All of lore.kernel.org
 help / color / mirror / Atom feed
From: Vinod Koul <vkoul@kernel.org>
To: Bjorn Andersson <andersson@kernel.org>
Cc: linux-arm-msm@vger.kernel.org,
	Konrad Dybcio <konrad.dybcio@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	Vinod Koul <vkoul@kernel.org>
Subject: [PATCH v3 13/15] arm64: dts: qcom: sc8180x: Add pmics
Date: Tue, 30 May 2023 21:54:52 +0530	[thread overview]
Message-ID: <20230530162454.51708-14-vkoul@kernel.org> (raw)
In-Reply-To: <20230530162454.51708-1-vkoul@kernel.org>

SC8180X based platforms have PM8150, PM8150C, PMC8180 and SMB2351 PMICs,
so add these as well

Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi | 326 ++++++++++++++++++++
 1 file changed, 326 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
new file mode 100644
index 000000000000..8247af01c84a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2023, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+	thermal-zones {
+		pmc8180-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmc8180_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		pmc8180c-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmc8180c_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmc8180_0: pmic@0 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon: power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+
+				status = "disabled";
+			};
+		};
+
+		pmc8180_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmc8180_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8180_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pmc8180_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+		};
+
+		pmc8180_gpios: gpio@c000 {
+			compatible = "qcom,pmc8180-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pmc8180", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmic@2 {
+		compatible = "qcom,smb2351", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc@3100 {
+			compatible = "qcom,spmi-adc-rev2";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			vcoin@85 {
+				reg = <0x85>;
+				qcom,pre-scaling = <1 1>;
+				label = "vcoin2";
+			};
+		};
+	};
+
+	pmic@6 {
+		compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+		reg = <0x6 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmic@8 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmic@a {
+		compatible = "qcom,smb2351", "qcom,spmi-pmic";
+		reg = <0xa SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc@3100 {
+			compatible = "qcom,spmi-adc-rev2";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			vcoin@85 {
+				reg = <0x85>;
+				qcom,pre-scaling = <1 1>;
+				label = "vcoin";
+			};
+		};
+	};
+
+	pmic@4 {
+		compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+
+			status = "disabled";
+		};
+
+		pmc8180c_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8180c_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pmc8180c_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pmc8180c_gpios: gpio@c000 {
+			compatible = "qcom,pmc8180c-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@5 {
+		compatible = "qcom,pmc8180c", "qcom,spmi-pmic";
+		reg = <0x5 SPMI_USID>;
+
+		pmc8180c_lpg: lpg {
+			compatible = "qcom,pmc8180c-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+	};
+};
-- 
2.40.1


  parent reply	other threads:[~2023-05-30 16:27 UTC|newest]

Thread overview: 33+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-05-30 16:24 [PATCH v3 00/15] Introduce the SC8180x devices Vinod Koul
2023-05-30 16:24 ` [PATCH v3 01/15] dt-bindings: PCI: qcom: Fix sc8180x clocks and interrupts Vinod Koul
2023-05-31  8:19   ` Krzysztof Kozlowski
2023-06-01  7:21     ` Vinod Koul
2023-06-01  7:25       ` Krzysztof Kozlowski
2023-06-01  7:26   ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 02/15] dt-bindings: usb: qcom,dwc3: Add SC8180x binding Vinod Koul
2023-05-31  8:19   ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 03/15] dt-bindings: interconnect: split SC8180x to own schema Vinod Koul
2023-05-31  8:22   ` Krzysztof Kozlowski
2023-06-01  7:23     ` Vinod Koul
2023-06-01  7:26       ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 04/15] scsi: ufs: dt-bindings: Add SC8180x binding Vinod Koul
2023-05-31  8:24   ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 05/15] dt-bindings: qcom,pdc: Add SC8180x compatible Vinod Koul
2023-05-31  8:24   ` Krzysztof Kozlowski
2023-05-30 16:24 ` [PATCH v3 06/15] arm64: dts: qcom: Introduce the SC8180x platform Vinod Koul
2023-05-30 16:24 ` [PATCH v3 07/15] arm64: dts: qcom: sc8180x: Add interconnects and lmh Vinod Koul
2023-05-31  8:26   ` Krzysztof Kozlowski
2023-06-01  7:17     ` Vinod Koul
2023-06-01 13:27       ` Bjorn Andersson
2023-06-01 15:27         ` Krzysztof Kozlowski
2023-06-10 16:24           ` Bjorn Andersson
2023-05-30 16:24 ` [PATCH v3 08/15] arm64: dts: qcom: sc8180x: Add thermal zones Vinod Koul
2023-05-30 16:24 ` [PATCH v3 09/15] arm64: dts: qcom: sc8180x: Add QUPs Vinod Koul
2023-05-30 16:24 ` [PATCH v3 10/15] arm64: dts: qcom: sc8180x: Add PCIe instances Vinod Koul
2023-05-30 16:24 ` [PATCH v3 11/15] arm64: dts: qcom: sc8180x: Add remoteprocs, wifi and usb nodes Vinod Koul
2023-05-30 16:24 ` [PATCH v3 12/15] arm64: dts: qcom: sc8180x: Add display and gpu nodes Vinod Koul
2023-05-30 16:24 ` Vinod Koul [this message]
2023-06-07 19:31   ` [PATCH v3 13/15] arm64: dts: qcom: sc8180x: Add pmics Rob Herring
2023-05-30 16:24 ` [PATCH v3 14/15] arm64: dts: qcom: sc8180x: Introduce Primus Vinod Koul
2023-05-30 16:24 ` [PATCH v3 15/15] arm64: dts: qcom: sc8180x: Introduce Lenovo Flex 5G Vinod Koul
2023-05-30 17:22 ` (subset) [PATCH v3 00/15] Introduce the SC8180x devices Bjorn Andersson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230530162454.51708-14-vkoul@kernel.org \
    --to=vkoul@kernel.org \
    --cc=andersson@kernel.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=konrad.dybcio@linaro.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.