All of lore.kernel.org
 help / color / mirror / Atom feed
From: Apurva Nandan <a-nandan@ti.com>
To: Apurva Nandan <a-nandan@ti.com>, Nishanth Menon <nm@ti.com>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	Udit Kumar <u-kumar1@ti.com>, Hari Nagalla <hnagalla@ti.com>,
	Dasnavis Sabiya <sabiya.d@mistralsolutions.com>
Subject: [PATCH v2 4/4] arm64: dts: ti: k3-am69-sk: Add bootph-pre-ram property for SPL nodes
Date: Tue, 8 Aug 2023 00:26:45 +0530	[thread overview]
Message-ID: <20230807185645.128751-5-a-nandan@ti.com> (raw)
In-Reply-To: <20230807185645.128751-1-a-nandan@ti.com>

Add bootph-pre-ram property for all the nodes used in SPL stage,
for syncing it later to u-boot k3-am69 dts.

Signed-off-by: Apurva Nandan <a-nandan@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index d282c2c633c1..cbe88a26b283 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -110,7 +110,9 @@ vdd_sd_dv: regulator-tlv71033 {
 };
 
 &main_pmx0 {
+	bootph-pre-ram;
 	main_uart8_pins_default: main-uart8-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
 			J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
@@ -125,6 +127,7 @@ J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
 	};
 
 	main_mmc1_pins_default: main-mmc1-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
 			J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
@@ -164,7 +167,9 @@ J784S4_IOPAD(0x004, PIN_INPUT, 7) /* (AG36) MCAN12_TX.GPIO0_1 */
 };
 
 &wkup_pmx2 {
+	bootph-pre-ram;
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */
 			J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */
@@ -174,6 +179,7 @@ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */
 	};
 
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
 			J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
@@ -181,6 +187,7 @@ J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
 	};
 
 	mcu_uart0_pins_default: mcu-uart0-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */
 			J784S4_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (J37) WKUP_GPIO0_12.MCU_UART0_TXD */
@@ -242,6 +249,7 @@ J784S4_WKUP_IOPAD(0x0, PIN_INPUT, 7) /* (M33) WKUP_GPIO0_49 */
 };
 
 &wkup_uart0 {
+	bootph-pre-ram;
 	/* Firmware usage */
 	status = "reserved";
 	pinctrl-names = "default";
@@ -249,6 +257,7 @@ &wkup_uart0 {
 };
 
 &wkup_i2c0 {
+	bootph-pre-ram;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&wkup_i2c0_pins_default>;
@@ -268,6 +277,7 @@ &wkup_gpio0 {
 };
 
 &mcu_uart0 {
+	bootph-pre-ram;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_uart0_pins_default>;
@@ -281,6 +291,7 @@ &mcu_i2c0 {
 };
 
 &main_uart8 {
+	bootph-pre-ram;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart8_pins_default>;
@@ -307,6 +318,7 @@ exp1: gpio@21 {
 };
 
 &main_sdhci0 {
+	bootph-pre-ram;
 	/* eMMC */
 	status = "okay";
 	non-removable;
@@ -315,6 +327,7 @@ &main_sdhci0 {
 };
 
 &main_sdhci1 {
+	bootph-pre-ram;
 	/* SD card */
 	status = "okay";
 	pinctrl-0 = <&main_mmc1_pins_default>;
-- 
2.34.1


WARNING: multiple messages have this Message-ID (diff)
From: Apurva Nandan <a-nandan@ti.com>
To: Apurva Nandan <a-nandan@ti.com>, Nishanth Menon <nm@ti.com>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	Udit Kumar <u-kumar1@ti.com>, Hari Nagalla <hnagalla@ti.com>,
	Dasnavis Sabiya <sabiya.d@mistralsolutions.com>
Subject: [PATCH v2 4/4] arm64: dts: ti: k3-am69-sk: Add bootph-pre-ram property for SPL nodes
Date: Tue, 8 Aug 2023 00:26:45 +0530	[thread overview]
Message-ID: <20230807185645.128751-5-a-nandan@ti.com> (raw)
In-Reply-To: <20230807185645.128751-1-a-nandan@ti.com>

Add bootph-pre-ram property for all the nodes used in SPL stage,
for syncing it later to u-boot k3-am69 dts.

