", // 15 - 19
+ "", "", "", "", "", // 20 - 24
+ "", "LEDRED", "LEDGREEN", "Output3", "Output2", // 25 - 29
+ "Output1", "", "", "", "", // 30 - 34
+ "", "ZigBeeBOOT", "", "", "", // 35 - 39
+ "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+ "Input2", "Input1", "", "", "", // 45 - 49
+ "", "", "", "", "", // 50 - 54
+ "", "", "", "", "", // 55 - 59
+ "", "", "", "", "", // 60 - 64
+ "", "", "", "", "", // 65 - 69
+ "", "", "", "", "", // 70 - 74
+ "", "", "", "", "", // 75 - 79
+ "", "", "", "", "", // 80 - 84
+ "", ""; // 85-86
+};
+
+&cpu0 {
+ #cooling-cells = <2>;
+};
+
+&cpu1 {
+ #cooling-cells = <2>;
+};
+
+&cpu2 {
+ #cooling-cells = <2>;
+};
+
+&cpu3 {
+ #cooling-cells = <2>;
+};
+
--
2.30.2
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
WARNING: multiple messages have this Message-ID (diff)
From: Vyacheslav Bocharov <adeep@lexina.in>
To: Neil Armstrong <narmstrong@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 2/3] arm64: dts: meson-axg: add support for JetHub D1
Date: Thu, 2 Sep 2021 16:05:15 +0300 [thread overview]
Message-ID: <20210902130516.3892452-3-adeep@lexina.in> (raw)
In-Reply-To: <20210902130516.3892452-1-adeep@lexina.in>
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../amlogic/meson-axg-jethome-jethub-j100.dts | 439 ++++++++++++++++++
2 files changed, 440 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..68d688528c86
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,439 @@
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "jethome,j100", "amlogic,a113d", "amlogic,meson-axg";
+ model = "JetHome JetHub J100";
+ amlogic-dt-id = "axg_jethubj100_v1";
+
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_B; /* Bluetooth */
+ serial2 = &uart_AO_B; /* External UART (Wireless Module) */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /* 1024MB RAM */
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable; size = <0x0 0x400000>;
+ alignment = <0x0 0x400000>;
+ linux,cma-default;
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ usb_pwr: regulator-usb_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+ };
+
+ partitions: partitions {
+ parts = <1>;
+ part-0 = <&rootfs>;
+ rootfs: rootfs {
+ pname = "rootfs";
+ size = <0xffffffff 0xffffffff>;
+ mask = <4>;
+ };
+ };
+
+ efusekey: efusekey {
+ keynum = <5>;
+ key0 = <&key_0>;
+ key1 = <&key_1>;
+ key2 = <&key_2>;
+ key3 = <&key_3>;
+ key4 = <&key_4>;
+
+ key_0: key_0 {
+ keyname = "mac";
+ offset = <0>;
+ size = <6>;
+ };
+ key_1: key_1 {
+ keyname = "mac_bt";
+ offset = <6>;
+ size = <6>;
+ };
+ key_2: key_2 {
+ keyname = "mac_wifi";
+ offset = <12>;
+ size = <6>;
+ };
+ key_3: key_3 {
+ keyname = "usid";
+ offset = <18>;
+ size = <32>;
+ };
+ key_4: key_4 {
+ keyname = "serial";
+ offset = <50>;
+ size = <32>;
+ };
+ }; //End efusekey
+
+ unifykey {
+ compatible = "amlogic, unifykey";
+ status = "ok";
+ unifykey-num = <6>;
+ unifykey-index-0 = <&keysn_0>;
+ unifykey-index-1 = <&keysn_1>;
+ unifykey-index-2 = <&keysn_2>;
+ unifykey-index-3 = <&keysn_3>;
+ unifykey-index-4 = <&keysn_4>;
+ unifykey-index-5 = <&keysn_5>;
+
+ keysn_0: key_0 {
+ key-name = "usid";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_1: key_1 {
+ key-name = "mac";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_2: key_2 {
+ key-name = "mac_bt";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ key-type = "mac";
+ };
+ keysn_3: key_3 {
+ key-name = "mac_wifi";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ key-type = "mac";
+ };
+ keysn_4: key_4 {
+ key-name = "serial";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_5:key_5 {
+ key-name = "deviceid";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ };
+ }; //End unifykey
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&scpi_sensors 0>;
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_hot: cpu-hot {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+ cpu_critical: cpu-critical {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+ cpu_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rmii_x_pins>;
+ pinctrl-names = "default";
+ phy-handle = <ð_phy0>;
+ phy-mode = "rmii";
+ internal_phy=<0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+ eth_phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0243.0c54";
+ max-speed = <100>;
+ reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+ status = "okay";
