All of lore.kernel.org
 help / color / mirror / Atom feed
From: Quan Nguyen <quan@os.amperecomputing.com>
To: Quan Nguyen <quan@os.amperecomputing.com>,
	openbmc@lists.ozlabs.org, Arnd Bergmann <arnd@arndb.de>,
	Olof Johansson <olof@lixom.net>,
	soc@kernel.org, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@aj.id.au>,
	linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-aspeed@lists.ozlabs.org,
	Open Source Submission <patches@amperecomputing.com>
Cc: Phong Vo <phong@os.amperecomputing.com>, thang@os.amperecomputing.com
Subject: [PATCH v3 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC
Date: Wed, 17 Aug 2022 14:15:39 +0700	[thread overview]
Message-ID: <20220817071539.176110-3-quan@os.amperecomputing.com> (raw)
In-Reply-To: <20220817071539.176110-1-quan@os.amperecomputing.com>

The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
hardware reference platform with AmpereOne(TM) processor.

Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
---
v3 :
  + Fix adc-i2c node to generic "adc" node                [Krzysztof]
  + Remove unused status property in adc node             [Krzysztof]
  + Remove trailing blank line at the end of file         [Krzysztof]
  + Remove the wrong comment on vga_memory nodes             [Andrew]
  + Remove gpio-keys                                         [Andrew]
  + Remove the line-name for bmc-debug-mode, eth-phy-rst-n,
    eth-phy-int-n, bmc-salt12-s0-ssif-n, fpga-program-b,
    bmc-uart-cts1, bmc-spi-fm-boot-abr-pd, emmc-rst-n gpios  [Andrew]
  + Update line-name for hs-csout-prochot, s1-spi-auth-fail-n  [Quan]
  + Add line-name [s0|s1]-heartbeat                            [Quan]

v2 :
  + Remove bootargs                                       [Krzysztof]
  + Fix gpio-keys nodes name to conform with device tree binding
  documents                                               [Krzysztof]
  + Fix some nodes to use generic name                    [Krzysztof]
  + Remove unnecessary blank line                         [Krzysztof]
  + Fix typo "LTC" to "LLC" in license info and corrected license
  info to GPL-2.0-only

 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 546 ++++++++++++++++++
 2 files changed, 547 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..5d8c6ce49af9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1576,6 +1576,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-ast2600-evb.dtb \
 	aspeed-bmc-amd-ethanolx.dtb \
 	aspeed-bmc-ampere-mtjade.dtb \
+	aspeed-bmc-ampere-mtmitchell.dtb \
 	aspeed-bmc-arm-stardragon4800-rep2.dtb \
 	aspeed-bmc-asrock-e3c246d4i.dtb \
 	aspeed-bmc-asrock-romed8hm3.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
new file mode 100644
index 000000000000..606cd4be245a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2022, Ampere Computing LLC
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt.Mitchell BMC";
+	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpioI5mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc14mux: adc14mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc15mux: adc15mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0mux 0>, <&adc0mux 1>,
+			<&adc1mux 0>, <&adc1mux 1>,
+			<&adc2mux 0>, <&adc2mux 1>,
+			<&adc3mux 0>, <&adc3mux 1>,
+			<&adc4mux 0>, <&adc4mux 1>,
+			<&adc5mux 0>, <&adc5mux 1>,
+			<&adc6mux 0>, <&adc6mux 1>,
+			<&adc7mux 0>, <&adc7mux 1>,
+			<&adc8mux 0>, <&adc8mux 1>,
+			<&adc9mux 0>, <&adc9mux 1>,
+			<&adc10mux 0>, <&adc10mux 1>,
+			<&adc11mux 0>, <&adc11mux 1>,
+			<&adc12mux 0>, <&adc12mux 1>,
+			<&adc13mux 0>, <&adc13mux 1>,
+			<&adc14mux 0>, <&adc14mux 1>,
+			<&adc15mux 0>, <&adc15mux 1>,
+			<&adc_i2c 0>, <&adc_i2c 1>,
+			<&adc_i2c 2>, <&adc_i2c 3>,
+			<&adc_i2c 4>, <&adc_i2c 5>,
+			<&adc_i2c 6>, <&adc_i2c 7>,
+			<&adc_i2c 8>, <&adc_i2c 9>,
+			<&adc_i2c 10>, <&adc_i2c 11>,
+			<&adc_i2c 12>, <&adc_i2c 13>,
+			<&adc_i2c 14>, <&adc_i2c 15>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	adc_i2c: adc@16 {
+		compatible = "lltc,ltc2497";
+		reg = <0x16>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			outlet_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu1_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			pcie_zone_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu0_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			pcie_zone_temp2: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			outlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			mb_inlet_temp1: temperature-sensor@7c {
+				compatible = "microchip,emc1413";
+				reg = <0x7c>;
+			};
+			mb_inlet_temp2: temperature-sensor@4c {
+				compatible = "microchip,emc1413";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@35 {
+		compatible = "ti,tmp175";
+		reg = <0x35>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
+	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","","",
+			"irq-n","","vrd-sel","spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","bmc-ncsi-txen","","",
+	/*E0-E7*/	"","","clk50m-bmc-ncsi","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
+			"cpu-bios-recover","s0-heartbeat","hs-csout-prochot",
+			"s0-vr-hot-n","s1-vr-hot-n",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","","","","","",
+	/*H0-H7*/	"","","wd-disable-n","power-chassis-good","","","","",
+	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
+			"s0-rtc-lock","","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","s1-heartbeat","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
+			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify",
+			"s1-ddr-save","spi-nor-access","sys-pgood","presence-cpu1",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
+			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
+			"s1-overtemp-n","s1-spi-auth-fail-n",
+	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
+	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","","","s0-soc-pgood","",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
-- 
2.35.1


