From: Adam Ford <aford173@gmail.com> To: linux-arm-kernel@lists.infradead.org Cc: aford@beaconembedded.com, Adam Ford <aford173@gmail.com>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>, Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix Kernel Team <kernel@pengutronix.de>, Fabio Estevam <festevam@gmail.com>, NXP Linux Team <linux-imx@nxp.com>, Catalin Marinas <catalin.marinas@arm.com>, Will Deacon <will@kernel.org>, devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS), linux-kernel@vger.kernel.org (open list) Subject: [PATCH V2 3/3] arm64: dts: imx8mn-beacon: Add support for OV5640 Camera Date: Sun, 7 May 2023 10:15:48 -0500 [thread overview] Message-ID: <20230507151549.1216019-3-aford173@gmail.com> (raw) In-Reply-To: <20230507151549.1216019-1-aford173@gmail.com> The baseboard has a very specific pinout for the TD Next 5640 camera which uses an OV5640 sensor. Enable it as part of the deveopment kit baseboard instead of an overlay. Enable the camera with the following media-ctl -l "'ov5640 1-0010':0 -> 'csis-32e30000.mipi-csi':0 [1]" media-ctl -v -V "'ov5640 1-0010':0 [fmt:UYVY8_1X16/640x480 field:none]" media-ctl -v -V "'crossbar':0 [fmt:UYVY8_1X16/640x480 field:none]" media-ctl -v -V "'mxc_isi.0':0 [fmt:UYVY8_1X16/640x480 field:none]" Signed-off-by: Adam Ford <aford173@gmail.com> --- V2: New to series, since Laurent asked me to add a board which supports the previous two commits. diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi index 9e82069c941f..6dce77a6114c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi @@ -43,6 +43,17 @@ reg_audio: regulator-audio { enable-active-high; }; + reg_camera: regulator-camera { + compatible = "regulator-fixed"; + regulator-name = "mipi_pwr"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&pca6416_1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + startup-delay-us = <100000>; + regulator-always-on; + }; + reg_usdhc2_vmmc: regulator-usdhc2 { compatible = "regulator-fixed"; regulator-name = "vsd_3v3"; @@ -96,6 +107,36 @@ eeprom@0 { }; }; +&i2c2 { + clock-frequency = <384000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + camera@10 { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x10>; + clocks = <&clk IMX8MN_CLK_CLKO1>; + clock-names = "xclk"; + assigned-clocks = <&clk IMX8MN_CLK_CLKO1>; + assigned-clock-parents = <&clk IMX8MN_CLK_24M>; + assigned-clock-rates = <24000000>; + AVDD-supply = <®_camera>; /* 2.8v */ + powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + + port { + /* MIPI CSI-2 bus endpoint */ + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi_in>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; +}; &i2c4 { clock-frequency = <400000>; pinctrl-names = "default"; @@ -145,11 +186,28 @@ wm8962: audio-codec@1a { }; }; +&isi { + status = "okay"; +}; + &easrc { fsl,asrc-rate = <48000>; status = "okay"; }; +&mipi_csi { + status = "okay"; + + ports { + port@0 { + mipi_csi_in: endpoint { + remote-endpoint = <&ov5640_to_mipi_csi2>; + data-lanes = <1 2>; + }; + }; + }; +}; + &sai3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai3>; @@ -226,6 +284,14 @@ MX8MN_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x41 >; }; + pinctrl_ov5640: ov5640grp { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 + MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 + MX8MN_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59 + >; + }; + pinctrl_pcal6414: pcal6414-gpiogrp { fsl,pins = < MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x19 -- 2.39.2
WARNING: multiple messages have this Message-ID (diff)
