All of lore.kernel.org
 help / color / mirror / Atom feed
From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
To: Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
	linux-serial@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Jiri Slaby <jirislaby@kernel.org>, Qing Wang <wangqing@vivo.com>
Subject: [PATCH v3 1/1] serial: 8250_lpss: Balance reference count for PCI DMA device
Date: Wed, 23 Feb 2022 17:12:40 +0200	[thread overview]
Message-ID: <20220223151240.70248-1-andriy.shevchenko@linux.intel.com> (raw)

The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().

Fixes: 9a1870ce812e ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on: a13e19cf3dc1 ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
v3: split out as independent patch from the series (the rest is under discussion)
 drivers/tty/serial/8250/8250_lpss.c | 28 ++++++++++++++++++++++------
 1 file changed, 22 insertions(+), 6 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c
index d3bafec7619d..0f5af061e0b4 100644
--- a/drivers/tty/serial/8250/8250_lpss.c
+++ b/drivers/tty/serial/8250/8250_lpss.c
@@ -117,8 +117,7 @@ static int byt_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 {
 	struct dw_dma_slave *param = &lpss->dma_param;
 	struct pci_dev *pdev = to_pci_dev(port->dev);
-	unsigned int dma_devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0);
-	struct pci_dev *dma_dev = pci_get_slot(pdev->bus, dma_devfn);
+	struct pci_dev *dma_dev;
 
 	switch (pdev->device) {
 	case PCI_DEVICE_ID_INTEL_BYT_UART1:
@@ -137,6 +136,8 @@ static int byt_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 		return -EINVAL;
 	}
 
+	dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
+
 	param->dma_dev = &dma_dev->dev;
 	param->m_master = 0;
 	param->p_master = 1;
@@ -152,6 +153,14 @@ static int byt_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 	return 0;
 }
 
+static void byt_serial_exit(struct lpss8250 *lpss)
+{
+	struct dw_dma_slave *param = &lpss->dma_param;
+
+	/* Paired with pci_get_slot() in the byt_serial_setup() above */
+	put_device(param->dma_dev);
+}
+
 static int ehl_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 {
 	struct uart_8250_dma *dma = &lpss->data.dma;
@@ -170,6 +179,13 @@ static int ehl_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 	return 0;
 }
 
+static void ehl_serial_exit(struct lpss8250 *lpss)
+{
+	struct uart_8250_port *up = serial8250_get_port(lpss->data.line);
+
+	up->dma = NULL;
+}
+
 #ifdef CONFIG_SERIAL_8250_DMA
 static const struct dw_dma_platform_data qrk_serial_dma_pdata = {
 	.nr_channels = 2,
@@ -344,8 +360,7 @@ static int lpss8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	return 0;
 
 err_exit:
-	if (lpss->board->exit)
-		lpss->board->exit(lpss);
+	lpss->board->exit(lpss);
 	pci_free_irq_vectors(pdev);
 	return ret;
 }
@@ -356,8 +371,7 @@ static void lpss8250_remove(struct pci_dev *pdev)
 
 	serial8250_unregister_port(lpss->data.line);
 
-	if (lpss->board->exit)
-		lpss->board->exit(lpss);
+	lpss->board->exit(lpss);
 	pci_free_irq_vectors(pdev);
 }
 
@@ -365,12 +379,14 @@ static const struct lpss8250_board byt_board = {
 	.freq = 100000000,
 	.base_baud = 2764800,
 	.setup = byt_serial_setup,
+	.exit = byt_serial_exit,
 };
 
 static const struct lpss8250_board ehl_board = {
 	.freq = 200000000,
 	.base_baud = 12500000,
 	.setup = ehl_serial_setup,
+	.exit = ehl_serial_exit,
 };
 
 static const struct lpss8250_board qrk_board = {
-- 
2.34.1


                 reply	other threads:[~2022-02-23 15:12 UTC|newest]

Thread overview: [no followups] expand[flat|nested]  mbox.gz  Atom feed

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220223151240.70248-1-andriy.shevchenko@linux.intel.com \
    --to=andriy.shevchenko@linux.intel.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=jirislaby@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-serial@vger.kernel.org \
    --cc=wangqing@vivo.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.