From: Vignesh Raghavendra <vigneshr@ti.com> To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>, Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Linus Walleij <linus.walleij@linaro.org> Cc: <linux-arm-kernel@lists.infradead.org>, <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>, <linux-gpio@vger.kernel.org>, Bryan Brattlof <bb@ti.com> Subject: [PATCH v2 5/5] arm64: dts: ti: Add support for AM62A7-SK Date: Thu, 1 Sep 2022 19:43:28 +0530 [thread overview] Message-ID: <20220901141328.899100-6-vigneshr@ti.com> (raw) In-Reply-To: <20220901141328.899100-1-vigneshr@ti.com> AM62A StarterKit (SK) board is a low cost, small form factor board designed for TI’s AM62A7 SoC. It supports the following interfaces: * 2 GB LPDDR4 RAM * x1 Gigabit Ethernet interface * x1 HDMI Port with audio * x1 Headphone Jack * x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port * x1 UHS-1 capable µSD card slot * M.2 SDIO Wifi + UART slot * 1Gb OSPI NAND flash * x4 UART through UART-USB bridge * XDS110 for onboard JTAG debug using USB * Temperature sensors, user push buttons and LEDs * 40-pin User Expansion Connector * 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO) * 20-pin header for Programmable Realtime Unit (PRU) IO pins * 40-pin CSI header Add basic support for AM62A7-SK. Schematics: https://www.ti.com/lit/zip/sprr459 Co-developed-by: Bryan Brattlof <bb@ti.com> Signed-off-by: Bryan Brattlof <bb@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- arch/arm64/boot/dts/ti/Makefile | 2 + arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 223 ++++++++++++++++++++++++ 2 files changed, 225 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index 02e5d80344d0..4555a5be2257 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -23,3 +23,5 @@ dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb + +dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts new file mode 100644 index 000000000000..576dbce80ad8 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts @@ -0,0 +1,223 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * AM62A SK: https://www.ti.com/lit/zip/sprr459 + * + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include <dt-bindings/leds/common.h> +#include <dt-bindings/gpio/gpio.h> +#include "k3-am62a7.dtsi" + +/ { + compatible = "ti,am62a7-sk", "ti,am62a7"; + model = "Texas Instruments AM62A7 SK"; + + aliases { + serial2 = &main_uart0; + mmc1 = &sdhci1; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + memory@80000000 { + device_type = "memory"; + /* 2G RAM */ + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_tfa_ddr: tfa@9e780000 { + reg = <0x00 0x9e780000 0x00 0x80000>; + alignment = <0x1000>; + no-map; + }; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ + alignment = <0x1000>; + no-map; + }; + + wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 { + compatible = "shared-dma-pool"; + reg = <0x00 0x9c900000 0x00 0x01e00000>; + no-map; + }; + }; + + vmain_pd: regulator-0 { + /* TPS25750 PD CONTROLLER OUTPUT */ + compatible = "regulator-fixed"; + regulator-name = "vmain_pd"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_5v0: regulator-1 { + /* Output of TPS63070 */ + compatible = "regulator-fixed"; + regulator-name = "vcc_5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vmain_pd>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_3v3_sys: regulator-2 { + /* output of LM5141-Q1 */ + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_sys"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vmain_pd>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_mmc1: regulator-3 { + /* TPS22918DBVR */ + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&exp1 3 GPIO_ACTIVE_HIGH>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&usr_led_pins_default>; + + led-0 { + label = "am62a-sk:green:heartbeat"; + gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + function = LED_FUNCTION_HEARTBEAT; + default-state = "off"; + }; + }; +}; + +&main_pmx0 { + main_uart0_pins_default: main-uart0-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */ + AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */ + >; + }; + + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */ + AM62AX_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */ + AM62AX_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */ + >; + }; + + main_i2c2_pins_default: main-i2c2-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */ + AM62AX_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */ + >; + }; + + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */ + AM62AX_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */ + AM62AX_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */ + AM62AX_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */ + AM62AX_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */ + AM62AX_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */ + AM62AX_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */ + >; + }; + + usr_led_pins_default: usr-led-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */ + >; + }; +}; + +&main_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; +}; + +&main_i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + clock-frequency = <400000>; + + exp1: gpio@22 { + compatible = "ti,tca6424"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST", + "BT_EN_SOC", "MMC1_SD_EN", + "VPP_EN", "EXP_PS_3V3_En", + "EXP_PS_5V0_En", "EXP_HAT_DETECT", + "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn", + "UART1_FET_BUF_EN", "BT_UART_WAKE_SOC", + "GPIO_HDMI_RSTn", "CSI_GPIO0", + "CSI_GPIO1", "WLAN_ALERTn", + "HDMI_INTn", "TEST_GPIO2", + "MCASP1_FET_EN", "MCASP1_BUF_BT_EN", + "MCASP1_FET_SEL", "UART1_FET_SEL", + "PD_I2C_IRQ", "IO_EXP_TEST_LED"; + }; +}; + +&sdhci1 { + /* SD/MMC */ + status = "okay"; + vmmc-supply = <&vdd_mmc1>; + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc1_pins_default>; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&main_gpio0 { + status = "okay"; +}; + +&main_gpio1 { + status = "okay"; +}; + +&main_gpio_intr { + status = "okay"; +}; + +&main_uart0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; +}; -- 2.37.2
WARNING: multiple messages have this Message-ID (diff)
From: Vignesh Raghavendra <vigneshr@ti.com> To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>, Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Linus Walleij <linus.walleij@linaro.org> Cc: <linux-arm-kernel@lists.infradead.org>, <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>, <linux-gpio@vger.kernel.org>, Bryan Brattlof <bb@ti.com> Subject: [PATCH v2 5/5] arm64: dts: ti: Add support for AM62A7-SK Date: Thu, 1 Sep 2022 19:43:28 +0530 [thread overview] Message-ID: <20220901141328.899100-6-vigneshr@ti.com> (raw) In-Reply-To: <20220901141328.899100-1-vigneshr@ti.com> AM62A StarterKit (SK) board is a low cost, small form factor board designed for TI’s AM62A7 SoC. It supports the following interfaces: * 2 GB LPDDR4 RAM * x1 Gigabit Ethernet interface * x1 HDMI Port with audio * x1 Headphone Jack * x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port * x1 UHS-1 capable µSD card slot * M.2 SDIO Wifi + UART slot * 1Gb OSPI NAND flash * x4 UART through UART-USB bridge * XDS110 for onboard JTAG debug using USB * Temperature sensors, user push buttons and LEDs * 40-pin User Expansion Connector * 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO) * 20-pin header for Programmable Realtime Unit (PRU) IO pins * 40-pin CSI header Add basic support for AM62A7-SK. Schematics: https://www.ti.com/lit/zip/sprr459 Co-developed-by: Bryan Brattlof <bb@ti.com> Signed-off-by: Bryan Brattlof <bb@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- arch/arm64/boot/dts/ti/Makefile | 2 + arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 223 ++++++++++++++++++++++++ 2 files changed, 225 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index 02e5d80344d0..4555a5be2257 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -23,3 +23,5 @@ dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb + +dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts new file mode 100644 index 000000000000..576dbce80ad8 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts @@ -0,0 +1,223 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * AM62A SK: https://www.ti.com/lit/zip/sprr459 + * + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include <dt-bindings/leds/common.h> +#include <dt-bindings/gpio/gpio.h> +#include "k3-am62a7.dtsi" + +/ { + compatible = "ti,am62a7-sk", "ti,am62a7"; + model = "Texas Instruments AM62A7 SK"; + + aliases { + serial2 = &main_uart0; + mmc1 = &sdhci1; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + memory@80000000 { + device_type = "memory"; + /* 2G RAM */ + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_tfa_ddr: tfa@9e780000 { + reg = <0x00 0x9e780000 0x00 0x80000>; + alignment = <0x1000>; + no-map; + }; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ + alignment = <0x1000>; + no-map; + }; + + wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 { + compatible = "shared-dma-pool"; + reg = <0x00 0x9c900000 0x00 0x01e00000>; + no-map; + }; + }; + + vmain_pd: regulator-0 { + /* TPS25750 PD CONTROLLER OUTPUT */ + compatible = "regulator-fixed"; + regulator-name = "vmain_pd"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_5v0: regulator-1 { + /* Output of TPS63070 */ + compatible = "regulator-fixed"; + regulator-name = "vcc_5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vmain_pd>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_3v3_sys: regulator-2 { + /* output of LM5141-Q1 */ + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_sys"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vmain_pd>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_mmc1: regulator-3 { + /* TPS22918DBVR */ + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&exp1 3 GPIO_ACTIVE_HIGH>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&usr_led_pins_default>; + + led-0 { + label = "am62a-sk:green:heartbeat"; + gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + function = LED_FUNCTION_HEARTBEAT; + default-state = "off"; + }; + }; +}; + +&main_pmx0 { + main_uart0_pins_default: main-uart0-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */ + AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */ + >; + }; + + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */ + AM62AX_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */ + AM62AX_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */ + >; + }; + + main_i2c2_pins_default: main-i2c2-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */ + AM62AX_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */ + >; + }; + + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */ + AM62AX_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */ + AM62AX_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */ + AM62AX_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */ + AM62AX_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */ + AM62AX_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */ + AM62AX_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */ + >; + }; + + usr_led_pins_default: usr-led-pins-default { + pinctrl-single,pins = < + AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */ + >; + }; +}; + +&main_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; +}; + +&main_i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + clock-frequency = <400000>; + + exp1: gpio@22 { + compatible = "ti,tca6424"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST", + "BT_EN_SOC", "MMC1_SD_EN", + "VPP_EN", "EXP_PS_3V3_En", + "EXP_PS_5V0_En", "EXP_HAT_DETECT", + "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn", + "UART1_FET_BUF_EN", "BT_UART_WAKE_SOC", + "GPIO_HDMI_RSTn", "CSI_GPIO0", + "CSI_GPIO1", "WLAN_ALERTn", + "HDMI_INTn", "TEST_GPIO2", + "MCASP1_FET_EN", "MCASP1_BUF_BT_EN", + "MCASP1_FET_SEL", "UART1_FET_SEL", + "PD_I2C_IRQ", "IO_EXP_TEST_LED"; + }; +}; + +&sdhci1 { + /* SD/MMC */ + status = "okay"; + vmmc-supply = <&vdd_mmc1>; + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc1_pins_default>; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&main_gpio0 { + status = "okay"; +}; + +&main_gpio1 { + status = "okay"; +}; + +&main_gpio_intr { + status = "okay"; +}; + +&main_uart0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; +}; -- 2.37.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-09-01 14:14 UTC|newest] Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top 2022-09-01 14:13 [PATCH v2 0/5] arm64: dts: ti: Add support for AM62A family of SoCs Vignesh Raghavendra 2022-09-01 14:13 ` Vignesh Raghavendra 2022-09-01 14:13 ` [PATCH v2 1/5] dt-bindings: arm: ti: Rearrange IOPAD macros alphabetically Vignesh Raghavendra 2022-09-01 14:13 ` Vignesh Raghavendra 2022-09-07 20:40 ` Rob Herring 2022-09-07 20:40 ` Rob Herring 2022-09-01 14:13 ` [PATCH v2 2/5] dt-bindings: arm: ti: Add bindings for AM62A7 SoC Vignesh Raghavendra 2022-09-01 14:13 ` Vignesh Raghavendra 2022-09-07 20:41 ` Rob Herring 2022-09-07 20:41 ` Rob Herring 2022-09-01 14:13 ` [PATCH v2 3/5] dt-bindings: pinctrl: k3: Introduce pinmux definitions for AM62A Vignesh Raghavendra 2022-09-01 14:13 ` Vignesh Raghavendra 2022-09-01 14:13 ` [PATCH v2 4/5] arm64: dts: ti: Introduce AM62A7 family of SoCs Vignesh Raghavendra 2022-09-01 14:13 ` Vignesh Raghavendra 2022-09-01 14:13 ` Vignesh Raghavendra [this message] 2022-09-01 14:13 ` [PATCH v2 5/5] arm64: dts: ti: Add support for AM62A7-SK Vignesh Raghavendra 2022-09-13 6:57 ` [PATCH v2 0/5] arm64: dts: ti: Add support for AM62A family of SoCs Devarsh Thakkar 2022-09-13 6:57 ` Devarsh Thakkar 2022-09-19 16:03 ` Vignesh Raghavendra 2022-09-19 16:03 ` Vignesh Raghavendra
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20220901141328.899100-6-vigneshr@ti.com \ --to=vigneshr@ti.com \ --cc=bb@ti.com \ --cc=devicetree@vger.kernel.org \ --cc=kristo@kernel.org \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linus.walleij@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-gpio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=nm@ti.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.