From: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> To: linus.walleij@linaro.org Cc: robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org, matthias.bgg@gmail.com, sean.wang@mediatek.com, linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org, nfraprado@collabora.com, AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Subject: [PATCH] dt-bindings: pinctrl: mt8195: Fix name for mediatek,rsel-resistance-in-si-unit Date: Thu, 30 Jun 2022 14:23:34 +0200 [thread overview] Message-ID: <20220630122334.216903-1-angelogioacchino.delregno@collabora.com> (raw) When this property was introduced, it contained underscores, but the actual code wants dashes. Change it from mediatek,rsel_resistance_in_si_unit to mediatek,rsel-resistance-in-si-unit. Fixes: 91e7edceda96 ("dt-bindings: pinctrl: mt8195: change pull up/down description") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> --- Note: No devicetree uses this property as of now. Even if any DT did, it wouldn't work, as the pinctrl code checks for 'mediatek,rsel-resistance-in-si-unit'. .../devicetree/bindings/pinctrl/pinctrl-mt8195.yaml | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml index 15989743afd2..b0fea44403e7 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml @@ -51,7 +51,7 @@ properties: description: The interrupt outputs to sysirq. maxItems: 1 - mediatek,rsel_resistance_in_si_unit: + mediatek,rsel-resistance-in-si-unit: type: boolean description: | Identifying i2c pins pull up/down type which is RSEL. It can support @@ -144,7 +144,7 @@ patternProperties: "MTK_PUPD_SET_R1R0_11" define in mt8195. For pull down type is RSEL, it can add RSEL define & resistance value(ohm) to set different resistance by identifying property - "mediatek,rsel_resistance_in_si_unit". + "mediatek,rsel-resistance-in-si-unit". It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" @@ -163,7 +163,7 @@ patternProperties: }; An example of using si unit resistance value(ohm): &pio { - mediatek,rsel_resistance_in_si_unit; + mediatek,rsel-resistance-in-si-unit; } pincontroller { i2c0_pin { @@ -192,7 +192,7 @@ patternProperties: "MTK_PUPD_SET_R1R0_11" define in mt8195. For pull up type is RSEL, it can add RSEL define & resistance value(ohm) to set different resistance by identifying property - "mediatek,rsel_resistance_in_si_unit". + "mediatek,rsel-resistance-in-si-unit". It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" @@ -211,7 +211,7 @@ patternProperties: }; An example of using si unit resistance value(ohm): &pio { - mediatek,rsel_resistance_in_si_unit; + mediatek,rsel-resistance-in-si-unit; } pincontroller { i2c0-pins { -- 2.35.1
WARNING: multiple messages have this Message-ID (diff)
From: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> To: linus.walleij@linaro.org Cc: robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org, matthias.bgg@gmail.com, sean.wang@mediatek.com, linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org, nfraprado@collabora.com, AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Subject: [PATCH] dt-bindings: pinctrl: mt8195: Fix name for mediatek,rsel-resistance-in-si-unit Date: Thu, 30 Jun 2022 14:23:34 +0200 [thread overview] Message-ID: <20220630122334.216903-1-angelogioacchino.delregno@collabora.com> (raw) When this property was introduced, it contained underscores, but the actual code wants dashes. Change it from mediatek,rsel_resistance_in_si_unit to mediatek,rsel-resistance-in-si-unit. Fixes: 91e7edceda96 ("dt-bindings: pinctrl: mt8195: change pull up/down description") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> --- Note: No devicetree uses this property as of now. Even if any DT did, it wouldn't work, as the pinctrl code checks for 'mediatek,rsel-resistance-in-si-unit'. .../devicetree/bindings/pinctrl/pinctrl-mt8195.yaml | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml index 15989743afd2..b0fea44403e7 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml @@ -51,7 +51,7 @@ properties: description: The interrupt outputs to sysirq. maxItems: 1 - mediatek,rsel_resistance_in_si_unit: + mediatek,rsel-resistance-in-si-unit: type: boolean description: | Identifying i2c pins pull up/down type which is RSEL. It can support @@ -144,7 +144,7 @@ patternProperties: "MTK_PUPD_SET_R1R0_11" define in mt8195. For pull down type is RSEL, it can add RSEL define & resistance value(ohm) to set different resistance by identifying property - "mediatek,rsel_resistance_in_si_unit". + "mediatek,rsel-resistance-in-si-unit". It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" @@ -163,7 +163,7 @@ patternProperties: }; An example of using si unit resistance value(ohm): &pio { - mediatek,rsel_resistance_in_si_unit; + mediatek,rsel-resistance-in-si-unit; } pincontroller { i2c0_pin { @@ -192,7 +192,7 @@ patternProperties: "MTK_PUPD_SET_R1R0_11" define in mt8195. For pull up type is RSEL, it can add RSEL define & resistance value(ohm) to set different resistance by identifying property - "mediatek,rsel_resistance_in_si_unit". + "mediatek,rsel-resistance-in-si-unit". It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" @@ -211,7 +211,7 @@ patternProperties: }; An example of using si unit resistance value(ohm): &pio { - mediatek,rsel_resistance_in_si_unit; + mediatek,rsel-resistance-in-si-unit; } pincontroller { i2c0-pins { -- 2.35.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2022-06-30 12:23 UTC|newest] Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top 2022-06-30 12:23 AngeloGioacchino Del Regno [this message] 2022-06-30 12:23 ` [PATCH] dt-bindings: pinctrl: mt8195: Fix name for mediatek,rsel-resistance-in-si-unit AngeloGioacchino Del Regno 2022-07-01 20:11 ` Rob Herring 2022-07-01 20:11 ` Rob Herring 2022-07-05 16:38 ` Nícolas F. R. A. Prado 2022-07-05 16:38 ` Nícolas F. R. A. Prado 2022-07-11 11:58 ` Linus Walleij 2022-07-11 11:58 ` Linus Walleij
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20220630122334.216903-1-angelogioacchino.delregno@collabora.com \ --to=angelogioacchino.delregno@collabora.com \ --cc=devicetree@vger.kernel.org \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linus.walleij@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-gpio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-mediatek@lists.infradead.org \ --cc=matthias.bgg@gmail.com \ --cc=nfraprado@collabora.com \ --cc=robh+dt@kernel.org \ --cc=sean.wang@mediatek.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.