From: Martin Kaiser <martin@kaiser.cx>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>,
Phillip Potter <phil@philpotter.co.uk>,
Michael Straube <straube.linux@gmail.com>,
linux-staging@lists.linux.dev, linux-kernel@vger.kernel.org,
Martin Kaiser <martin@kaiser.cx>
Subject: [PATCH 3/9] staging: r8188: remove cut mask from power transitions
Date: Sun, 19 Dec 2021 19:39:20 +0100 [thread overview]
Message-ID: <20211219183926.4746-4-martin@kaiser.cx> (raw)
In-Reply-To: <20211219183926.4746-1-martin@kaiser.cx>
Remove the power cut mask from the steps of the power transitions.
The power cut mask is not used, all values are allowed for all steps.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
---
drivers/staging/r8188eu/hal/HalPwrSeqCmd.c | 5 +-
drivers/staging/r8188eu/hal/usb_halinit.c | 6 +-
.../staging/r8188eu/include/Hal8188EPwrSeq.h | 72 +++++++++----------
.../staging/r8188eu/include/HalPwrSeqCmd.h | 17 +----
4 files changed, 42 insertions(+), 58 deletions(-)
diff --git a/drivers/staging/r8188eu/hal/HalPwrSeqCmd.c b/drivers/staging/r8188eu/hal/HalPwrSeqCmd.c
index 0fd11aca7ac7..f64b5352f043 100644
--- a/drivers/staging/r8188eu/hal/HalPwrSeqCmd.c
+++ b/drivers/staging/r8188eu/hal/HalPwrSeqCmd.c
@@ -25,7 +25,7 @@ Major Change History:
* Assumption:
* We should follow specific format which was released from HW SD.
*/
-u8 HalPwrSeqCmdParsing(struct adapter *padapter, u8 cut_vers, u8 fab_vers,
+u8 HalPwrSeqCmdParsing(struct adapter *padapter, u8 fab_vers,
u8 ifacetype, struct wl_pwr_cfg pwrseqcmd[])
{
struct wl_pwr_cfg pwrcfgcmd = {0};
@@ -39,9 +39,8 @@ u8 HalPwrSeqCmdParsing(struct adapter *padapter, u8 cut_vers, u8 fab_vers,
do {
pwrcfgcmd = pwrseqcmd[aryidx];
- /* 2 Only Handle the command whose FAB, CUT, and Interface are matched */
+ /* 2 Only Handle the command whose FAB and Interface are matched */
if ((GET_PWR_CFG_FAB_MASK(pwrcfgcmd) & fab_vers) &&
- (GET_PWR_CFG_CUT_MASK(pwrcfgcmd) & cut_vers) &&
(GET_PWR_CFG_INTF_MASK(pwrcfgcmd) & ifacetype)) {
switch (GET_PWR_CFG_CMD(pwrcfgcmd)) {
case PWR_CMD_WRITE:
diff --git a/drivers/staging/r8188eu/hal/usb_halinit.c b/drivers/staging/r8188eu/hal/usb_halinit.c
index 40227078c4b6..528a53d3e61e 100644
--- a/drivers/staging/r8188eu/hal/usb_halinit.c
+++ b/drivers/staging/r8188eu/hal/usb_halinit.c
@@ -78,7 +78,7 @@ u32 rtl8188eu_InitPowerOn(struct adapter *adapt)
if (haldata->bMacPwrCtrlOn)
return _SUCCESS;
- if (!HalPwrSeqCmdParsing(adapt, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8188E_NIC_PWR_ON_FLOW)) {
+ if (!HalPwrSeqCmdParsing(adapt, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8188E_NIC_PWR_ON_FLOW)) {
DBG_88E(KERN_ERR "%s: run power on flow fail\n", __func__);
return _FAIL;
}
@@ -824,7 +824,7 @@ static void CardDisableRTL8188EU(struct adapter *Adapter)
rtw_write8(Adapter, REG_CR, 0x0);
/* Run LPS WL RFOFF flow */
- HalPwrSeqCmdParsing(Adapter, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8188E_NIC_LPS_ENTER_FLOW);
+ HalPwrSeqCmdParsing(Adapter, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8188E_NIC_LPS_ENTER_FLOW);
/* 2. 0x1F[7:0] = 0 turn off RF */
@@ -845,7 +845,7 @@ static void CardDisableRTL8188EU(struct adapter *Adapter)
rtw_write8(Adapter, REG_32K_CTRL, val8 & (~BIT(0)));
/* Card disable power action flow */
- HalPwrSeqCmdParsing(Adapter, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8188E_NIC_DISABLE_FLOW);
+ HalPwrSeqCmdParsing(Adapter, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, Rtl8188E_NIC_DISABLE_FLOW);
/* Reset MCU IO Wrapper */
val8 = rtw_read8(Adapter, REG_RSV_CTRL + 1);
diff --git a/drivers/staging/r8188eu/include/Hal8188EPwrSeq.h b/drivers/staging/r8188eu/include/Hal8188EPwrSeq.h
index d36a2ab2ec7b..c1da4a4bf9c9 100644
--- a/drivers/staging/r8188eu/include/Hal8188EPwrSeq.h
+++ b/drivers/staging/r8188eu/include/Hal8188EPwrSeq.h
@@ -8,55 +8,55 @@
#define RTL8188E_TRANS_CARDEMU_TO_ACT \
/* format */ \
- /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
- {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},/* wait till 0x04[17] = 1 power ready*/ \
- {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0)|BIT(1), 0}, /* 0x02[1:0] = 0 reset BB*/ \
