[PATCH v3 12/15] arm64: dts: qcom: sc8180x: Add display and gpu nodes

[Vinod Koul <vkoul@kernel.org>]

This patch adds gpu, gmu, gpucc, dispcc and finally the mdss node with
dsi0/1, dp0/1 and edp subnodes as found in this SoC

Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sc8180x.dtsi | 658 ++++++++++++++++++++++++++
 1 file changed, 658 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
index c73fb25f5af0..e8613a00fcab 100644
--- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
@@ -4,7 +4,9 @@
  * Copyright (c) 2020-2023, Linaro Limited
  */
 
+#include <dt-bindings/clock/qcom,dispcc-sm8250.h>
 #include <dt-bindings/clock/qcom,gcc-sc8180x.h>
+#include <dt-bindings/clock/qcom,gpucc-sm8150.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/interconnect/qcom,osm-l3.h>
 #include <dt-bindings/interconnect/qcom,sc8180x.h>
@@ -2190,6 +2192,123 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		gpu: gpu@2c00000 {
+			compatible = "qcom,adreno-680.1", "qcom,adreno";
+			#stream-id-cells = <16>;
+
+			reg = <0 0x02c00000 0 0x40000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+			iommus = <&adreno_smmu 0 0xc01>;
+
+			operating-points-v2 = <&gpu_opp_table>;
+
+			interconnects = <&gem_noc MASTER_GRAPHICS_3D 0 &mc_virt SLAVE_EBI_CH0 0>;
+			interconnect-names = "gfx-mem";
+
+			qcom,gmu = <&gmu>;
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-514000000 {
+					opp-hz = /bits/ 64 <514000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+				};
+
+				opp-500000000 {
+					opp-hz = /bits/ 64 <500000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+				};
+
+				opp-461000000 {
+					opp-hz = /bits/ 64 <461000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+				};
+
+				opp-405000000 {
+					opp-hz = /bits/ 64 <405000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+				};
+
+				opp-315000000 {
+					opp-hz = /bits/ 64 <315000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+				};
+
+				opp-256000000 {
+					opp-hz = /bits/ 64 <256000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+				};
+
+				opp-177000000 {
+					opp-hz = /bits/ 64 <177000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+				};
+			};
+		};
+
+		gmu: gmu@2c6a000 {
+			compatible="qcom,adreno-gmu-680.1", "qcom,adreno-gmu";
+
+			reg = <0 0x02c6a000 0 0x30000>,
+			      <0 0x0b290000 0 0x10000>,
+			      <0 0x0b490000 0 0x10000>;
+			reg-names = "gmu",
+				    "gmu_pdc",
+				    "gmu_pdc_seq";
+
+			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hfi", "gmu";
+
+			clocks = <&gpucc GPU_CC_AHB_CLK>,
+				 <&gpucc GPU_CC_CX_GMU_CLK>,
+				 <&gpucc GPU_CC_CXO_CLK>,
+				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
+			clock-names = "ahb", "gmu", "cxo", "axi", "memnoc";
+
+			power-domains = <&gpucc GPU_CX_GDSC>,
+					<&gpucc GPU_GX_GDSC>;
+			power-domain-names = "cx", "gx";
+
+			iommus = <&adreno_smmu 5 0xc00>;
+
+			operating-points-v2 = <&gmu_opp_table>;
+
+			gmu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+				};
+
+				opp-500000000 {
+					opp-hz = /bits/ 64 <500000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+				};
+			};
+		};
+
+		gpucc: clock-controller@2c90000 {
+			compatible = "qcom,sc8180x-gpucc";
+			reg = <0 0x02c90000 0 0x9000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
+				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
+			clock-names = "bi_tcxo",
+				      "gcc_gpu_gpll0_clk_src",
+				      "gcc_gpu_gpll0_div_clk_src";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		adreno_smmu: iommu@2ca0000 {
 			compatible = "qcom,sc8180x-smmu-500", "arm,mmu-500";
 			reg = <0 0x02ca0000 0 0x10000>;
@@ -2539,6 +2658,545 @@ usb_sec_dwc3: usb@a800000 {
 			};
 		};
 