WARNING: multiple messages have this Message-ID (diff)
From: Quan Nguyen <quan@os.amperecomputing.com>
To: Quan Nguyen <quan@os.amperecomputing.com>,
	openbmc@lists.ozlabs.org, Arnd Bergmann <arnd@arndb.de>,
	Olof Johansson <olof@lixom.net>,
	soc@kernel.org, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@aj.id.au>,
	linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-aspeed@lists.ozlabs.org,
	Open Source Submission <patches@amperecomputing.com>
Cc: Phong Vo <phong@os.amperecomputing.com>, thang@os.amperecomputing.com
Subject: [PATCH v3 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC
Date: Wed, 17 Aug 2022 14:15:39 +0700	[thread overview]
Message-ID: <20220817071539.176110-3-quan@os.amperecomputing.com> (raw)
In-Reply-To: <20220817071539.176110-1-quan@os.amperecomputing.com>

The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
hardware reference platform with AmpereOne(TM) processor.

Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
---
v3 :
  + Fix adc-i2c node to generic "adc" node                [Krzysztof]
  + Remove unused status property in adc node             [Krzysztof]
  + Remove trailing blank line at the end of file         [Krzysztof]
  + Remove the wrong comment on vga_memory nodes             [Andrew]
  + Remove gpio-keys                                         [Andrew]
  + Remove the line-name for bmc-debug-mode, eth-phy-rst-n,
    eth-phy-int-n, bmc-salt12-s0-ssif-n, fpga-program-b,
    bmc-uart-cts1, bmc-spi-fm-boot-abr-pd, emmc-rst-n gpios  [Andrew]
  + Update line-name for hs-csout-prochot, s1-spi-auth-fail-n  [Quan]
  + Add line-name [s0|s1]-heartbeat                            [Quan]

v2 :
  + Remove bootargs                                       [Krzysztof]
  + Fix gpio-keys nodes name to conform with device tree binding
  documents                                               [Krzysztof]
  + Fix some nodes to use generic name                    [Krzysztof]
  + Remove unnecessary blank line                         [Krzysztof]
  + Fix typo "LTC" to "LLC" in license info and corrected license
  info to GPL-2.0-only

