All of lore.kernel.org
 help / color / mirror / Atom feed
From: Samuel Holland <samuel@sholland.org>
To: Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@gmail.com>,
	linux-sunxi@lists.linux.dev
Cc: linux-riscv@lists.infradead.org, Heiko Stuebner <heiko@sntech.de>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Conor Dooley <conor@kernel.org>,
	Jisheng Zhang <jszhang@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	Andre Przywara <andre.przywara@arm.com>,
	Rob Herring <robh+dt@kernel.org>,
	linux-arm-kernel@lists.infradead.org,
	Samuel Holland <samuel@sholland.org>,
	Palmer Dabbelt <palmer@rivosinc.com>, Guo Ren <guoren@kernel.org>
Subject: [PATCH v5 08/11] riscv: dts: allwinner: Add MangoPi MQ Pro devicetree
Date: Wed, 25 Jan 2023 22:57:35 -0600	[thread overview]
Message-ID: <20230126045738.47903-9-samuel@sholland.org> (raw)
In-Reply-To: <20230126045738.47903-1-samuel@sholland.org>

The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
and an RTL8723DS-based WiFi/Bluetooth module.

The board also exposes GPIO Port E via a connector on the end of the
board, which can support either a camera or an RMII Ethernet PHY. The
additional regulators supply that connector.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---

(no changes since v3)

Changes in v3:
 - Drop mmc alias
 - Change LED_FUNCTION_BACKLIGHT to LED_FUNCTION_STATUS (the backlight
   regulator is disconnected by default, so this is a standalone LED)

Changes in v2:
 - Added LED (GPIO shared between onboard LED and backlight regulator)

 arch/riscv/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun20i-d1-mangopi-mq-pro.dts    | 142 ++++++++++++++++++
 2 files changed, 143 insertions(+)
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts

diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
index f1c70b9dc9bf..2ed586fafaea 100644
--- a/arch/riscv/boot/dts/allwinner/Makefile
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -3,5 +3,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-480p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-720p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-dock.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-mangopi-mq-pro.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
new file mode 100644
index 000000000000..f2e07043afb3
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "MangoPi MQ Pro";
+	compatible = "widora,mangopi-mq-pro", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &rtl8723ds;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
+		};
+	};
+
+	reg_avdd2v8: avdd2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_dvdd: dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 17 GPIO_ACTIVE_LOW>; /* PG17 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8723ds: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pe-supply = <&reg_avdd2v8>;
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
+		enable-gpios = <&pio 6 15 GPIO_ACTIVE_HIGH>; /* PG15 */
+		host-wake-gpios = <&pio 6 14 GPIO_ACTIVE_HIGH>; /* PG14 */
+	};
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
-- 
2.37.4


WARNING: multiple messages have this Message-ID (diff)
From: Samuel Holland <samuel@sholland.org>
To: Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@gmail.com>,
	linux-sunxi@lists.linux.dev
Cc: linux-riscv@lists.infradead.org, Heiko Stuebner <heiko@sntech.de>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Conor Dooley <conor@kernel.org>,
	Jisheng Zhang <jszhang@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	Andre Przywara <andre.przywara@arm.com>,
	Rob Herring <robh+dt@kernel.org>,
	linux-arm-kernel@lists.infradead.org,
	Samuel Holland <samuel@sholland.org>,
	Palmer Dabbelt <palmer@rivosinc.com>, Guo Ren <guoren@kernel.org>
Subject: [PATCH v5 08/11] riscv: dts: allwinner: Add MangoPi MQ Pro devicetree
Date: Wed, 25 Jan 2023 22:57:35 -0600	[thread overview]
Message-ID: <20230126045738.47903-9-samuel@sholland.org> (raw)
In-Reply-To: <20230126045738.47903-1-samuel@sholland.org>

The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
and an RTL8723DS-based WiFi/Bluetooth module.

The board also exposes GPIO Port E via a connector on the end of the
board, which can support either a camera or an RMII Ethernet PHY. The
additional regulators supply that connector.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---

(no changes since v3)

Changes in v3:
 - Drop mmc alias
 - Change LED_FUNCTION_BACKLIGHT to LED_FUNCTION_STATUS (the backlight
   regulator is disconnected by default, so this is a standalone LED)

Changes in v2:
 - Added LED (GPIO shared between onboard LED and backlight regulator)

 arch/riscv/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun20i-d1-mangopi-mq-pro.dts    | 142 ++++++++++++++++++
 2 files changed, 143 insertions(+)
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts

diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
index f1c70b9dc9bf..2ed586fafaea 100644
--- a/arch/riscv/boot/dts/allwinner/Makefile
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -3,5 +3,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-480p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-720p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-dock.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-mangopi-mq-pro.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
new file mode 100644
index 000000000000..f2e07043afb3
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "MangoPi MQ Pro";
+	compatible = "widora,mangopi-mq-pro", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &rtl8723ds;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
+		};
+	};
+
+	reg_avdd2v8: avdd2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_dvdd: dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 17 GPIO_ACTIVE_LOW>; /* PG17 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8723ds: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pe-supply = <&reg_avdd2v8>;
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
+		enable-gpios = <&pio 6 15 GPIO_ACTIVE_HIGH>; /* PG15 */
+		host-wake-gpios = <&pio 6 14 GPIO_ACTIVE_HIGH>; /* PG14 */
+	};
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
-- 
2.37.4