+		mdss: mdss@ae00000 {
+			compatible = "qcom,sc8180x-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&gcc GCC_DISP_SF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "nrt_bus",
+				      "core";
+
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interconnects = <&mmss_noc MASTER_MDP_PORT0 0 &mc_virt SLAVE_EBI_CH0 0>,
+					<&mmss_noc MASTER_MDP_PORT1 0 &mc_virt SLAVE_EBI_CH0 0>;
+			interconnect-names = "mdp0-mem", "mdp1-mem";
+
+			iommus = <&apps_smmu 0x800 0x420>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: mdp@ae01000 {
+				compatible = "qcom,sc8180x-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
+					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+						  <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <460000000>,
+						       <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+				power-domains = <&rpmhpd SC8180X_MMCX>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf0_out: endpoint {
+							remote-endpoint = <&dp0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+						dpu_intf2_out: endpoint {
+							remote-endpoint = <&dsi1_in>;
+						};
+					};
+
+					port@4 {
+						reg = <4>;
+						dpu_intf4_out: endpoint {
+							remote-endpoint = <&dp1_in>;
+						};
+					};
+
+					port@5 {
+						reg = <5>;
+						dpu_intf5_out: endpoint {
+							remote-endpoint = <&edp_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-345000000 {
+						opp-hz = /bits/ 64 <345000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-460000000 {
+						opp-hz = /bits/ 64 <460000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SC8180X_MMCX>;
+
+				phys = <&dsi0_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+
+				dsi_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+
+			dsi0_phy: dsi-phy@ae94400 {
+				compatible = "qcom,dsi-phy-7nm";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			dsi1: dsi@ae96000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SC8180X_MMCX>;
+
+				phys = <&dsi1_phy>;
+				phy-names = "dsi";
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi1_in: endpoint {
+							remote-endpoint = <&dpu_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi1_phy: dsi-phy@ae96400 {
+				compatible = "qcom,dsi-phy-7nm";
+				reg = <0 0x0ae96400 0 0x200>,
+				      <0 0x0ae96600 0 0x280>,
+				      <0 0x0ae96900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			mdss_dp0: displayport-controller@ae90000 {
+				compatible = "qcom,sc8180x-dp";
+				reg = <0 0xae90000 0 0x200>,
+				      <0 0xae90200 0 0x200>,
+				      <0 0xae90400 0 0x600>,
+				      <0 0xae90a00 0 0x400>;
+				interrupt-parent = <&mdss>;
+				interrupts = <12>;
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+				assigned-clock-parents = <&usb_prim_dpphy 0>, <&usb_prim_dpphy 1>;
+
+				phys = <&usb_prim_dpphy>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				operating-points-v2 = <&dp0_opp_table>;
+				power-domains = <&rpmhpd SC8180X_CX>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dp0_in: endpoint {
+							remote-endpoint = <&dpu_intf0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+					};
+				};
+
+				dp0_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dp1: displayport-controller@ae98000 {
+				compatible = "qcom,sc8180x-dp";
+				reg = <0 0xae98000 0 0x200>,
+				      <0 0xae98200 0 0x200>,
+				      <0 0xae98400 0 0x600>,
+				      <0 0xae98a00 0 0x400>;
+				interrupt-parent = <&mdss>;
+				interrupts = <13>;
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_AUX1_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK1_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK_SRC>;
+				assigned-clock-parents = <&usb_sec_dpphy 0>, <&usb_sec_dpphy 1>;
+
+				phys = <&usb_sec_dpphy>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				operating-points-v2 = <&dp0_opp_table>;
+				power-domains = <&rpmhpd SC8180X_CX>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dp1_in: endpoint {
+							remote-endpoint = <&dpu_intf4_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+					};
+				};
+
+				dp1_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_edp: displayport-controller@ae9a000 {
+				compatible = "qcom,sc8180x-edp";
+				reg = <0 0xae9a000 0 0x200>,
+				      <0 0xae9a200 0 0x200>,
+				      <0 0xae9a400 0 0x600>,
+				      <0 0xae9aa00 0 0x400>;
+				interrupt-parent = <&mdss>;
+				interrupts = <14>;
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					       "ctrl_link_iface",
+					      "stream_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>;
+				assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>;
+
+				phys = <&edp_phy>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				operating-points-v2 = <&edp_opp_table>;
+				power-domains = <&rpmhpd SC8180X_CX>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						edp_in: endpoint {
+							remote-endpoint = <&dpu_intf5_out>;
+						};
+					};
+				};
+
+				edp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+		};
+
+		edp_phy: phy@aec2a00 {
+			compatible = "qcom,sc8180x-edp-phy";
+			reg = <0 0x0aec2a00 0 0x1c0>,
+			      <0 0x0aec2200 0 0xa0>,
+			      <0 0x0aec2600 0 0xa0>,
+			      <0 0x0aec2000 0 0x19c>;
+
+			clocks = <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
+				 <&dispcc DISP_CC_MDSS_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+		};
+
+		dispcc: clock-controller@af00000 {
+			compatible = "qcom,sc8180x-dispcc";
+			reg = <0 0x0af00000 0 0x20000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&sleep_clk>,
+				 <&usb_prim_dpphy 0>,
+				 <&usb_prim_dpphy 1>,
+				 <&usb_sec_dpphy 0>,
+				 <&usb_sec_dpphy 1>,
+				 <&edp_phy 0>,
+				 <&edp_phy 1>;
+			clock-names = "bi_tcxo",
+				      "sleep_clk",
+				      "dp_phy_pll_link_clk",
+				      "dp_phy_pll_vco_div_clk",
+				      "dptx1_phy_pll_link_clk",
+				      "dptx1_phy_pll_vco_div_clk",
+				      "edp_phy_pll_link_clk",
+				      "edp_phy_pll_vco_div_clk";
+			power-domains = <&rpmhpd SC8180X_MMCX>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sc8180x-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>;
-- 
2.40.1