 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 546 ++++++++++++++++++
 2 files changed, 547 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..5d8c6ce49af9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1576,6 +1576,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-ast2600-evb.dtb \
 	aspeed-bmc-amd-ethanolx.dtb \
 	aspeed-bmc-ampere-mtjade.dtb \
+	aspeed-bmc-ampere-mtmitchell.dtb \
 	aspeed-bmc-arm-stardragon4800-rep2.dtb \
 	aspeed-bmc-asrock-e3c246d4i.dtb \
 	aspeed-bmc-asrock-romed8hm3.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
new file mode 100644
index 000000000000..606cd4be245a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2022, Ampere Computing LLC
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt.Mitchell BMC";
+	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpioI5mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc14mux: adc14mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc15mux: adc15mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0mux 0>, <&adc0mux 1>,
+			<&adc1mux 0>, <&adc1mux 1>,
+			<&adc2mux 0>, <&adc2mux 1>,
+			<&adc3mux 0>, <&adc3mux 1>,
+			<&adc4mux 0>, <&adc4mux 1>,
+			<&adc5mux 0>, <&adc5mux 1>,
+			<&adc6mux 0>, <&adc6mux 1>,
+			<&adc7mux 0>, <&adc7mux 1>,
+			<&adc8mux 0>, <&adc8mux 1>,
+			<&adc9mux 0>, <&adc9mux 1>,
+			<&adc10mux 0>, <&adc10mux 1>,
+			<&adc11mux 0>, <&adc11mux 1>,
+			<&adc12mux 0>, <&adc12mux 1>,
+			<&adc13mux 0>, <&adc13mux 1>,
+			<&adc14mux 0>, <&adc14mux 1>,
+			<&adc15mux 0>, <&adc15mux 1>,
+			<&adc_i2c 0>, <&adc_i2c 1>,
+			<&adc_i2c 2>, <&adc_i2c 3>,
+			<&adc_i2c 4>, <&adc_i2c 5>,
+			<&adc_i2c 6>, <&adc_i2c 7>,
+			<&adc_i2c 8>, <&adc_i2c 9>,
+			<&adc_i2c 10>, <&adc_i2c 11>,
+			<&adc_i2c 12>, <&adc_i2c 13>,
+			<&adc_i2c 14>, <&adc_i2c 15>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	adc_i2c: adc@16 {
+		compatible = "lltc,ltc2497";
+		reg = <0x16>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			outlet_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu1_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			pcie_zone_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu0_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			pcie_zone_temp2: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			outlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			mb_inlet_temp1: temperature-sensor@7c {
+				compatible = "microchip,emc1413";
+				reg = <0x7c>;
+			};
+			mb_inlet_temp2: temperature-sensor@4c {
+				compatible = "microchip,emc1413";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@35 {
+		compatible = "ti,tmp175";
+		reg = <0x35>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
+	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","","",
+			"irq-n","","vrd-sel","spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","bmc-ncsi-txen","","",
+	/*E0-E7*/	"","","clk50m-bmc-ncsi","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
+			"cpu-bios-recover","s0-heartbeat","hs-csout-prochot",
+			"s0-vr-hot-n","s1-vr-hot-n",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","","","","","",
+	/*H0-H7*/	"","","wd-disable-n","power-chassis-good","","","","",
+	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
+			"s0-rtc-lock","","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","s1-heartbeat","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
+			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify",
+			"s1-ddr-save","spi-nor-access","sys-pgood","presence-cpu1",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
+			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
+			"s1-overtemp-n","s1-spi-auth-fail-n",
+	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
+	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","","","s0-soc-pgood","",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

WARNING: multiple messages have this Message-ID (diff)
From: Quan Nguyen <quan@os.amperecomputing.com>
To: Quan Nguyen <quan@os.amperecomputing.com>,
	openbmc@lists.ozlabs.org, Arnd Bergmann <arnd@arndb.de>,
	Olof Johansson <olof@lixom.net>,
	soc@kernel.org, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@aj.id.au>,
	linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-aspeed@lists.ozlabs.org,
	Open Source Submission <patches@amperecomputing.com>
Cc: thang@os.amperecomputing.com, Phong Vo <phong@os.amperecomputing.com>
Subject: [PATCH v3 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC
Date: Wed, 17 Aug 2022 14:15:39 +0700	[thread overview]
Message-ID: <20220817071539.176110-3-quan@os.amperecomputing.com> (raw)
In-Reply-To: <20220817071539.176110-1-quan@os.amperecomputing.com>

The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
hardware reference platform with AmpereOne(TM) processor.

Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
---
v3 :
  + Fix adc-i2c node to generic "adc" node                [Krzysztof]
  + Remove unused status property in adc node             [Krzysztof]
  + Remove trailing blank line at the end of file         [Krzysztof]
  + Remove the wrong comment on vga_memory nodes             [Andrew]
  + Remove gpio-keys                                         [Andrew]
  + Remove the line-name for bmc-debug-mode, eth-phy-rst-n,
    eth-phy-int-n, bmc-salt12-s0-ssif-n, fpga-program-b,
    bmc-uart-cts1, bmc-spi-fm-boot-abr-pd, emmc-rst-n gpios  [Andrew]
  + Update line-name for hs-csout-prochot, s1-spi-auth-fail-n  [Quan]
  + Add line-name [s0|s1]-heartbeat                            [Quan]

v2 :
  + Remove bootargs                                       [Krzysztof]
  + Fix gpio-keys nodes name to conform with device tree binding
  documents                                               [Krzysztof]
  + Fix some nodes to use generic name                    [Krzysztof]
  + Remove unnecessary blank line                         [Krzysztof]
  + Fix typo "LTC" to "LLC" in license info and corrected license
  info to GPL-2.0-only

 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 546 ++++++++++++++++++
 2 files changed, 547 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..5d8c6ce49af9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1576,6 +1576,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-ast2600-evb.dtb \
 	aspeed-bmc-amd-ethanolx.dtb \
 	aspeed-bmc-ampere-mtjade.dtb \
+	aspeed-bmc-ampere-mtmitchell.dtb \
 	aspeed-bmc-arm-stardragon4800-rep2.dtb \
 	aspeed-bmc-asrock-e3c246d4i.dtb \
 	aspeed-bmc-asrock-romed8hm3.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
new file mode 100644
index 000000000000..606cd4be245a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2022, Ampere Computing LLC
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt.Mitchell BMC";
+	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpioI5mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc14mux: adc14mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc15mux: adc15mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0mux 0>, <&adc0mux 1>,
+			<&adc1mux 0>, <&adc1mux 1>,
+			<&adc2mux 0>, <&adc2mux 1>,
+			<&adc3mux 0>, <&adc3mux 1>,
+			<&adc4mux 0>, <&adc4mux 1>,
+			<&adc5mux 0>, <&adc5mux 1>,
+			<&adc6mux 0>, <&adc6mux 1>,
+			<&adc7mux 0>, <&adc7mux 1>,
+			<&adc8mux 0>, <&adc8mux 1>,
+			<&adc9mux 0>, <&adc9mux 1>,
+			<&adc10mux 0>, <&adc10mux 1>,
+			<&adc11mux 0>, <&adc11mux 1>,
+			<&adc12mux 0>, <&adc12mux 1>,
+			<&adc13mux 0>, <&adc13mux 1>,
+			<&adc14mux 0>, <&adc14mux 1>,
+			<&adc15mux 0>, <&adc15mux 1>,
+			<&adc_i2c 0>, <&adc_i2c 1>,
+			<&adc_i2c 2>, <&adc_i2c 3>,
+			<&adc_i2c 4>, <&adc_i2c 5>,
+			<&adc_i2c 6>, <&adc_i2c 7>,
+			<&adc_i2c 8>, <&adc_i2c 9>,
+			<&adc_i2c 10>, <&adc_i2c 11>,
+			<&adc_i2c 12>, <&adc_i2c 13>,
+			<&adc_i2c 14>, <&adc_i2c 15>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	adc_i2c: adc@16 {
+		compatible = "lltc,ltc2497";
+		reg = <0x16>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			outlet_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu1_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			pcie_zone_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu0_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			pcie_zone_temp2: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			outlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			mb_inlet_temp1: temperature-sensor@7c {
+				compatible = "microchip,emc1413";
+				reg = <0x7c>;
+			};
+			mb_inlet_temp2: temperature-sensor@4c {
+				compatible = "microchip,emc1413";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@35 {
+		compatible = "ti,tmp175";
+		reg = <0x35>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
+	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","","",
+			"irq-n","","vrd-sel","spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","bmc-ncsi-txen","","",
+	/*E0-E7*/	"","","clk50m-bmc-ncsi","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
+			"cpu-bios-recover","s0-heartbeat","hs-csout-prochot",
+			"s0-vr-hot-n","s1-vr-hot-n",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","","","","","",
+	/*H0-H7*/	"","","wd-disable-n","power-chassis-good","","","","",
+	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
+			"s0-rtc-lock","","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","s1-heartbeat","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
+			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify",
+			"s1-ddr-save","spi-nor-access","sys-pgood","presence-cpu1",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
+			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
+			"s1-overtemp-n","s1-spi-auth-fail-n",
+	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
+	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","","","s0-soc-pgood","",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
-- 
2.35.1