+ pinctrl-0 = <&i2c1_z_pins>;
+ pinctrl-names = "default";
+
+ /* RTC */
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ status = "okay";
+ pinctrl-0 = <&pwm_a_x20_pins>;
+ pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* emmc storage */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+ status = "okay";
+ pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* UART Console */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+ status = "okay";
+};
+
+&audio {
+ status = "disabled";
+};
+
+&efuse {
+ status = "okay";
+ compatible = "amlogic,meson-gxbb-efuse", "amlogic, efuse";
+ read_cmd = <0x82000030>;
+ write_cmd = <0x82000031>;
+ get_max_cmd = <0x82000033>;
+ key = <&efusekey>;
+ clock-names = "efuse_clk";
+};
+
+&gpio {
+ interrupt-parent = <&gpio_intc>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-line-names =
+ "", "", "", "", "", // 0 - 4
+ "", "", "", "", "", // 5 - 9
+ "UserButton", "", "", "", "", // 10 - 14
+ "", "", "", "", "", // 15 - 19
+ "", "", "", "", "", // 20 - 24
+ "", "LEDRED", "LEDGREEN", "Output3", "Output2", // 25 - 29
+ "Output1", "", "", "", "", // 30 - 34
+ "", "ZigBeeBOOT", "", "", "", // 35 - 39
+ "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+ "Input2", "Input1", "", "", "", // 45 - 49
+ "", "", "", "", "", // 50 - 54
+ "", "", "", "", "", // 55 - 59
+ "", "", "", "", "", // 60 - 64
+ "", "", "", "", "", // 65 - 69
+ "", "", "", "", "", // 70 - 74
+ "", "", "", "", "", // 75 - 79
+ "", "", "", "", "", // 80 - 84
+ "", ""; // 85-86
+};
+
+&cpu0 {
+ #cooling-cells = <2>;
+};
+
+&cpu1 {
+ #cooling-cells = <2>;
+};
+
+&cpu2 {
+ #cooling-cells = <2>;
+};
+
+&cpu3 {
+ #cooling-cells = <2>;
+};
+
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Vyacheslav Bocharov <adeep@lexina.in>
To: Neil Armstrong <narmstrong@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 2/3] arm64: dts: meson-axg: add support for JetHub D1
Date: Thu, 2 Sep 2021 16:05:15 +0300 [thread overview]
Message-ID: <20210902130516.3892452-3-adeep@lexina.in> (raw)
In-Reply-To: <20210902130516.3892452-1-adeep@lexina.in>
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../amlogic/meson-axg-jethome-jethub-j100.dts | 439 ++++++++++++++++++
2 files changed, 440 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..68d688528c86
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,439 @@
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "jethome,j100", "amlogic,a113d", "amlogic,meson-axg";
+ model = "JetHome JetHub J100";
+ amlogic-dt-id = "axg_jethubj100_v1";
+
+ aliases {
+ serial0 = &uart_AO; /* Console */
+ serial1 = &uart_B; /* Bluetooth */
+ serial2 = &uart_AO_B; /* External UART (Wireless Module) */
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ /* 1024MB RAM */
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable; size = <0x0 0x400000>;
+ alignment = <0x0 0x400000>;
+ linux,cma-default;
+ };
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ usb_pwr: regulator-usb_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+ regulator-always-on;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+ };
+
+ partitions: partitions {
+ parts = <1>;
+ part-0 = <&rootfs>;
+ rootfs: rootfs {
+ pname = "rootfs";
+ size = <0xffffffff 0xffffffff>;
+ mask = <4>;
+ };
+ };
+
+ efusekey: efusekey {
+ keynum = <5>;
+ key0 = <&key_0>;
+ key1 = <&key_1>;
+ key2 = <&key_2>;
+ key3 = <&key_3>;
+ key4 = <&key_4>;
+
+ key_0: key_0 {
+ keyname = "mac";
+ offset = <0>;
+ size = <6>;
+ };
+ key_1: key_1 {
+ keyname = "mac_bt";
+ offset = <6>;
+ size = <6>;
+ };
+ key_2: key_2 {
+ keyname = "mac_wifi";
+ offset = <12>;
+ size = <6>;
+ };
+ key_3: key_3 {
+ keyname = "usid";
+ offset = <18>;
+ size = <32>;
+ };
+ key_4: key_4 {
+ keyname = "serial";
+ offset = <50>;
+ size = <32>;
+ };
+ }; //End efusekey
+
+ unifykey {
+ compatible = "amlogic, unifykey";
+ status = "ok";
+ unifykey-num = <6>;
+ unifykey-index-0 = <&keysn_0>;
+ unifykey-index-1 = <&keysn_1>;
+ unifykey-index-2 = <&keysn_2>;
+ unifykey-index-3 = <&keysn_3>;
+ unifykey-index-4 = <&keysn_4>;
+ unifykey-index-5 = <&keysn_5>;
+
+ keysn_0: key_0 {
+ key-name = "usid";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_1: key_1 {
+ key-name = "mac";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_2: key_2 {
+ key-name = "mac_bt";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ key-type = "mac";
+ };
