From: Marian Ulbricht <ulbricht@innoroute.de>
To: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>,
"Krzysztof Kozlowski" <krzysztof.kozlowski+dt@linaro.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Tony Lindgren" <tony@atomide.com>,
linux-omap@vger.kernel.org
Subject: [PATCH v2 1/1] ARM: dts: add support for mws4 board
Date: Sun, 29 May 2022 22:37:24 +0200 [thread overview]
Message-ID: <20220529203724.GA43480@Denkbrett> (raw)
Mws4 is an ARM based nuclear probe hardware designed and used by
German government "Bundesamt fuer Strahlenschutz" to monitor
nuclear activity.
Signed-off-by: Marian Ulbricht <ulbricht@innoroute.de>
---
Changes in v2:
* cosmetics
Changes in v1:
* add dts
arch/arm/boot/dts/omap3-mws4.dts | 328 +++++++++++++++++++++++++++++++
1 file changed, 328 insertions(+)
create mode 100644 arch/arm/boot/dts/omap3-mws4.dts
diff --git a/arch/arm/boot/dts/omap3-mws4.dts b/arch/arm/boot/dts/omap3-mws4.dts
new file mode 100644
index 000000000000..680a8e4ee816
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-mws4.dts
@@ -0,0 +1,328 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Modified 2015 by Bernhard Gaetzschmann, Ultratronik from Beagleboard xM
+ *
+ * Modified 2022 Marian Ulbricht ulbricht@innoroute.de
+ *
+ */
+/dts-v1/;
+#include "omap36xx.dtsi"
+
+/ {
+ model = "Ultratronik BFS MWS4";
+ compatible = "ti,omap3-mws4", "ti,omap36xx", "ti,omap3";
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; // 256 MB
+ };
+
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ mmc1 = &mmc1;
+ };
+
+ netcard: AX88796BLI@ffdf0000 {
+ compatible = "ax88796_dt";
+ reg = <0xffdf0000 0x1000> ;
+
+};
+
+ watchdog_max: watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio4 21 1>; //117
+ hw_algo = "toggle";
+ always-running;
+ hw_margin_ms = <900>;
+ };
+
+ hsusb1_phy: hsusb1_phy {
+ status = "disabled";
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ status = "disabled";
+ };
+
+ /* fixed 19.2MHz oscillator */
+ hfclk_19m2: oscillator {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <19200000>;
+ };
+
+leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+ led_sm {
+ label = "led_sm";
+ gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* 101 */
+ default-state = "on";
+ };
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
+ linux,default-trigger = "cpu";
+ };
+
+ led2 {
+ label = "led2";
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* 103 */
+ linux,default-trigger = "mmc0";
+ };
+
+ led3 {
+ label = "led3";
+ gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
+ linux,default-trigger = "usb-host";
+ };
+
+ led_usb {
+ label = "led_usb";
+ gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* 110 */
+ default-state = "on";
+ };
+ };
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x1000000 /* CS0 space, 16MB */
+ 255 0 0x6e000000 0x02d4>; /* register space */
+
+ /* Chip select 0 */
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4 /* NAND I/O window, 4 bytes */
+ 255 0 0x02d4>; /* GPMC register space */
+ interrupts = <20>;
+ ti,nand-ecc-opt = "bch4";
+ nand-bus-width = <16>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <36>;
+ gpmc,cs-wr-off-ns = <36>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <24>;
+ gpmc,adv-wr-off-ns = <36>;
+ gpmc,oe-on-ns = <6>;
+ gpmc,oe-off-ns = <48>;
+ gpmc,we-on-ns = <6>;
+ gpmc,we-off-ns = <30>;
+ gpmc,rd-cycle-ns = <72>;
+ gpmc,wr-cycle-ns = <72>;
+ gpmc,access-ns = <54>;
+ gpmc,wr-access-ns = <30>;
+
+ partition@0 {
+ label = "X-Loader";
+ reg = <0 0x40000>;
+ };
+
+ partition@40000 {
+ label = "U-Boot";
+ reg = <0x40000 0x100000>;
+ };
+
+ partition@100000 {
+ label = "U-Boot Env";
+ reg = <0x100000 0x120000>;
+ };
+
+ partition@120000 {
+ label = "dt";
+ reg = <0x120000 0x140000>;
+ };
+
+ partition@140000 {
+ label = "Kernel";
+ reg = <0x140000 0xB40000>;
+ };
+
+ partition@B40000 {
+ label = "Filesystem";
+ reg = <0xB40000 0xf4c0000>;
+ };
+ };
+};
+
+&usbhshost {