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

WARNING: multiple messages have this Message-ID (diff)
From: Samuel Holland <samuel@sholland.org>
To: Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@gmail.com>,
	linux-sunxi@lists.linux.dev
Cc: linux-riscv@lists.infradead.org, Heiko Stuebner <heiko@sntech.de>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Conor Dooley <conor@kernel.org>,
	Jisheng Zhang <jszhang@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	Andre Przywara <andre.przywara@arm.com>,
	Rob Herring <robh+dt@kernel.org>,
	linux-arm-kernel@lists.infradead.org,
	Samuel Holland <samuel@sholland.org>,
	Palmer Dabbelt <palmer@rivosinc.com>, Guo Ren <guoren@kernel.org>
Subject: [PATCH v5 08/11] riscv: dts: allwinner: Add MangoPi MQ Pro devicetree
Date: Wed, 25 Jan 2023 22:57:35 -0600	[thread overview]
Message-ID: <20230126045738.47903-9-samuel@sholland.org> (raw)
In-Reply-To: <20230126045738.47903-1-samuel@sholland.org>

The MangoPi MQ Pro is a tiny SBC with a layout compatible to the
Raspberry Pi Zero. It includes the Allwinner D1 SoC, 512M or 1G of DDR3,
and an RTL8723DS-based WiFi/Bluetooth module.

The board also exposes GPIO Port E via a connector on the end of the
board, which can support either a camera or an RMII Ethernet PHY. The
additional regulators supply that connector.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---

(no changes since v3)

Changes in v3:
 - Drop mmc alias
 - Change LED_FUNCTION_BACKLIGHT to LED_FUNCTION_STATUS (the backlight
   regulator is disconnected by default, so this is a standalone LED)

Changes in v2:
 - Added LED (GPIO shared between onboard LED and backlight regulator)

 arch/riscv/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun20i-d1-mangopi-mq-pro.dts    | 142 ++++++++++++++++++
 2 files changed, 143 insertions(+)
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts

diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
index f1c70b9dc9bf..2ed586fafaea 100644
--- a/arch/riscv/boot/dts/allwinner/Makefile
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -3,5 +3,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-480p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-86-panel-720p.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv-dock.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-lichee-rv.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-mangopi-mq-pro.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
new file mode 100644
index 000000000000..f2e07043afb3
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-mangopi-mq-pro.dts
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "MangoPi MQ Pro";
+	compatible = "widora,mangopi-mq-pro", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &rtl8723ds;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
+		};
+	};
+
+	reg_avdd2v8: avdd2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_dvdd: dvdd {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_vcc_3v3>;
+	};
+
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 17 GPIO_ACTIVE_LOW>; /* PG17 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8723ds: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pe-supply = <&reg_avdd2v8>;
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
+		enable-gpios = <&pio 6 15 GPIO_ACTIVE_HIGH>; /* PG15 */
+		host-wake-gpios = <&pio 6 14 GPIO_ACTIVE_HIGH>; /* PG14 */
+	};
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
-- 
2.37.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2023-01-26  4:57 UTC|newest]

Thread overview: 42+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-26  4:57 [PATCH v5 00/11] riscv: Allwinner D1/D1s platform support Samuel Holland
2023-01-26  4:57 ` Samuel Holland
2023-01-26  4:57 ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 01/11] MAINTAINERS: Match the sun20i family of Allwinner SoCs Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 02/11] dt-bindings: vendor-prefixes: Add Allwinner D1/D1s board vendors Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 03/11] dt-bindings: riscv: Add Allwinner D1/D1s board compatibles Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 04/11] riscv: dts: allwinner: Add the D1/D1s SoC devicetree Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 05/11] riscv: dts: allwinner: Add MangoPi MQ devicetree Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 06/11] riscv: dts: allwinner: Add Allwinner D1 Nezha devicetree Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 07/11] riscv: dts: allwinner: Add Sipeed Lichee RV devicetrees Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` Samuel Holland [this message]
2023-01-26  4:57   ` [PATCH v5 08/11] riscv: dts: allwinner: Add MangoPi MQ Pro devicetree Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 09/11] riscv: dts: allwinner: Add Dongshan Nezha STU devicetree Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 10/11] riscv: Add the Allwinner SoC family Kconfig option Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57 ` [PATCH v5 11/11] riscv: defconfig: Enable the Allwinner D1 platform and drivers Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  4:57   ` Samuel Holland
2023-01-26  8:00 ` [PATCH v5 00/11] riscv: Allwinner D1/D1s platform support Conor Dooley
2023-01-26  8:00   ` Conor Dooley
2023-01-26  8:00   ` Conor Dooley
2023-01-27 22:16 ` Jernej Škrabec
2023-01-27 22:16   ` Jernej Škrabec
2023-01-27 22:16   ` Jernej Škrabec

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230126045738.47903-9-samuel@sholland.org \
    --to=samuel@sholland.org \
    --cc=andre.przywara@arm.com \
    --cc=conor@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=guoren@kernel.org \
    --cc=heiko@sntech.de \
    --cc=jernej.skrabec@gmail.com \
    --cc=jszhang@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-riscv@lists.infradead.org \
    --cc=linux-sunxi@lists.linux.dev \
    --cc=palmer@dabbelt.com \
    --cc=palmer@rivosinc.com \
    --cc=robh+dt@kernel.org \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.