From: Guenter Roeck <linux@roeck-us.net>
To: linux-hwmon@vger.kernel.org
Cc: linux-kernel@vger.kernel.org, Jean Delvare <jdelvare@suse.com>,
Slawomir Stepien <sst@poczta.fm>,
Guenter Roeck <linux@roeck-us.net>
Subject: [PATCH 05/40] hwmon: (lm90) Use BIT macro
Date: Wed, 25 May 2022 06:56:34 -0700 [thread overview]
Message-ID: <20220525135709.2899592-6-linux@roeck-us.net> (raw)
In-Reply-To: <20220525135709.2899592-1-linux@roeck-us.net>
Use BIT macro instead of shift operation to improve readability.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
---
drivers/hwmon/lm90.c | 55 ++++++++++++++++++++++----------------------
1 file changed, 28 insertions(+), 27 deletions(-)
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
index 6728520a21ca..0f3fadc1631c 100644
--- a/drivers/hwmon/lm90.c
+++ b/drivers/hwmon/lm90.c
@@ -80,6 +80,7 @@
* concern all supported chipsets, unless mentioned otherwise.
*/
+#include <linux/bits.h>
#include <linux/device.h>
#include <linux/err.h>
#include <linux/i2c.h>
@@ -182,36 +183,36 @@ enum chips { adm1032, adt7461, g781, lm86, lm90, lm99,
/*
* Device flags
*/
-#define LM90_FLAG_ADT7461_EXT (1 << 0) /* ADT7461 extended mode */
+#define LM90_FLAG_ADT7461_EXT BIT(0) /* ADT7461 extended mode */
/* Device features */
-#define LM90_HAVE_OFFSET (1 << 1) /* temperature offset register */
-#define LM90_HAVE_REM_LIMIT_EXT (1 << 3) /* extended remote limit */
-#define LM90_HAVE_EMERGENCY (1 << 4) /* 3rd upper (emergency) limit */
-#define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */
-#define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */
-#define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */
-#define LM90_HAVE_EXTENDED_TEMP (1 << 8) /* extended temperature support*/
-#define LM90_PAUSE_FOR_CONFIG (1 << 9) /* Pause conversion for config */
-#define LM90_HAVE_CRIT (1 << 10)/* Chip supports CRIT/OVERT register */
-#define LM90_HAVE_CRIT_ALRM_SWP (1 << 11)/* critical alarm bits swapped */
+#define LM90_HAVE_OFFSET BIT(1) /* temperature offset register */
+#define LM90_HAVE_REM_LIMIT_EXT BIT(3) /* extended remote limit */
+#define LM90_HAVE_EMERGENCY BIT(4) /* 3rd upper (emergency) limit */
+#define LM90_HAVE_EMERGENCY_ALARM BIT(5)/* emergency alarm */
+#define LM90_HAVE_TEMP3 BIT(6) /* 3rd temperature sensor */
+#define LM90_HAVE_BROKEN_ALERT BIT(7) /* Broken alert */
+#define LM90_HAVE_EXTENDED_TEMP BIT(8) /* extended temperature support */
+#define LM90_PAUSE_FOR_CONFIG BIT(9) /* Pause conversion for config */
+#define LM90_HAVE_CRIT BIT(10) /* Chip supports CRIT/OVERT register */
+#define LM90_HAVE_CRIT_ALRM_SWP BIT(11) /* critical alarm bits swapped */
/* LM90 status */
-#define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */
-#define LM90_STATUS_RTHRM (1 << 1) /* remote THERM limit tripped */
-#define LM90_STATUS_ROPEN (1 << 2) /* remote is an open circuit */
-#define LM90_STATUS_RLOW (1 << 3) /* remote low temp limit tripped */
-#define LM90_STATUS_RHIGH (1 << 4) /* remote high temp limit tripped */
-#define LM90_STATUS_LLOW (1 << 5) /* local low temp limit tripped */
-#define LM90_STATUS_LHIGH (1 << 6) /* local high temp limit tripped */
-#define LM90_STATUS_BUSY (1 << 7) /* conversion is ongoing */
-
-#define MAX6696_STATUS2_R2THRM (1 << 1) /* remote2 THERM limit tripped */
-#define MAX6696_STATUS2_R2OPEN (1 << 2) /* remote2 is an open circuit */
-#define MAX6696_STATUS2_R2LOW (1 << 3) /* remote2 low temp limit tripped */
-#define MAX6696_STATUS2_R2HIGH (1 << 4) /* remote2 high temp limit tripped */
-#define MAX6696_STATUS2_ROT2 (1 << 5) /* remote emergency limit tripped */
-#define MAX6696_STATUS2_R2OT2 (1 << 6) /* remote2 emergency limit tripped */
-#define MAX6696_STATUS2_LOT2 (1 << 7) /* local emergency limit tripped */
+#define LM90_STATUS_LTHRM BIT(0) /* local THERM limit tripped */
+#define LM90_STATUS_RTHRM BIT(1) /* remote THERM limit tripped */
+#define LM90_STATUS_ROPEN BIT(2) /* remote is an open circuit */
+#define LM90_STATUS_RLOW BIT(3) /* remote low temp limit tripped */
+#define LM90_STATUS_RHIGH BIT(4) /* remote high temp limit tripped */
+#define LM90_STATUS_LLOW BIT(5) /* local low temp limit tripped */
+#define LM90_STATUS_LHIGH BIT(6) /* local high temp limit tripped */
+#define LM90_STATUS_BUSY BIT(7) /* conversion is ongoing */
+
+#define MAX6696_STATUS2_R2THRM BIT(1) /* remote2 THERM limit tripped */
+#define MAX6696_STATUS2_R2OPEN BIT(2) /* remote2 is an open circuit */
+#define MAX6696_STATUS2_R2LOW BIT(3) /* remote2 low temp limit tripped */
+#define MAX6696_STATUS2_R2HIGH BIT(4) /* remote2 high temp limit tripped */
+#define MAX6696_STATUS2_ROT2 BIT(5) /* remote emergency limit tripped */
+#define MAX6696_STATUS2_R2OT2 BIT(6) /* remote2 emergency limit tripped */
+#define MAX6696_STATUS2_LOT2 BIT(7) /* local emergency limit tripped */
/*
* Driver data (common to all clients)
--
2.35.1
next prev parent reply other threads:[~2022-05-25 14:42 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-25 13:56 [PATCH 00/40] hwmon: (lm90) Various improvements to lm90 driver Guenter Roeck
2022-05-25 13:56 ` [PATCH 01/40] hwmon: (lm90) Generate sysfs and udev events for all alarms Guenter Roeck
2022-05-25 13:56 ` [PATCH 02/40] hwmon: (lm90) Rework alarm/status handling Guenter Roeck
2022-05-25 13:56 ` [PATCH 03/40] hwmon: (lm90) Reorder include files in alphabetical order Guenter Roeck
2022-05-25 13:56 ` [PATCH 04/40] hwmon: (lm90) Reorder chip enumeration to be " Guenter Roeck
2022-05-25 13:56 ` Guenter Roeck [this message]
2022-05-25 13:57 [PATCH 00/40] hwmon: (lm90) Various improvements to lm90 driver Guenter Roeck
2022-05-25 13:57 ` [PATCH 05/40] hwmon: (lm90) Use BIT macro Guenter Roeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220525135709.2899592-6-linux@roeck-us.net \
--to=linux@roeck-us.net \
--cc=jdelvare@suse.com \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=sst@poczta.fm \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.