Signed-off-by: Apurva Nandan <a-nandan@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index d282c2c633c1..cbe88a26b283 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -110,7 +110,9 @@ vdd_sd_dv: regulator-tlv71033 {
 };
 
 &main_pmx0 {
+	bootph-pre-ram;
 	main_uart8_pins_default: main-uart8-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
 			J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
@@ -125,6 +127,7 @@ J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
 	};
 
 	main_mmc1_pins_default: main-mmc1-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
 			J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
@@ -164,7 +167,9 @@ J784S4_IOPAD(0x004, PIN_INPUT, 7) /* (AG36) MCAN12_TX.GPIO0_1 */
 };
 
 &wkup_pmx2 {
+	bootph-pre-ram;
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */
 			J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */
@@ -174,6 +179,7 @@ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */
 	};
 
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
 			J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
@@ -181,6 +187,7 @@ J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
 	};
 
 	mcu_uart0_pins_default: mcu-uart0-default-pins {
+		bootph-pre-ram;
 		pinctrl-single,pins = <
 			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */
 			J784S4_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (J37) WKUP_GPIO0_12.MCU_UART0_TXD */
@@ -242,6 +249,7 @@ J784S4_WKUP_IOPAD(0x0, PIN_INPUT, 7) /* (M33) WKUP_GPIO0_49 */
 };
 
 &wkup_uart0 {
+	bootph-pre-ram;
 	/* Firmware usage */
 	status = "reserved";
 	pinctrl-names = "default";
@@ -249,6 +257,7 @@ &wkup_uart0 {
 };
 
 &wkup_i2c0 {
+	bootph-pre-ram;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&wkup_i2c0_pins_default>;
@@ -268,6 +277,7 @@ &wkup_gpio0 {
 };
 
 &mcu_uart0 {
+	bootph-pre-ram;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_uart0_pins_default>;
@@ -281,6 +291,7 @@ &mcu_i2c0 {
 };
 
 &main_uart8 {
+	bootph-pre-ram;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart8_pins_default>;
@@ -307,6 +318,7 @@ exp1: gpio@21 {
 };
 
 &main_sdhci0 {
+	bootph-pre-ram;
 	/* eMMC */
 	status = "okay";
 	non-removable;
@@ -315,6 +327,7 @@ &main_sdhci0 {
 };
 
 &main_sdhci1 {
+	bootph-pre-ram;
 	/* SD card */
 	status = "okay";
 	pinctrl-0 = <&main_mmc1_pins_default>;
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2023-08-07 18:57 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-08-07 18:56 [PATCH v2 0/4] arm64: dts: ti: k3-j784s4: Add bootph-pre-ram property for SPL nodes Apurva Nandan
2023-08-07 18:56 ` Apurva Nandan
2023-08-07 18:56 ` [PATCH v2 1/4] arm64: dts: ti: k3-j784s4-main: " Apurva Nandan
2023-08-07 18:56   ` Apurva Nandan
2023-08-07 19:07   ` Nishanth Menon
2023-08-07 19:07     ` Nishanth Menon
2023-08-08 18:32     ` Apurva Nandan
2023-08-08 18:32       ` Apurva Nandan
2023-08-07 18:56 ` [PATCH v2 2/4] arm64: dts: ti: k3-j784s4-mcu-wakeup: " Apurva Nandan
2023-08-07 18:56   ` Apurva Nandan
2023-08-07 18:56 ` [PATCH v2 3/4] arm64: dts: ti: k3-j784s4-evm: " Apurva Nandan
2023-08-07 18:56   ` Apurva Nandan
2023-08-07 18:56 ` Apurva Nandan [this message]
2023-08-07 18:56   ` [PATCH v2 4/4] arm64: dts: ti: k3-am69-sk: " Apurva Nandan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230807185645.128751-5-a-nandan@ti.com \
    --to=a-nandan@ti.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=hnagalla@ti.com \
    --cc=kristo@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nm@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=sabiya.d@mistralsolutions.com \
    --cc=u-kumar1@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.