All of lore.kernel.org
 help / color / mirror / Atom feed
From: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
To: Jaroslav Kysela <perex@perex.cz>, Takashi Iwai <tiwai@suse.com>,
	Mark Brown <broonie@kernel.org>
Cc: <alsa-devel@alsa-project.org>, <patches@opensource.cirrus.com>,
	<linux-kernel@vger.kernel.org>,
	Stefan Binding <sbinding@opensource.cirrus.com>
Subject: [PATCH v3 15/17] ALSA: hda: cs35l41: Add defaulted values into dsp bypass config sequence
Date: Thu, 19 May 2022 18:47:47 +0100	[thread overview]
Message-ID: <20220519174749.15459-16-vitalyr@opensource.cirrus.com> (raw)
In-Reply-To: <20220519174749.15459-1-vitalyr@opensource.cirrus.com>

From: Stefan Binding <sbinding@opensource.cirrus.com>

The config sequences for running with and without firmware and DSP
are different. The original behavior assumed that we would only
run without DSP only in the case where firmware load failed.
This meant the non-firmware sequence was written with the assumtion
that various registers would be set to their default value.
However, to support the ability to unload the firmware, the
non-firmware register sequence must be updated to update all
required registers, including values that would be defaulted,
in case the firmware sequence, which could have already run,
has changed their value.

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
---

Changes since v2:
 - No change
 
 sound/pci/hda/cs35l41_hda.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/sound/pci/hda/cs35l41_hda.c b/sound/pci/hda/cs35l41_hda.c
index 016f97f61c34..4ca5c7b974ce 100644
--- a/sound/pci/hda/cs35l41_hda.c
+++ b/sound/pci/hda/cs35l41_hda.c
@@ -32,11 +32,24 @@
 
 static const struct reg_sequence cs35l41_hda_config[] = {
 	{ CS35L41_PLL_CLK_CTRL,		0x00000430 }, // 3072000Hz, BCLK Input, PLL_REFCLK_EN = 1
+	{ CS35L41_DSP_CLK_CTRL,		0x00000003 }, // DSP CLK EN
 	{ CS35L41_GLOBAL_CLK_CTRL,	0x00000003 }, // GLOBAL_FS = 48 kHz
 	{ CS35L41_SP_ENABLES,		0x00010000 }, // ASP_RX1_EN = 1
 	{ CS35L41_SP_RATE_CTRL,		0x00000021 }, // ASP_BCLK_FREQ = 3.072 MHz
 	{ CS35L41_SP_FORMAT,		0x20200200 }, // 32 bits RX/TX slots, I2S, clk consumer
+	{ CS35L41_SP_HIZ_CTRL,		0x00000002 }, // Hi-Z unused
+	{ CS35L41_SP_TX_WL,		0x00000018 }, // 24 cycles/slot
+	{ CS35L41_SP_RX_WL,		0x00000018 }, // 24 cycles/slot
 	{ CS35L41_DAC_PCM1_SRC,		0x00000008 }, // DACPCM1_SRC = ASPRX1
+	{ CS35L41_ASP_TX1_SRC,		0x00000018 }, // ASPTX1 SRC = VMON
+	{ CS35L41_ASP_TX2_SRC,		0x00000019 }, // ASPTX2 SRC = IMON
+	{ CS35L41_ASP_TX3_SRC,		0x00000032 }, // ASPTX3 SRC = ERRVOL
+	{ CS35L41_ASP_TX4_SRC,		0x00000033 }, // ASPTX4 SRC = CLASSH_TGT
+	{ CS35L41_DSP1_RX1_SRC,		0x00000008 }, // DSP1RX1 SRC = ASPRX1
+	{ CS35L41_DSP1_RX2_SRC,		0x00000009 }, // DSP1RX2 SRC = ASPRX2
+	{ CS35L41_DSP1_RX3_SRC,         0x00000018 }, // DSP1RX3 SRC = VMON
+	{ CS35L41_DSP1_RX4_SRC,         0x00000019 }, // DSP1RX4 SRC = IMON
+	{ CS35L41_DSP1_RX5_SRC,         0x00000020 }, // DSP1RX5 SRC = ERRVOL
 	{ CS35L41_AMP_DIG_VOL_CTRL,	0x00000000 }, // AMP_VOL_PCM  0.0 dB
 	{ CS35L41_AMP_GAIN_CTRL,	0x00000084 }, // AMP_GAIN_PCM 4.5 dB
 };
-- 
2.34.1


