From: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> To: <ath11k@lists.infradead.org> Cc: <linux-wireless@vger.kernel.org>, Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Subject: [PATCH] wifi: ath11k: fix ce memory mapping for ahb devices Date: Fri, 13 Jan 2023 12:02:09 +0530 [thread overview] Message-ID: <20230113063209.7256-1-quic_rajkbhag@quicinc.com> (raw) Currently ath11k_ahb module is not loaded successfully and the wifi interface is not created. Kernel trace is seen while loading the ath11k_ahb module. The issue is seen in all ath11k AHB devices except in IPQ5018. This happens because in ath11k_ahb_probe(), ab->mem_ce is initialized with the value of ab->mem. However, at this instant ab->mem is not yet set. Later, during write to a particular memory via ath11k_ahb_write32() this ab->mem_ce is used with particular offset. Since ab->mem_ce is not set properly this possibly leads to memory conflict to handle kernel paging request and the below trace is seen. [ 93.035047] Unable to handle kernel paging request at virtual address ffff800100a00000 [ 93.035083] Mem abort info: [ 93.041869] ESR = 0x0000000096000045 [ 93.044561] EC = 0x25: DABT (current EL), IL = 32 bits [ 93.048377] SET = 0, FnV = 0 [ 93.053840] EA = 0, S1PTW = 0 [ 93.056704] FSC = 0x05: level 1 translation fault [ 93.059745] Data abort info: [ 93.064603] ISV = 0, ISS = 0x00000045 [ 93.067729] CM = 0, WnR = 1 [ 93.071287] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000042219000 [ 93.074409] [ffff800100a00000] pgd=100000007ffff003, p4d=100000007ffff003, pud=0000000000000000 [ 93.081195] Internal error: Oops: 0000000096000045 [#1] PREEMPT SMP [ 93.089598] Modules linked in: ath11k_ahb ath11k_pci ath11k qmi_helpers [ 93.095851] CPU: 2 PID: 66 Comm: kworker/u8:3 Not tainted 6.1.0-rc8-wt-ath-658126-g58e4b9df840c-dirty #2 [ 93.102454] Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK14 (DT) [ 93.112171] Workqueue: ath11k_qmi_driver_event ath11k_qmi_driver_event_work [ath11k] [ 93.118856] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 93.126838] pc : ath11k_ahb_write32+0xc/0x18 [ath11k_ahb] [ 93.133520] lr : ath11k_hal_srng_setup+0x860/0x8f0 [ath11k] [ 93.139075] sp : ffff80000aaebb70 [ 93.144452] x29: ffff80000aaebb70 x28: 0000000000000020 x27: ffff80000aaebc50 [ 93.147934] x26: ffff000004923750 x25: ffff000004921200 x24: ffff000004928000 [ 93.155051] x23: 0000000000000020 x22: ffff000004930000 x21: ffff000004923200 [ 93.162170] x20: ffff000004920000 x19: 00000000eea00000 x18: ffff0000049200f0 [ 93.169288] x17: 0000000000000000 x16: 0000000000000000 x15: 000000000000025e [ 93.176405] x14: ffff000003c414f0 x13: 0000000000000000 x12: 0000000000000008 [ 93.183524] x11: ffff000003c41488 x10: 0000000000000040 x9 : 0000000000000000 [ 93.190641] x8 : ffff80000a9dd100 x7 : 0000000000000000 x6 : 000000000000003f [ 93.197759] x5 : ffff800100a00400 x4 : ffff8000031f4018 x3 : 0000000000000004 [ 93.204877] x2 : 0000000047b62000 x1 : ffff800100a00000 x0 : ffff800012000000 [ 93.211996] Call trace: [ 93.219104] ath11k_ahb_write32+0xc/0x18 [ath11k_ahb] [ 93.221366] ath11k_ce_init_ring+0x184/0x278 [ath11k] [ 93.226576] ath11k_ce_init_pipes+0x4c/0x1a0 [ath11k] [ 93.231610] ath11k_core_qmi_firmware_ready+0x3c/0x568 [ath11k] [ 93.236646] ath11k_qmi_driver_event_work+0x168/0x4f8 [ath11k] [ 93.242376] process_one_work+0x144/0x350 [ 93.248275] worker_thread+0x120/0x430 [ 93.252352] kthread+0xf4/0x110 [ 93.255997] ret_from_fork+0x10/0x20 [ 93.259043] Code: d503201f f94e1c00 8b214001 d50332bf (b9000022) [ 93.262863] ---[ end trace 0000000000000000 ]--- However, for the device IPQ5018 ath11k_hw_params .ce_remap is defined. This parameter is used to recalculate ab->mem_ce and hence, this issue is not seen in IPQ5018. Hence, fix this by initializing ab->mem_ce after ab->mem is set. ab->mem is set inside the ath11k_ahb_setup_resources() therefore initialize ab->mem_ce after ath11k_ahb_setup_resources(). Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Fixes: b42b3678c91f ("wifi: ath11k: remap ce register space for IPQ5018") Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> --- drivers/net/wireless/ath/ath11k/ahb.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/wireless/ath/ath11k/ahb.c b/drivers/net/wireless/ath/ath11k/ahb.c index 085e99633951..cd48eca494ed 100644 --- a/drivers/net/wireless/ath/ath11k/ahb.c +++ b/drivers/net/wireless/ath/ath11k/ahb.c @@ -1157,12 +1157,16 @@ static int ath11k_ahb_probe(struct platform_device *pdev) goto err_core_free; } - ab->mem_ce = ab->mem; - ret = ath11k_core_pre_init(ab); if (ret) goto err_core_free; + ret = ath11k_ahb_setup_resources(ab); + if (ret) + goto err_core_free; + + ab->mem_ce = ab->mem; + if (ab->hw_params.ce_remap) { const struct ce_remap *ce_remap = ab->hw_params.ce_remap; /* ce register space is moved out of wcss unlike ipq8074 or ipq6018 @@ -1177,10 +1181,6 @@ static int ath11k_ahb_probe(struct platform_device *pdev) } } - ret = ath11k_ahb_setup_resources(ab); - if (ret) - goto err_core_free; - ret = ath11k_ahb_fw_resources_init(ab); if (ret) goto err_core_free; base-commit: e51980bf88c65f6ad4916baf720ad1234de01791 -- 2.17.1 -- ath11k mailing list ath11k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath11k
WARNING: multiple messages have this Message-ID (diff)
From: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> To: <ath11k@lists.infradead.org> Cc: <linux-wireless@vger.kernel.org>, Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Subject: [PATCH] wifi: ath11k: fix ce memory mapping for ahb devices Date: Fri, 13 Jan 2023 12:02:09 +0530 [thread overview] Message-ID: <20230113063209.7256-1-quic_rajkbhag@quicinc.com> (raw) Currently ath11k_ahb module is not loaded successfully and the wifi interface is not created. Kernel trace is seen while loading the ath11k_ahb module. The issue is seen in all ath11k AHB devices except in IPQ5018. This happens because in ath11k_ahb_probe(), ab->mem_ce is initialized with the value of ab->mem. However, at this instant ab->mem is not yet set. Later, during write to a particular memory via ath11k_ahb_write32() this ab->mem_ce is used with particular offset. Since ab->mem_ce is not set properly this possibly leads to memory conflict to handle kernel paging request and the below trace is seen. [ 93.035047] Unable to handle kernel paging request at virtual address ffff800100a00000 [ 93.035083] Mem abort info: [ 93.041869] ESR = 0x0000000096000045 [ 93.044561] EC = 0x25: DABT (current EL), IL = 32 bits [ 93.048377] SET = 0, FnV = 0 [ 93.053840] EA = 0, S1PTW = 0 [ 93.056704] FSC = 0x05: level 1 translation fault [ 93.059745] Data abort info: [ 93.064603] ISV = 0, ISS = 0x00000045 [ 93.067729] CM = 0, WnR = 1 [ 93.071287] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000042219000 [ 93.074409] [ffff800100a00000] pgd=100000007ffff003, p4d=100000007ffff003, pud=0000000000000000 [ 93.081195] Internal error: Oops: 0000000096000045 [#1] PREEMPT SMP [ 93.089598] Modules linked in: ath11k_ahb ath11k_pci ath11k qmi_helpers [ 93.095851] CPU: 2 PID: 66 Comm: kworker/u8:3 Not tainted 6.1.0-rc8-wt-ath-658126-g58e4b9df840c-dirty #2 [ 93.102454] Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK14 (DT) [ 93.112171] Workqueue: ath11k_qmi_driver_event ath11k_qmi_driver_event_work [ath11k] [ 93.118856] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 