+ status = "disabled";
+};
+
+&omap3_pmx_core {
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ >;
+ };
+
+ wd_pins: pinmux_wd_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x213e, PIN_OUTPUT | MUX_MODE4) // CONTROL_PADCONF_MCBSP2_CLKX 0x013E
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
+ OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
+ >;
+ };
+
+ hsusb0_pins: pinmux_hsusb0_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
+ OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
+ OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
+ OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
+ OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */
+ OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
+ OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
+ OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */
+ OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */
+ OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */
+ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */
+ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
+ >;
+ };
+
+ led_pins: pinmux_led_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x211a, PIN_OUTPUT | MUX_MODE4) /* gpio101*/
+ OMAP3_CORE1_IOPAD(0x211c, PIN_OUTPUT | MUX_MODE4) /* gpio102*/
+ OMAP3_CORE1_IOPAD(0x211e, PIN_OUTPUT | MUX_MODE4) /* gpio103 */
+ OMAP3_CORE1_IOPAD(0x2120, PIN_OUTPUT | MUX_MODE4) /* gpio103 */
+ >;
+ };
+
+ gpio_pins: pinmux_gpio_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE4) /* gpio105 spontanmeldung */
+ OMAP3_CORE1_IOPAD(0x212c, PIN_OUTPUT | MUX_MODE4) /* gpio110 usb2_en */
+ OMAP3_CORE1_IOPAD(0x218C, PIN_OUTPUT | MUX_MODE4) /* GPO0 */
+ OMAP3_CORE1_IOPAD(0x218E, PIN_OUTPUT | MUX_MODE4) /* GPO1 */
+ OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE4) /* GPO2 */
+ OMAP3_CORE1_IOPAD(0x2192, PIN_OUTPUT | MUX_MODE4) /* GPO3 */
+ OMAP3_CORE1_IOPAD(0x2194, PIN_OUTPUT | MUX_MODE4) /* GPO4 */
+ OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE4) /* GPO5 */
+ OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPO6 */
+ OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE4) /* IN1 */
+ OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE4) /* IN2 */
+ OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE4) /* IN3 */
+ OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE4) /* IN4 */
+ OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE4) /* IN5 */
+ OMAP3_CORE1_IOPAD(0x25F4, PIN_OUTPUT | MUX_MODE4) /* RES_RS232 */
+ OMAP3_CORE1_IOPAD(0x25F6, PIN_OUTPUT | MUX_MODE4) /* HUB_RESET */
+ >;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+
+ pinctrl-0 = <&i2c1_pins>;
+ clock-frequency = <100000>;
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ clocks = <&hfclk_19m2>;
+ clock-names = "fck";
+ twl_power: power {
+ compatible = "ti,twl4030-power";
+ ti,system-power-controller;
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ rtc8564: rtc8564@51 {
+ compatible = "epson,rtc8564";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vqmmc-supply = <&vsim>;
+ bus-width = <4>;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+};
+
+&usb_otg_hs {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb0_pins>;
+ num-eps = <16>;
+ ram-bits = <12>;
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <1>;
+ power = <500>;
+};
+
+&iva {
+ status = "disabled";
+};
+
+&sgx_module {
+ status = "disabled";
+};
+
+&vaux2 {
+ regulator-name = "usb_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
--
2.25.1
next reply other threads:[~2022-05-29 20:37 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-29 20:37 Marian Ulbricht [this message]
2022-05-30 7:30 ` [PATCH v2 1/1] ARM: dts: add support for mws4 board Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220529203724.GA43480@Denkbrett \
--to=ulbricht@innoroute.de \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-omap@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.