  parent reply	other threads:[~2022-08-17  7:17 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-17  7:15 [PATCH v3 0/2] Add device tree for Ampere's Mt. Mitchell BMC Quan Nguyen
2022-08-17  7:15 ` Quan Nguyen
2022-08-17  7:15 ` Quan Nguyen
2022-08-17  7:15 ` [PATCH v3 1/2] dt-bindings: arm: aspeed: document Ampere Mt.Mitchell BMC compatibles Quan Nguyen
2022-08-17  7:15   ` Quan Nguyen
2022-08-17  7:15   ` Quan Nguyen
2022-08-17  7:46   ` Krzysztof Kozlowski
2022-08-17  7:46     ` Krzysztof Kozlowski
2022-08-17  7:15 ` Quan Nguyen [this message]
2022-08-17  7:15   ` [PATCH v3 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC Quan Nguyen
2022-08-17  7:15   ` Quan Nguyen
2022-08-18  7:33   ` Joel Stanley
2022-08-18  7:33     ` Joel Stanley
2022-08-18  7:33     ` Joel Stanley
2022-08-18 12:06     ` Arnd Bergmann
2022-08-18 12:06       ` Arnd Bergmann
2022-08-18 12:06       ` Arnd Bergmann
2022-08-23  8:27       ` Quan Nguyen
2022-08-23  8:27         ` Quan Nguyen
2022-08-23  8:27         ` Quan Nguyen
2022-08-25 12:35         ` Arnd Bergmann
2022-08-25 12:35           ` Arnd Bergmann
2022-08-25 12:35           ` Arnd Bergmann
2022-09-05  9:45           ` Quan Nguyen
2022-09-05  9:45             ` Quan Nguyen
2022-09-05  9:45             ` Quan Nguyen
2022-09-13  7:42             ` Quan Nguyen
2022-09-13  7:42               ` Quan Nguyen
2022-09-13  7:42               ` Quan Nguyen
2022-09-21  7:57               ` Quan Nguyen
2022-09-21  7:57                 ` Quan Nguyen
2022-09-21  7:57                 ` Quan Nguyen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220817071539.176110-3-quan@os.amperecomputing.com \
    --to=quan@os.amperecomputing.com \
    --cc=andrew@aj.id.au \
    --cc=arnd@arndb.de \
    --cc=devicetree@vger.kernel.org \
    --cc=joel@jms.id.au \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-aspeed@lists.ozlabs.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=olof@lixom.net \
    --cc=openbmc@lists.ozlabs.org \
    --cc=patches@amperecomputing.com \
    --cc=phong@os.amperecomputing.com \
    --cc=robh+dt@kernel.org \
    --cc=soc@kernel.org \
    --cc=thang@os.amperecomputing.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.