+ keysn_3: key_3 {
+ key-name = "mac_wifi";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ key-type = "mac";
+ };
+ keysn_4: key_4 {
+ key-name = "serial";
+ key-device = "normal";
+ key-permit = "read";
+ };
+ keysn_5:key_5 {
+ key-name = "deviceid";
+ key-device = "normal";
+ key-permit = "read","write","del";
+ };
+ }; //End unifykey
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&scpi_sensors 0>;
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+ cpu_hot: cpu-hot {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+ cpu_critical: cpu-critical {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+ cpu_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+};
+
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_rmii_x_pins>;
+ pinctrl-names = "default";
+ phy-handle = <ð_phy0>;
+ phy-mode = "rmii";
+ internal_phy=<0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+ eth_phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0243.0c54";
+ max-speed = <100>;
+ reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+ reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+ status = "okay";
+ pinctrl-0 = <&i2c1_z_pins>;
+ pinctrl-names = "default";
+
+ /* RTC */
+ pcf8563: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ status = "okay";
+ };
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_ab {
+ status = "okay";
+ pinctrl-0 = <&pwm_a_x20_pins>;
+ pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* emmc storage */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+ status = "okay";
+ pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* UART Console */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_b_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+ status = "okay";
+};
+
+&audio {
+ status = "disabled";
+};
+
+&efuse {
+ status = "okay";
+ compatible = "amlogic,meson-gxbb-efuse", "amlogic, efuse";
+ read_cmd = <0x82000030>;
+ write_cmd = <0x82000031>;
+ get_max_cmd = <0x82000033>;
+ key = <&efusekey>;
+ clock-names = "efuse_clk";
+};
+
+&gpio {
+ interrupt-parent = <&gpio_intc>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-line-names =
+ "", "", "", "", "", // 0 - 4
+ "", "", "", "", "", // 5 - 9
+ "UserButton", "", "", "", "", // 10 - 14
+ "", "", "", "", "", // 15 - 19
+ "", "", "", "", "", // 20 - 24
+ "", "LEDRED", "LEDGREEN", "Output3", "Output2", // 25 - 29
+ "Output1", "", "", "", "", // 30 - 34
+ "", "ZigBeeBOOT", "", "", "", // 35 - 39
+ "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+ "Input2", "Input1", "", "", "", // 45 - 49
+ "", "", "", "", "", // 50 - 54
+ "", "", "", "", "", // 55 - 59
+ "", "", "", "", "", // 60 - 64
+ "", "", "", "", "", // 65 - 69
+ "", "", "", "", "", // 70 - 74
+ "", "", "", "", "", // 75 - 79
+ "", "", "", "", "", // 80 - 84
+ "", ""; // 85-86
+};
+
+&cpu0 {
+ #cooling-cells = <2>;
+};
+
+&cpu1 {
+ #cooling-cells = <2>;
+};
+
+&cpu2 {
+ #cooling-cells = <2>;
+};
+
+&cpu3 {
+ #cooling-cells = <2>;
+};
+
--
2.30.2
next prev parent reply other threads:[~2021-09-02 13:06 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-09-02 13:05 [PATCH 0/3] arm64: meson-axg: meson-gxl: add support for JetHub D1/H1 Vyacheslav Bocharov
2021-09-02 13:05 ` Vyacheslav Bocharov
2021-09-02 13:05 ` Vyacheslav Bocharov
2021-09-02 13:05 ` [PATCH 1/3] arm64: dts: meson-gxl: add support for JetHub H1 Vyacheslav Bocharov
2021-09-02 13:05 ` Vyacheslav Bocharov
2021-09-02 13:05 ` Vyacheslav Bocharov
2021-09-02 13:19 ` Neil Armstrong
2021-09-02 13:19 ` Neil Armstrong
2021-09-02 13:19 ` Neil Armstrong
2021-09-03 6:05 ` Vyacheslav
2021-09-02 13:05 ` Vyacheslav Bocharov [this message]
2021-09-02 13:05 ` [PATCH 2/3] arm64: dts: meson-axg: add support for JetHub D1 Vyacheslav Bocharov
2021-09-02 13:05 ` Vyacheslav Bocharov
2021-09-02 13:27 ` Neil Armstrong
2021-09-02 13:27 ` Neil Armstrong
2021-09-02 13:27 ` Neil Armstrong
2021-09-02 13:05 ` [PATCH 3/3] dt-bindings: arm: amlogic: add bindings for JetHub D1/H1 Vyacheslav Bocharov
2021-09-02 13:05 ` Vyacheslav Bocharov
2021-09-02 13:05 ` Vyacheslav Bocharov
2021-09-02 13:29 ` Neil Armstrong
2021-09-02 13:29 ` Neil Armstrong
2021-09-02 13:29 ` Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210902130516.3892452-3-adeep@lexina.in \
--to=adeep@lexina.in \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=narmstrong@baylibre.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.