93.126838] pc : ath11k_ahb_write32+0xc/0x18 [ath11k_ahb] [ 93.133520] lr : ath11k_hal_srng_setup+0x860/0x8f0 [ath11k] [ 93.139075] sp : ffff80000aaebb70 [ 93.144452] x29: ffff80000aaebb70 x28: 0000000000000020 x27: ffff80000aaebc50 [ 93.147934] x26: ffff000004923750 x25: ffff000004921200 x24: ffff000004928000 [ 93.155051] x23: 0000000000000020 x22: ffff000004930000 x21: ffff000004923200 [ 93.162170] x20: ffff000004920000 x19: 00000000eea00000 x18: ffff0000049200f0 [ 93.169288] x17: 0000000000000000 x16: 0000000000000000 x15: 000000000000025e [ 93.176405] x14: ffff000003c414f0 x13: 0000000000000000 x12: 0000000000000008 [ 93.183524] x11: ffff000003c41488 x10: 0000000000000040 x9 : 0000000000000000 [ 93.190641] x8 : ffff80000a9dd100 x7 : 0000000000000000 x6 : 000000000000003f [ 93.197759] x5 : ffff800100a00400 x4 : ffff8000031f4018 x3 : 0000000000000004 [ 93.204877] x2 : 0000000047b62000 x1 : ffff800100a00000 x0 : ffff800012000000 [ 93.211996] Call trace: [ 93.219104] ath11k_ahb_write32+0xc/0x18 [ath11k_ahb] [ 93.221366] ath11k_ce_init_ring+0x184/0x278 [ath11k] [ 93.226576] ath11k_ce_init_pipes+0x4c/0x1a0 [ath11k] [ 93.231610] ath11k_core_qmi_firmware_ready+0x3c/0x568 [ath11k] [ 93.236646] ath11k_qmi_driver_event_work+0x168/0x4f8 [ath11k] [ 93.242376] process_one_work+0x144/0x350 [ 93.248275] worker_thread+0x120/0x430 [ 93.252352] kthread+0xf4/0x110 [ 93.255997] ret_from_fork+0x10/0x20 [ 93.259043] Code: d503201f f94e1c00 8b214001 d50332bf (b9000022) [ 93.262863] ---[ end trace 0000000000000000 ]--- However, for the device IPQ5018 ath11k_hw_params .ce_remap is defined. This parameter is used to recalculate ab->mem_ce and hence, this issue is not seen in IPQ5018. Hence, fix this by initializing ab->mem_ce after ab->mem is set. ab->mem is set inside the ath11k_ahb_setup_resources() therefore initialize ab->mem_ce after ath11k_ahb_setup_resources(). Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Fixes: b42b3678c91f ("wifi: ath11k: remap ce register space for IPQ5018") Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> --- drivers/net/wireless/ath/ath11k/ahb.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/wireless/ath/ath11k/ahb.c b/drivers/net/wireless/ath/ath11k/ahb.c index 085e99633951..cd48eca494ed 100644 --- a/drivers/net/wireless/ath/ath11k/ahb.c +++ b/drivers/net/wireless/ath/ath11k/ahb.c @@ -1157,12 +1157,16 @@ static int ath11k_ahb_probe(struct platform_device *pdev) goto err_core_free; } - ab->mem_ce = ab->mem; - ret = ath11k_core_pre_init(ab); if (ret) goto err_core_free; + ret = ath11k_ahb_setup_resources(ab); + if (ret) + goto err_core_free; + + ab->mem_ce = ab->mem; + if (ab->hw_params.ce_remap) { const struct ce_remap *ce_remap = ab->hw_params.ce_remap; /* ce register space is moved out of wcss unlike ipq8074 or ipq6018 @@ -1177,10 +1181,6 @@ static int ath11k_ahb_probe(struct platform_device *pdev) } } - ret = ath11k_ahb_setup_resources(ab); - if (ret) - goto err_core_free; - ret = ath11k_ahb_fw_resources_init(ab); if (ret) goto err_core_free; base-commit: e51980bf88c65f6ad4916baf720ad1234de01791 -- 2.17.1
next reply other threads:[~2023-01-13 6:32 UTC|newest] Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top 2023-01-13 6:32 Raj Kumar Bhagat [this message] 2023-01-13 6:32 ` [PATCH] wifi: ath11k: fix ce memory mapping for ahb devices Raj Kumar Bhagat 2023-01-18 6:24 ` Kalle Valo 2023-01-18 6:24 ` Kalle Valo
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20230113063209.7256-1-quic_rajkbhag@quicinc.com \ --to=quic_rajkbhag@quicinc.com \ --cc=ath11k@lists.infradead.org \ --cc=linux-wireless@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.