[PATCH 1/2] arm64: dts: qcom: sm8550: Add UFS host controller and phy nodes

[Abel Vesa <abel.vesa@linaro.org>]

Add UFS host controller and PHY nodes.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 76 ++++++++++++++++++++++++++++
 1 file changed, 76 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 07ba709ca35f..27ce382cb594 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -1372,6 +1372,82 @@ mmss_noc: interconnect@1780000 {
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		ufs_mem_phy: phy@1d80000 {
+			compatible = "qcom,sm8550-qmp-ufs-phy";
+			reg = <0x0 0x01d80000 0x0 0x200>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "ref", "qref";
+			clocks = <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+				 <&tcsr TCSR_UFS_CLKREF_EN>;
+
+			power-domains = <&gcc UFS_MEM_PHY_GDSC>;
+
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+			status = "disabled";
+
+			ufs_mem_phy_lanes: phy@1d80400 {
+				reg = <0x0 0x01d81000 0x0 0x134>,
+				      <0x0 0x01d81200 0x0 0x3d8>,
+				      <0x0 0x01d80400 0x0 0x258>,
+				      <0x0 0x01d81800 0x0 0x134>,
+				      <0x0 0x01d81a00 0x0 0x3d8>;
+				#phy-cells = <0>;
+			};
+		};
+
+		ufs_mem_hc: ufshc@1d84000 {
+			compatible = "qcom,sm8550-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0x0 0x01d84000 0x0 0x3000>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			iommus = <&apps_smmu 0x60 0x0>;
+
+			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
+
+			interconnect-names = "ufs-ddr", "cpu-ufs";
+			clock-names =
+				"core_clk",
+				"bus_aggr_clk",
+				"iface_clk",
+				"core_clk_unipro",
+				"ref_clk",
+				"tx_lane0_sync_clk",
+				"rx_lane0_sync_clk",
+				"rx_lane1_sync_clk";
+			clocks =
+				<&gcc GCC_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_UFS_PHY_AHB_CLK>,
+				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				<&rpmhcc RPMH_LN_BB_CLK3>,
+				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			freq-table-hz =
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<75000000 300000000>,
+				<100000000 403000000>,
+				<0 0>,
+				<0 0>,
+				<0 0>;
+			status = "disabled";
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0x0 0x01f40000 0x0 0x20000>;
-- 
2.34.1