All of lore.kernel.org
 help / color / mirror / Atom feed
From: Jagan Teki <jagan@amarulasolutions.com>
To: Heiko Stuebner <heiko@sntech.de>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, devicetree@vger.kernel.org,
	Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Subject: [PATCH 1/2] arm64: dts: rockchip: Enable Ethernet for Radxa CM3 IO
Date: Wed, 25 Jan 2023 21:40:22 +0530	[thread overview]
Message-ID: <20230125161023.12115-1-jagan@amarulasolutions.com> (raw)

From: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>

Add ethernet nodes for enabling gmac1 on the Radxa CM3 IO board.

Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
---
 .../boot/dts/rockchip/rk3566-radxa-cm3-io.dts | 93 +++++++++++++++++++
 1 file changed, 93 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
index 3e6578f27ec0..170af01371ff 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
@@ -21,6 +21,13 @@ chosen: chosen {
 		stdout-path = "serial2:1500000n8";
 	};
 
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
 	hdmi-con {
 		compatible = "hdmi-connector";
 		type = "a";
@@ -83,6 +90,29 @@ &combphy1 {
 	status = "okay";
 };
 
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&gmac1_clkin>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "input";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_rgmii_bus
+		     &gmac1m0_clkinout>;
+	snps,reset-gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x46>;
+	rx_delay = <0x2e>;
+	status = "okay";
+};
+
 &hdmi {
 	avdd-0v9-supply = <&vdda0v9_image>;
 	avdd-1v8-supply = <&vcca1v8_image>;
@@ -105,7 +135,70 @@ &hdmi_sound {
 	status = "okay";
 };
 
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible="ethernet-phy-ieee802.3-c22";
+		reg= <0x0>;
+	};
+};
+
 &pinctrl {
+	gmac1 {
+		gmac1m0_miim: gmac1m0-miim {
+			rockchip,pins =
+				/* gmac1_mdcm0 */
+				<3 RK_PC4 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_mdiom0 */
+				<3 RK_PC5 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rx_bus2: gmac1m0-rx-bus2 {
+			rockchip,pins =
+				/* gmac1_rxd0m0 */
+				<3 RK_PB1 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxd1m0 */
+				<3 RK_PB2 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxdvcrsm0 */
+				<3 RK_PB3 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_tx_bus2: gmac1m0-tx-bus2 {
+			rockchip,pins =
+				/* gmac1_txd0m0 */
+				<3 RK_PB5 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd1m0 */
+				<3 RK_PB6 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txenm0 */
+				<3 RK_PB7 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rgmii_clk: gmac1m0-rgmii-clk {
+			rockchip,pins =
+				/* gmac1_rxclkm0 */
+				<3 RK_PA7 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txclkm0 */
+				<3 RK_PA6 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rgmii_bus: gmac1m0-rgmii-bus {
+			rockchip,pins =
+				/* gmac1_rxd2m0 */
+				<3 RK_PA4 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxd3m0 */
+				<3 RK_PA5 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd2m0 */
+				<3 RK_PA2 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd3m0 */
+				<3 RK_PA3 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_clkinout: gmac1m0-clkinout {
+			rockchip,pins =
+				/* gmac1_mclkinoutm0 */
+				<3 RK_PC0 3 &pcfg_pull_none_drv_level_15>;
+		};
+	};
+
 	leds {
 		pi_nled_activity: pi-nled-activity {
 			rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
-- 
2.25.1


WARNING: multiple messages have this Message-ID (diff)
From: Jagan Teki <jagan@amarulasolutions.com>
To: Heiko Stuebner <heiko@sntech.de>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, devicetree@vger.kernel.org,
	Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Subject: [PATCH 1/2] arm64: dts: rockchip: Enable Ethernet for Radxa CM3 IO
Date: Wed, 25 Jan 2023 21:40:22 +0530	[thread overview]
Message-ID: <20230125161023.12115-1-jagan@amarulasolutions.com> (raw)

From: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>

Add ethernet nodes for enabling gmac1 on the Radxa CM3 IO board.

Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
---
 .../boot/dts/rockchip/rk3566-radxa-cm3-io.dts | 93 +++++++++++++++++++
 1 file changed, 93 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
index 3e6578f27ec0..170af01371ff 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
@@ -21,6 +21,13 @@ chosen: chosen {
 		stdout-path = "serial2:1500000n8";
 	};
 
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
 	hdmi-con {
 		compatible = "hdmi-connector";
 		type = "a";
@@ -83,6 +90,29 @@ &combphy1 {
 	status = "okay";
 };
 
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&gmac1_clkin>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "input";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_rgmii_bus
+		     &gmac1m0_clkinout>;
+	snps,reset-gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x46>;
+	rx_delay = <0x2e>;
+	status = "okay";
+};
+
 &hdmi {
 	avdd-0v9-supply = <&vdda0v9_image>;
 	avdd-1v8-supply = <&vcca1v8_image>;
@@ -105,7 +135,70 @@ &hdmi_sound {
 	status = "okay";
 };
 
