[PATCH] mmc: sdhci: Map more voltage level to SDHCI_POWER_330

[Shawn Guo <shawn.guo@linaro.org>]

On Thundercomm TurboX CM2290, the eMMC OCR reports vdd = 23 (3.5 ~ 3.6 V),
which is being treated as an invalid value by sdhci_set_power_noreg().
And thus eMMC is totally broken on the platform.

[    1.436599] ------------[ cut here ]------------
[    1.436606] mmc0: Invalid vdd 0x17
[    1.436640] WARNING: CPU: 2 PID: 69 at drivers/mmc/host/sdhci.c:2048 sdhci_set_power_noreg+0x168/0x2b4
[    1.436655] Modules linked in:
[    1.436662] CPU: 2 PID: 69 Comm: kworker/u8:1 Tainted: G        W         5.15.0-rc1+ #137
[    1.436669] Hardware name: Thundercomm TurboX CM2290 (DT)
[    1.436674] Workqueue: events_unbound async_run_entry_fn
[    1.436685] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    1.436692] pc : sdhci_set_power_noreg+0x168/0x2b4
[    1.436698] lr : sdhci_set_power_noreg+0x168/0x2b4
[    1.436703] sp : ffff800010803a60
[    1.436705] x29: ffff800010803a60 x28: ffff6a9102465f00 x27: ffff6a9101720a70
[    1.436715] x26: ffff6a91014de1c0 x25: ffff6a91014de010 x24: ffff6a91016af280
[    1.436724] x23: ffffaf7b1b276640 x22: 0000000000000000 x21: ffff6a9101720000
[    1.436733] x20: ffff6a9101720370 x19: ffff6a9101720580 x18: 0000000000000020
[    1.436743] x17: 0000000000000000 x16: 0000000000000004 x15: ffffffffffffffff
[    1.436751] x14: 0000000000000000 x13: 00000000fffffffd x12: ffffaf7b1b84b0bc
[    1.436760] x11: ffffaf7b1b720d10 x10: 000000000000000a x9 : ffff800010803a60
[    1.436769] x8 : 000000000000000a x7 : 000000000000000f x6 : 00000000fffff159
[    1.436778] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000ffffffff
[    1.436787] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff6a9101718d80
[    1.436797] Call trace:
[    1.436800]  sdhci_set_power_noreg+0x168/0x2b4
[    1.436805]  sdhci_set_ios+0xa0/0x7fc
[    1.436811]  mmc_power_up.part.0+0xc4/0x164
[    1.436818]  mmc_start_host+0xa0/0xb0
[    1.436824]  mmc_add_host+0x60/0x90
[    1.436830]  __sdhci_add_host+0x174/0x330
[    1.436836]  sdhci_msm_probe+0x7c0/0x920
[    1.436842]  platform_probe+0x68/0xe0
[    1.436850]  really_probe.part.0+0x9c/0x31c
[    1.436857]  __driver_probe_device+0x98/0x144
[    1.436863]  driver_probe_device+0xc8/0x15c
[    1.436869]  __device_attach_driver+0xb4/0x120
[    1.436875]  bus_for_each_drv+0x78/0xd0
[    1.436881]  __device_attach_async_helper+0xac/0xd0
[    1.436888]  async_run_entry_fn+0x34/0x110
[    1.436895]  process_one_work+0x1d0/0x354
[    1.436903]  worker_thread+0x13c/0x470
[    1.436910]  kthread+0x150/0x160
[    1.436915]  ret_from_fork+0x10/0x20
[    1.436923] ---[ end trace fcfac44cb045c3a8 ]---

Fix the issue by mapping MMC_VDD_35_36 (and MMC_VDD_34_35) to
SDHCI_POWER_330 as well.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
Changes since RFC:
- Add a comment for 3.4 ~ 3.6V voltage range.

 drivers/mmc/host/sdhci.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 8eefa7d5fe85..2d80a04e11d8 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -2042,6 +2042,12 @@ void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
 			break;
 		case MMC_VDD_32_33:
 		case MMC_VDD_33_34:
+		/*
+		 * 3.4 ~ 3.6V are valid only for those platforms where it's
+		 * known that the voltage range is supported by hardware.
+		 */
+		case MMC_VDD_34_35:
+		case MMC_VDD_35_36:
 			pwr = SDHCI_POWER_330;
 			break;
 		default:
-- 
2.17.1