WARNING: multiple messages have this Message-ID (diff)
From: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
To: Jaroslav Kysela <perex@perex.cz>, Takashi Iwai <tiwai@suse.com>,
	Mark Brown <broonie@kernel.org>
Cc: patches@opensource.cirrus.com, alsa-devel@alsa-project.org,
	linux-kernel@vger.kernel.org,
	Stefan Binding <sbinding@opensource.cirrus.com>
Subject: [PATCH v3 15/17] ALSA: hda: cs35l41: Add defaulted values into dsp bypass config sequence
Date: Thu, 19 May 2022 18:47:47 +0100	[thread overview]
Message-ID: <20220519174749.15459-16-vitalyr@opensource.cirrus.com> (raw)
In-Reply-To: <20220519174749.15459-1-vitalyr@opensource.cirrus.com>

From: Stefan Binding <sbinding@opensource.cirrus.com>

The config sequences for running with and without firmware and DSP
are different. The original behavior assumed that we would only
run without DSP only in the case where firmware load failed.
This meant the non-firmware sequence was written with the assumtion
that various registers would be set to their default value.
However, to support the ability to unload the firmware, the
non-firmware register sequence must be updated to update all
required registers, including values that would be defaulted,
in case the firmware sequence, which could have already run,
has changed their value.

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
---

Changes since v2:
 - No change
 
 sound/pci/hda/cs35l41_hda.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/sound/pci/hda/cs35l41_hda.c b/sound/pci/hda/cs35l41_hda.c
index 016f97f61c34..4ca5c7b974ce 100644
--- a/sound/pci/hda/cs35l41_hda.c
+++ b/sound/pci/hda/cs35l41_hda.c
@@ -32,11 +32,24 @@
 
 static const struct reg_sequence cs35l41_hda_config[] = {
 	{ CS35L41_PLL_CLK_CTRL,		0x00000430 }, // 3072000Hz, BCLK Input, PLL_REFCLK_EN = 1
+	{ CS35L41_DSP_CLK_CTRL,		0x00000003 }, // DSP CLK EN
 	{ CS35L41_GLOBAL_CLK_CTRL,	0x00000003 }, // GLOBAL_FS = 48 kHz
 	{ CS35L41_SP_ENABLES,		0x00010000 }, // ASP_RX1_EN = 1
 	{ CS35L41_SP_RATE_CTRL,		0x00000021 }, // ASP_BCLK_FREQ = 3.072 MHz
 	{ CS35L41_SP_FORMAT,		0x20200200 }, // 32 bits RX/TX slots, I2S, clk consumer
+	{ CS35L41_SP_HIZ_CTRL,		0x00000002 }, // Hi-Z unused
+	{ CS35L41_SP_TX_WL,		0x00000018 }, // 24 cycles/slot
+	{ CS35L41_SP_RX_WL,		0x00000018 }, // 24 cycles/slot
 	{ CS35L41_DAC_PCM1_SRC,		0x00000008 }, // DACPCM1_SRC = ASPRX1
+	{ CS35L41_ASP_TX1_SRC,		0x00000018 }, // ASPTX1 SRC = VMON
+	{ CS35L41_ASP_TX2_SRC,		0x00000019 }, // ASPTX2 SRC = IMON
+	{ CS35L41_ASP_TX3_SRC,		0x00000032 }, // ASPTX3 SRC = ERRVOL
+	{ CS35L41_ASP_TX4_SRC,		0x00000033 }, // ASPTX4 SRC = CLASSH_TGT
+	{ CS35L41_DSP1_RX1_SRC,		0x00000008 }, // DSP1RX1 SRC = ASPRX1
+	{ CS35L41_DSP1_RX2_SRC,		0x00000009 }, // DSP1RX2 SRC = ASPRX2
+	{ CS35L41_DSP1_RX3_SRC,         0x00000018 }, // DSP1RX3 SRC = VMON
+	{ CS35L41_DSP1_RX4_SRC,         0x00000019 }, // DSP1RX4 SRC = IMON
+	{ CS35L41_DSP1_RX5_SRC,         0x00000020 }, // DSP1RX5 SRC = ERRVOL
 	{ CS35L41_AMP_DIG_VOL_CTRL,	0x00000000 }, // AMP_VOL_PCM  0.0 dB
 	{ CS35L41_AMP_GAIN_CTRL,	0x00000084 }, // AMP_GAIN_PCM 4.5 dB
 };
-- 
2.34.1


