From: qianfanguijin@163.com To: linux-sunxi@lists.linux.dev Cc: Rob Herring <robh+dt@kernel.org>, Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Jernej Skrabec <jernej.skrabec@gmail.com>, "Rafael J . Wysocki" <rafael@kernel.org>, Viresh Kumar <viresh.kumar@linaro.org>, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org, qianfan Zhao <qianfanguijin@163.com> Subject: [PATCH v5 3/3] ARM: dts: sun8i-r40: Add thermal trip points/cooling maps Date: Tue, 17 May 2022 09:36:07 +0800 [thread overview] Message-ID: <20220517013607.2252-4-qianfanguijin@163.com> (raw) In-Reply-To: <20220517013607.2252-1-qianfanguijin@163.com> From: qianfan Zhao <qianfanguijin@163.com> For the trip points, I used values from the BSP code. The critical trip point value is 30°C above the maximum recommended ambient temperature (85°C) for the SoC from the datasheet, so there's some headroom even at such a high ambient temperature. Signed-off-by: qianfan Zhao <qianfanguijin@163.com> --- arch/arm/boot/dts/sun8i-r40.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi index ae2a5ebd9924..b43f3f72a915 100644 --- a/arch/arm/boot/dts/sun8i-r40.dtsi +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -86,6 +86,7 @@ cpu0: cpu@0 { reg = <0>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; cpu1: cpu@1 { @@ -94,6 +95,7 @@ cpu1: cpu@1 { reg = <1>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; cpu2: cpu@2 { @@ -102,6 +104,7 @@ cpu2: cpu@2 { reg = <2>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; cpu3: cpu@3 { @@ -110,6 +113,7 @@ cpu3: cpu@3 { reg = <3>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; }; @@ -125,6 +129,30 @@ cpu_thermal: cpu0-thermal { polling-delay-passive = <0>; polling-delay = <0>; thermal-sensors = <&ths 0>; + + trips { + cpu_hot_trip: cpu-hot { + temperature = <80000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_very_hot_trip: cpu-very-hot { + temperature = <115000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + cpu-hot-limit { + trip = <&cpu_hot_trip>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; gpu_thermal: gpu-thermal { -- 2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: qianfanguijin@163.com To: linux-sunxi@lists.linux.dev Cc: Rob Herring <robh+dt@kernel.org>, Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Jernej Skrabec <jernej.skrabec@gmail.com>, "Rafael J . Wysocki" <rafael@kernel.org>, Viresh Kumar <viresh.kumar@linaro.org>, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org, qianfan Zhao <qianfanguijin@163.com> Subject: [PATCH v5 3/3] ARM: dts: sun8i-r40: Add thermal trip points/cooling maps Date: Tue, 17 May 2022 09:36:07 +0800 [thread overview] Message-ID: <20220517013607.2252-4-qianfanguijin@163.com> (raw) In-Reply-To: <20220517013607.2252-1-qianfanguijin@163.com> From: qianfan Zhao <qianfanguijin@163.com> For the trip points, I used values from the BSP code. The critical trip point value is 30°C above the maximum recommended ambient temperature (85°C) for the SoC from the datasheet, so there's some headroom even at such a high ambient temperature. Signed-off-by: qianfan Zhao <qianfanguijin@163.com> --- arch/arm/boot/dts/sun8i-r40.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi index ae2a5ebd9924..b43f3f72a915 100644 --- a/arch/arm/boot/dts/sun8i-r40.dtsi +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -86,6 +86,7 @@ cpu0: cpu@0 { reg = <0>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; cpu1: cpu@1 { @@ -94,6 +95,7 @@ cpu1: cpu@1 { reg = <1>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; cpu2: cpu@2 { @@ -102,6 +104,7 @@ cpu2: cpu@2 { reg = <2>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; cpu3: cpu@3 { @@ -110,6 +113,7 @@ cpu3: cpu@3 { reg = <3>; clocks = <&ccu CLK_CPU>; clock-names = "cpu"; + #cooling-cells = <2>; }; }; @@ -125,6 +129,30 @@ cpu_thermal: cpu0-thermal { polling-delay-passive = <0>; polling-delay = <0>; thermal-sensors = <&ths 0>; + + trips { + cpu_hot_trip: cpu-hot { + temperature = <80000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_very_hot_trip: cpu-very-hot { + temperature = <115000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + cpu-hot-limit { + trip = <&cpu_hot_trip>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; gpu_thermal: gpu-thermal { -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-05-17 1:53 UTC|newest] Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top 2022-05-17 1:36 [PATCH v5 0/3] ARM: sun8i-r40: CPU improve qianfanguijin 2022-05-17 1:36 ` qianfanguijin 2022-05-17 1:36 ` [PATCH v5 1/3] ARM: dts: sun8i-r40: Add "cpu-supply" node for sun8i-r40 based board qianfanguijin 2022-05-17 1:36 ` qianfanguijin 2022-07-05 4:45 ` Samuel Holland 2022-07-05 4:45 ` Samuel Holland 2022-05-17 1:36 ` [PATCH v5 2/3] ARM: dts: sun8i-r40: add opp table for cpu qianfanguijin 2022-05-17 1:36 ` qianfanguijin 2022-07-05 4:57 ` Samuel Holland 2022-07-05 4:57 ` Samuel Holland 2022-05-17 1:36 ` qianfanguijin [this message] 2022-05-17 1:36 ` [PATCH v5 3/3] ARM: dts: sun8i-r40: Add thermal trip points/cooling maps qianfanguijin 2022-07-05 5:07 ` Samuel Holland 2022-07-05 5:07 ` Samuel Holland 2022-07-05 19:41 ` [PATCH v5 0/3] ARM: sun8i-r40: CPU improve Jernej Škrabec 2022-07-05 19:41 ` Jernej Škrabec
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20220517013607.2252-4-qianfanguijin@163.com \ --to=qianfanguijin@163.com \ --cc=devicetree@vger.kernel.org \ --cc=jernej.skrabec@gmail.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-pm@vger.kernel.org \ --cc=linux-sunxi@lists.linux.dev \ --cc=mripard@kernel.org \ --cc=rafael@kernel.org \ --cc=robh+dt@kernel.org \ --cc=viresh.kumar@linaro.org \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.