- {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)}, /*0x24[23] = 2b'01 schmit trigger */ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0}, /* 0x04[15] = 0 disable HWPDN (control by DRV)*/\
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4)|BIT(3), 0}, /*0x04[12:11] = 2b'00 disable WL suspend*/ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x04[8] = 1 polling until return 0*/ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0}, /*wait till 0x04[8] = 0*/ \
- {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*LDO normal mode*/ \
- {0x0074, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*SDIO Driving*/ \
+ /* { offset, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
+ {0x0006, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},/* wait till 0x04[17] = 1 power ready*/ \
+ {0x0002, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0)|BIT(1), 0}, /* 0x02[1:0] = 0 reset BB*/ \
+ {0x0026, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)}, /*0x24[23] = 2b'01 schmit trigger */ \
+ {0x0005, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0}, /* 0x04[15] = 0 disable HWPDN (control by DRV)*/\
+ {0x0005, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4)|BIT(3), 0}, /*0x04[12:11] = 2b'00 disable WL suspend*/ \
+ {0x0005, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x04[8] = 1 polling until return 0*/ \
+ {0x0005, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0}, /*wait till 0x04[8] = 0*/ \
+ {0x0023, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*LDO normal mode*/ \
+ {0x0074, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*SDIO Driving*/ \
#define RTL8188E_TRANS_ACT_TO_CARDEMU \
/* format */ \
- /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
- {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \
- {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*LDO Sleep mode*/ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
+ /* { offset, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
+ {0x001F, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \
+ {0x0023, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*LDO Sleep mode*/ \
+ {0x0005, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
+ {0x0005, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
#define RTL8188E_TRANS_CARDEMU_TO_CARDDIS \
/* format */ \
- /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
- {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)}, /*0x24[23] = 2b'01 schmit trigger */ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
- {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */ \
- {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*Clear SIC_EN register 0x40[12] = 1'b0 */ \
- {0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*Set USB suspend enable local register 0xfe10[4]=1 */ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
+ /* { offset, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
+ {0x0026, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)}, /*0x24[23] = 2b'01 schmit trigger */ \
+ {0x0005, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x0007, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */ \
+ {0x0041, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*Clear SIC_EN register 0x40[12] = 1'b0 */ \
+ {0xfe10, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*Set USB suspend enable local register 0xfe10[4]=1 */ \
+ {0x0086, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
+ {0x0086, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
/* This is used by driver for LPSRadioOff Procedure, not for FW LPS Step */
#define RTL8188E_TRANS_ACT_TO_LPS \
/* format */ \
- /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here */ \
- {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \
- {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
- {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
- {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
- {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
- {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/*CCK and OFDM are disabled,and clock are gated*/ \
- {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
- {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \
- {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \
- {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)},/*Respond TxOK to scheduler*/ \
