[PATCH 1/2] phy: renesas: r8a779f0-eth-serdes: Add .power_on() into phy_ops

[Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>]

Add r8a779f0_eth_serdes_power_on() to initialize the hardware for
each channel from the step 9 or later on the datasheet. In other words,
the procedure from the step 1 to 8 is for all channel and it is needed
once only. So, the .init() in any channel instance is called, this
driver initializes the hardware from step 1 to 8. And then, .power_on()
is called, this driver initializes the hardware from step 9 or later.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
 drivers/phy/renesas/r8a779f0-ether-serdes.c | 57 +++++++++++----------
 1 file changed, 29 insertions(+), 28 deletions(-)

diff --git a/drivers/phy/renesas/r8a779f0-ether-serdes.c b/drivers/phy/renesas/r8a779f0-ether-serdes.c
index e7588a940d69..9f55a08e6da1 100644
--- a/drivers/phy/renesas/r8a779f0-ether-serdes.c
+++ b/drivers/phy/renesas/r8a779f0-ether-serdes.c
@@ -242,34 +242,7 @@ static int r8a779f0_eth_serdes_hw_init(struct r8a779f0_eth_serdes_channel *chann
 	if (ret)
 		return ret;
 
-	ret = r8a779f0_eth_serdes_reg_wait(&dd->channel[0], 0x0000, 0x380, BIT(15), 0);
-	if (ret)
-		return ret;
-
-	for (i = 0; i < R8A779F0_ETH_SERDES_NUM; i++) {
-		ret = r8a779f0_eth_serdes_chan_setting(&dd->channel[i]);
-		if (ret)
-			return ret;
-	}
-
-	for (i = 0; i < R8A779F0_ETH_SERDES_NUM; i++) {
-		ret = r8a779f0_eth_serdes_chan_speed(&dd->channel[i]);
-		if (ret)
-			return ret;
-	}
-
-	for (i = 0; i < R8A779F0_ETH_SERDES_NUM; i++)
-		r8a779f0_eth_serdes_write32(dd->channel[i].addr, 0x03c0, 0x380, 0x0000);
-	for (i = 0; i < R8A779F0_ETH_SERDES_NUM; i++)
-		r8a779f0_eth_serdes_write32(dd->channel[i].addr, 0x03d0, 0x380, 0x0000);
-
-	for (i = 0; i < R8A779F0_ETH_SERDES_NUM; i++) {
-		ret = r8a779f0_eth_serdes_monitor_linkup(&dd->channel[i]);
-		if (ret)
-			return ret;
-	}
-
-	return 0;
+	return r8a779f0_eth_serdes_reg_wait(&dd->channel[0], 0x0000, 0x380, BIT(15), 0);
 }
 
 static int r8a779f0_eth_serdes_init(struct phy *p)
@@ -289,6 +262,33 @@ static int r8a779f0_eth_serdes_init(struct phy *p)
 	return ret;
 }
 
+static int r8a779f0_eth_serdes_hw_init_late(struct r8a779f0_eth_serdes_channel
+*channel)
+{
+	int ret;
+
+	ret = r8a779f0_eth_serdes_chan_setting(channel);
+	if (ret)
+		return ret;
+
+	ret = r8a779f0_eth_serdes_chan_speed(channel);
+	if (ret)
+		return ret;
+
+	r8a779f0_eth_serdes_write32(channel->addr, 0x03c0, 0x380, 0x0000);
+
+	r8a779f0_eth_serdes_write32(channel->addr, 0x03d0, 0x380, 0x0000);
+
+	return r8a779f0_eth_serdes_monitor_linkup(channel);
+}
+
+static int r8a779f0_eth_serdes_power_on(struct phy *p)
+{
+	struct r8a779f0_eth_serdes_channel *channel = phy_get_drvdata(p);
+
+	return r8a779f0_eth_serdes_hw_init_late(channel);
+}
+
 static int r8a779f0_eth_serdes_set_mode(struct phy *p, enum phy_mode mode,
 					int submode)
 {
@@ -319,6 +319,7 @@ static int r8a779f0_eth_serdes_set_speed(struct phy *p, int speed)
 
 static const struct phy_ops r8a779f0_eth_serdes_ops = {
 	.init		= r8a779f0_eth_serdes_init,
+	.power_on	= r8a779f0_eth_serdes_power_on,
 	.set_mode	= r8a779f0_eth_serdes_set_mode,
 	.set_speed	= r8a779f0_eth_serdes_set_speed,
 };
-- 
2.25.1