  parent reply	other threads:[~2022-05-19 17:48 UTC|newest]

Thread overview: 48+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-05-19 17:47 [PATCH v3 00/17] ALSA: hda: cirrus: Add initial DSP support and firmware loading Vitaly Rodionov
2022-05-19 17:47 ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 01/17] ALSA: hda: hda_cs_dsp_ctl: Add Library to support CS_DSP ALSA controls Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-20  7:50   ` Takashi Iwai
2022-05-20  7:50     ` Takashi Iwai
2022-05-20  7:55     ` Takashi Iwai
2022-05-20  7:55       ` Takashi Iwai
2022-05-19 17:47 ` [PATCH v3 02/17] ALSA: hda: hda_cs_dsp_ctl: Add apis to write the controls directly Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 03/17] ALSA: hda: cs35l41: Save codec object inside component struct Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 04/17] ALSA: hda: cs35l41: Add initial DSP support and firmware loading Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-20  8:00   ` Takashi Iwai
2022-05-20  8:00     ` Takashi Iwai
2022-05-20  8:02     ` Takashi Iwai
2022-05-20  8:02       ` Takashi Iwai
2022-05-19 17:47 ` [PATCH v3 05/17] ALSA: hda: cs35l41: Save Subsystem ID inside CS35L41 Driver Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 06/17] ALSA: hda: cs35l41: Support reading subsystem id from ACPI Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 07/17] ALSA: hda: cs35l41: Support multiple load paths for firmware Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 08/17] ALSA: hda: cs35l41: Support Speaker ID for laptops Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 09/17] ASoC: cs35l41: Move cs35l41 exit hibernate function into shared code Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 10/17] ASoC: cs35l41: Do not print error when waking from hibernation Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 11/17] ASoC: cs35l41: Add common cs35l41 enter hibernate function Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 12/17] ALSA: hda: cs35l41: Support Hibernation during Suspend Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 13/17] ALSA: hda: cs35l41: Read Speaker Calibration data from UEFI variables Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 14/17] ALSA: hda: hda_cs_dsp_ctl: Add fw id strings Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-19 17:47 ` Vitaly Rodionov [this message]
2022-05-19 17:47   ` [PATCH v3 15/17] ALSA: hda: cs35l41: Add defaulted values into dsp bypass config sequence Vitaly Rodionov
2022-05-19 17:47 ` [PATCH v3 16/17] ALSA: hda: cs35l41: Support Firmware switching and reloading Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-05-20  8:08   ` Takashi Iwai
2022-05-20  8:08     ` Takashi Iwai
2022-05-19 17:47 ` [PATCH v3 17/17] ALSA: hda: cs35l41: Add module parameter to control firmware load Vitaly Rodionov
2022-05-19 17:47   ` Vitaly Rodionov
2022-06-07 10:54 ` (subset) [PATCH v3 00/17] ALSA: hda: cirrus: Add initial DSP support and firmware loading Mark Brown
2022-06-07 10:54   ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220519174749.15459-16-vitalyr@opensource.cirrus.com \
    --to=vitalyr@opensource.cirrus.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=broonie@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=patches@opensource.cirrus.com \
    --cc=perex@perex.cz \
    --cc=sbinding@opensource.cirrus.com \
    --cc=tiwai@suse.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.