+ /* { offset, fab_msk|interface_msk, base|cmd, msk, value }, comments here */ \
+ {0x0522, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \
+ {0x05F8, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05F9, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FA, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x05FB, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \
+ {0x0002, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/*CCK and OFDM are disabled,and clock are gated*/ \
+ {0x0002, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
+ {0x0100, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \
+ {0x0101, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \
+ {0x0553, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)},/*Respond TxOK to scheduler*/ \
#define RTL8188E_TRANS_END \
/* format */ \
- /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
- {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0, PWR_CMD_END, 0, 0}, /* */
+ /* { offset, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/ \
+ {0xFFFF, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0, PWR_CMD_END, 0, 0}, /* */
extern struct wl_pwr_cfg rtl8188E_power_on_flow[];
extern struct wl_pwr_cfg rtl8188E_card_disable_flow[];
diff --git a/drivers/staging/r8188eu/include/HalPwrSeqCmd.h b/drivers/staging/r8188eu/include/HalPwrSeqCmd.h
index fe7ac910beb8..f82860bd0e83 100644
--- a/drivers/staging/r8188eu/include/HalPwrSeqCmd.h
+++ b/drivers/staging/r8188eu/include/HalPwrSeqCmd.h
@@ -65,19 +65,6 @@
#define PWR_FAB_UMC_MSK BIT(1)
#define PWR_FAB_ALL_MSK (BIT(0)|BIT(1)|BIT(2)|BIT(3))
-/*---------------------------------------------*/
-/* 3 The value of cut_msk: 8 bits */
-/*---------------------------------------------*/
-#define PWR_CUT_TESTCHIP_MSK BIT(0)
-#define PWR_CUT_A_MSK BIT(1)
-#define PWR_CUT_B_MSK BIT(2)
-#define PWR_CUT_C_MSK BIT(3)
-#define PWR_CUT_D_MSK BIT(4)
-#define PWR_CUT_E_MSK BIT(5)
-#define PWR_CUT_F_MSK BIT(6)
-#define PWR_CUT_G_MSK BIT(7)
-#define PWR_CUT_ALL_MSK 0xFF
-
enum pwrseq_cmd_delat_unit {
PWRSEQ_DELAY_US,
PWRSEQ_DELAY_MS,
@@ -85,7 +72,6 @@ enum pwrseq_cmd_delat_unit {
struct wl_pwr_cfg {
u16 offset;
- u8 cut_msk;
u8 fab_msk:4;
u8 interface_msk:4;
u8 base:4;
@@ -95,7 +81,6 @@ struct wl_pwr_cfg {
};
#define GET_PWR_CFG_OFFSET(__PWR_CMD) __PWR_CMD.offset
-#define GET_PWR_CFG_CUT_MASK(__PWR_CMD) __PWR_CMD.cut_msk
#define GET_PWR_CFG_FAB_MASK(__PWR_CMD) __PWR_CMD.fab_msk
#define GET_PWR_CFG_INTF_MASK(__PWR_CMD) __PWR_CMD.interface_msk
#define GET_PWR_CFG_BASE(__PWR_CMD) __PWR_CMD.base
@@ -104,7 +89,7 @@ struct wl_pwr_cfg {
#define GET_PWR_CFG_VALUE(__PWR_CMD) __PWR_CMD.value
/* Prototype of protected function. */
-u8 HalPwrSeqCmdParsing(struct adapter *padapter, u8 CutVersion, u8 FabVersion,
+u8 HalPwrSeqCmdParsing(struct adapter *padapter, u8 FabVersion,
u8 InterfaceType, struct wl_pwr_cfg PwrCfgCmd[]);
#endif
--
2.20.1
next prev parent reply other threads:[~2021-12-19 18:39 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-19 18:39 [PATCH 0/9] staging: r8188: clean up the power state transitions Martin Kaiser
2021-12-19 18:39 ` [PATCH 1/9] staging: r8188: remove unused power transitions Martin Kaiser
2021-12-19 18:39 ` [PATCH 2/9] staging: r8188: remove sizes from power transition arrays Martin Kaiser
2021-12-19 18:39 ` Martin Kaiser [this message]
2021-12-19 18:39 ` [PATCH 4/9] staging: r8188: remove fab mask from power transitions Martin Kaiser
2021-12-19 18:39 ` [PATCH 5/9] staging: r8188: remove interface " Martin Kaiser
2021-12-19 18:39 ` [PATCH 6/9] staging: r8188: remove base address " Martin Kaiser
2021-12-19 18:39 ` [PATCH 7/9] staging: r8188: remove unused power command Martin Kaiser
2021-12-19 18:39 ` [PATCH 8/9] staging: r8188: reformat the power transition steps Martin Kaiser
2021-12-19 18:39 ` [PATCH 9/9] staging: r8188: move the steps into Hal8188EPwrSeq.c Martin Kaiser
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211219183926.4746-4-martin@kaiser.cx \
--to=martin@kaiser.cx \
--cc=Larry.Finger@lwfinger.net \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-staging@lists.linux.dev \
--cc=phil@philpotter.co.uk \
--cc=straube.linux@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.