From: Adam Ford <aford173@gmail.com> To: linux-arm-kernel@lists.infradead.org Cc: aford@beaconembedded.com, Adam Ford <aford173@gmail.com>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>, Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix Kernel Team <kernel@pengutronix.de>, Fabio Estevam <festevam@gmail.com>, NXP Linux Team <linux-imx@nxp.com>, Catalin Marinas <catalin.marinas@arm.com>, Will Deacon <will@kernel.org>, devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS), linux-kernel@vger.kernel.org (open list) Subject: [PATCH V2 3/3] arm64: dts: imx8mn-beacon: Add support for OV5640 Camera Date: Sun, 7 May 2023 10:15:48 -0500 [thread overview] Message-ID: <20230507151549.1216019-3-aford173@gmail.com> (raw) In-Reply-To: <20230507151549.1216019-1-aford173@gmail.com> The baseboard has a very specific pinout for the TD Next 5640 camera which uses an OV5640 sensor. Enable it as part of the deveopment kit baseboard instead of an overlay. Enable the camera with the following media-ctl -l "'ov5640 1-0010':0 -> 'csis-32e30000.mipi-csi':0 [1]" media-ctl -v -V "'ov5640 1-0010':0 [fmt:UYVY8_1X16/640x480 field:none]" media-ctl -v -V "'crossbar':0 [fmt:UYVY8_1X16/640x480 field:none]" media-ctl -v -V "'mxc_isi.0':0 [fmt:UYVY8_1X16/640x480 field:none]" Signed-off-by: Adam Ford <aford173@gmail.com> --- V2: New to series, since Laurent asked me to add a board which supports the previous two commits. diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi index 9e82069c941f..6dce77a6114c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi @@ -43,6 +43,17 @@ reg_audio: regulator-audio { enable-active-high; }; + reg_camera: regulator-camera { + compatible = "regulator-fixed"; + regulator-name = "mipi_pwr"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&pca6416_1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + startup-delay-us = <100000>; + regulator-always-on; + }; + reg_usdhc2_vmmc: regulator-usdhc2 { compatible = "regulator-fixed"; regulator-name = "vsd_3v3"; @@ -96,6 +107,36 @@ eeprom@0 { }; }; +&i2c2 { + clock-frequency = <384000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + camera@10 { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x10>; + clocks = <&clk IMX8MN_CLK_CLKO1>; + clock-names = "xclk"; + assigned-clocks = <&clk IMX8MN_CLK_CLKO1>; + assigned-clock-parents = <&clk IMX8MN_CLK_24M>; + assigned-clock-rates = <24000000>; + AVDD-supply = <®_camera>; /* 2.8v */ + powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + + port { + /* MIPI CSI-2 bus endpoint */ + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&mipi_csi_in>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; +}; &i2c4 { clock-frequency = <400000>; pinctrl-names = "default"; @@ -145,11 +186,28 @@ wm8962: audio-codec@1a { }; }; +&isi { + status = "okay"; +}; + &easrc { fsl,asrc-rate = <48000>; status = "okay"; }; +&mipi_csi { + status = "okay"; + + ports { + port@0 { + mipi_csi_in: endpoint { + remote-endpoint = <&ov5640_to_mipi_csi2>; + data-lanes = <1 2>; + }; + }; + }; +}; + &sai3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai3>; @@ -226,6 +284,14 @@ MX8MN_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x41 >; }; + pinctrl_ov5640: ov5640grp { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 + MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 + MX8MN_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59 + >; + }; + pinctrl_pcal6414: pcal6414-gpiogrp { fsl,pins = < MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x19 -- 2.39.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2023-05-07 15:16 UTC|newest] Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top 2023-05-07 15:15 [PATCH V2 1/3] arm64: dts: imx8mn: Add CSI and ISI Nodes Adam Ford 2023-05-07 15:15 ` Adam Ford 2023-05-07 15:15 ` [PATCH V2 2/3] arm64: defconfig: Enable video capture drivers on imx8mm/imx8mn Adam Ford 2023-05-07 15:15 ` Adam Ford 2023-05-07 15:15 ` Adam Ford [this message] 2023-05-07 15:15 ` [PATCH V2 3/3] arm64: dts: imx8mn-beacon: Add support for OV5640 Camera Adam Ford 2023-05-15 1:26 ` [PATCH V2 1/3] arm64: dts: imx8mn: Add CSI and ISI Nodes Shawn Guo
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20230507151549.1216019-3-aford173@gmail.com \ --to=aford173@gmail.com \ --cc=aford@beaconembedded.com \ --cc=catalin.marinas@arm.com \ --cc=conor+dt@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=festevam@gmail.com \ --cc=kernel@pengutronix.de \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-imx@nxp.com \ --cc=linux-kernel@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=s.hauer@pengutronix.de \ --cc=shawnguo@kernel.org \ --cc=will@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.