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible="ethernet-phy-ieee802.3-c22";
+		reg= <0x0>;
+	};
+};
+
 &pinctrl {
+	gmac1 {
+		gmac1m0_miim: gmac1m0-miim {
+			rockchip,pins =
+				/* gmac1_mdcm0 */
+				<3 RK_PC4 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_mdiom0 */
+				<3 RK_PC5 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rx_bus2: gmac1m0-rx-bus2 {
+			rockchip,pins =
+				/* gmac1_rxd0m0 */
+				<3 RK_PB1 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxd1m0 */
+				<3 RK_PB2 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxdvcrsm0 */
+				<3 RK_PB3 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_tx_bus2: gmac1m0-tx-bus2 {
+			rockchip,pins =
+				/* gmac1_txd0m0 */
+				<3 RK_PB5 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd1m0 */
+				<3 RK_PB6 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txenm0 */
+				<3 RK_PB7 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rgmii_clk: gmac1m0-rgmii-clk {
+			rockchip,pins =
+				/* gmac1_rxclkm0 */
+				<3 RK_PA7 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txclkm0 */
+				<3 RK_PA6 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rgmii_bus: gmac1m0-rgmii-bus {
+			rockchip,pins =
+				/* gmac1_rxd2m0 */
+				<3 RK_PA4 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxd3m0 */
+				<3 RK_PA5 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd2m0 */
+				<3 RK_PA2 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd3m0 */
+				<3 RK_PA3 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_clkinout: gmac1m0-clkinout {
+			rockchip,pins =
+				/* gmac1_mclkinoutm0 */
+				<3 RK_PC0 3 &pcfg_pull_none_drv_level_15>;
+		};
+	};
+
 	leds {
 		pi_nled_activity: pi-nled-activity {
 			rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
-- 
2.25.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

WARNING: multiple messages have this Message-ID (diff)
From: Jagan Teki <jagan@amarulasolutions.com>
To: Heiko Stuebner <heiko@sntech.de>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, devicetree@vger.kernel.org,
	Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Subject: [PATCH 1/2] arm64: dts: rockchip: Enable Ethernet for Radxa CM3 IO
Date: Wed, 25 Jan 2023 21:40:22 +0530	[thread overview]
Message-ID: <20230125161023.12115-1-jagan@amarulasolutions.com> (raw)

From: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>

Add ethernet nodes for enabling gmac1 on the Radxa CM3 IO board.

Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
---
 .../boot/dts/rockchip/rk3566-radxa-cm3-io.dts | 93 +++++++++++++++++++
 1 file changed, 93 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
index 3e6578f27ec0..170af01371ff 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3-io.dts
@@ -21,6 +21,13 @@ chosen: chosen {
 		stdout-path = "serial2:1500000n8";
 	};
 
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
 	hdmi-con {
 		compatible = "hdmi-connector";
 		type = "a";
@@ -83,6 +90,29 @@ &combphy1 {
 	status = "okay";
 };
 
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&gmac1_clkin>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "input";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_rgmii_bus
+		     &gmac1m0_clkinout>;
+	snps,reset-gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x46>;
+	rx_delay = <0x2e>;
+	status = "okay";
+};
+
 &hdmi {
 	avdd-0v9-supply = <&vdda0v9_image>;
 	avdd-1v8-supply = <&vcca1v8_image>;
@@ -105,7 +135,70 @@ &hdmi_sound {
 	status = "okay";
 };
 
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible="ethernet-phy-ieee802.3-c22";
+		reg= <0x0>;
+	};
+};
+
 &pinctrl {
+	gmac1 {
+		gmac1m0_miim: gmac1m0-miim {
+			rockchip,pins =
+				/* gmac1_mdcm0 */
+				<3 RK_PC4 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_mdiom0 */
+				<3 RK_PC5 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rx_bus2: gmac1m0-rx-bus2 {
+			rockchip,pins =
+				/* gmac1_rxd0m0 */
+				<3 RK_PB1 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxd1m0 */
+				<3 RK_PB2 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxdvcrsm0 */
+				<3 RK_PB3 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_tx_bus2: gmac1m0-tx-bus2 {
+			rockchip,pins =
+				/* gmac1_txd0m0 */
+				<3 RK_PB5 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd1m0 */
+				<3 RK_PB6 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txenm0 */
+				<3 RK_PB7 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rgmii_clk: gmac1m0-rgmii-clk {
+			rockchip,pins =
+				/* gmac1_rxclkm0 */
+				<3 RK_PA7 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txclkm0 */
+				<3 RK_PA6 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_rgmii_bus: gmac1m0-rgmii-bus {
+			rockchip,pins =
+				/* gmac1_rxd2m0 */
+				<3 RK_PA4 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_rxd3m0 */
+				<3 RK_PA5 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd2m0 */
+				<3 RK_PA2 3 &pcfg_pull_none_drv_level_15>,
+				/* gmac1_txd3m0 */
+				<3 RK_PA3 3 &pcfg_pull_none_drv_level_15>;
+		};
+
+		gmac1m0_clkinout: gmac1m0-clkinout {
+			rockchip,pins =
+				/* gmac1_mclkinoutm0 */
+				<3 RK_PC0 3 &pcfg_pull_none_drv_level_15>;
+		};
+	};
+
 	leds {
 		pi_nled_activity: pi-nled-activity {
 			rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2023-01-25 16:10 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-25 16:10 Jagan Teki [this message]
2023-01-25 16:10 ` [PATCH 1/2] arm64: dts: rockchip: Enable Ethernet for Radxa CM3 IO Jagan Teki
2023-01-25 16:10 ` Jagan Teki
2023-01-25 16:10 ` [PATCH 2/2] arm64: dts: rockchip: rk3566: Enable WiFi, BT support for Radxa CM3 Jagan Teki
2023-01-25 16:10   ` Jagan Teki
2023-01-25 16:10   ` Jagan Teki
2023-01-29 13:39 ` [PATCH 1/2] arm64: dts: rockchip: Enable Ethernet for Radxa CM3 IO Heiko Stuebner
2023-01-29 13:39   ` Heiko Stuebner
2023-01-29 13:39   ` Heiko Stuebner

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230125161023.12115-1-jagan@amarulasolutions.com \
    --to=jagan@amarulasolutions.com \
    --cc=abbaraju.manojsai@amarulasolutions.com \
    --cc=devicetree@vger.kernel.org \
    --cc=heiko@sntech.de \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.