All of lore.kernel.org
 help / color / mirror / Atom feed
From: Chris Morgan <macroalpha82@gmail.com>
To: linux-rockchip@lists.infradead.org
Cc: dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
	sebastian.reichel@collabora.com, daniel@ffwll.ch,
	airlied@gmail.com, sam@ravnborg.org, neil.armstrong@linaro.org,
	heiko@sntech.de, conor+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, robh+dt@kernel.org,
	Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V2 2/4] nv3051d: Add Powkiddy RK2023 Panel Support
Date: Thu,  9 Nov 2023 15:50:05 -0600	[thread overview]
Message-ID: <20231109215007.66826-3-macroalpha82@gmail.com> (raw)
In-Reply-To: <20231109215007.66826-1-macroalpha82@gmail.com>

From: Chris Morgan <macromorgan@hotmail.com>

Refactor the driver to add support for the powkiddy,rk2023-panel
panel. This panel is extremely similar to the rg353p-panel but
requires a smaller vertical back porch and isn't as tolerant of
higher speeds. Note that while all of these panels are identical in
size (70x57) it is possible future panels may not be.

Tested on my RG351V, RG353P, RG353V, and RK2023.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../gpu/drm/panel/panel-newvision-nv3051d.c   | 57 +++++++++++++++----
 1 file changed, 46 insertions(+), 11 deletions(-)

diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
index 79de6c886292..94d89ffd596b 100644
--- a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
+++ b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
@@ -28,6 +28,7 @@ struct nv3051d_panel_info {
 	unsigned int num_modes;
 	u16 width_mm, height_mm;
 	u32 bus_flags;
+	u32 mode_flags;
 };
 
 struct panel_nv3051d {
@@ -261,6 +262,8 @@ static int panel_nv3051d_unprepare(struct drm_panel *panel)
 
 	usleep_range(10000, 15000);
 
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
 	regulator_disable(ctx->vdd);
 
 	return 0;
@@ -385,15 +388,7 @@ static int panel_nv3051d_probe(struct mipi_dsi_device *dsi)
 
 	dsi->lanes = 4;
 	dsi->format = MIPI_DSI_FMT_RGB888;
-	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
-			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
-
-	/*
-	 * The panel in the RG351V is identical to the 353P, except it
-	 * requires MIPI_DSI_CLOCK_NON_CONTINUOUS to operate correctly.
-	 */
-	if (of_device_is_compatible(dev->of_node, "anbernic,rg351v-panel"))
-		dsi->mode_flags |= MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	dsi->mode_flags = ctx->panel_info->mode_flags;
 
 	drm_panel_init(&ctx->panel, &dsi->dev, &panel_nv3051d_funcs,
 		       DRM_MODE_CONNECTOR_DSI);
@@ -481,16 +476,56 @@ static const struct drm_display_mode nv3051d_rgxx3_modes[] = {
 	},
 };
 
-static const struct nv3051d_panel_info nv3051d_rgxx3_info = {
+static const struct drm_display_mode nv3051d_rk2023_modes[] = {
+	{
+		.hdisplay       = 640,
+		.hsync_start    = 640 + 40,
+		.hsync_end      = 640 + 40 + 2,
+		.htotal         = 640 + 40 + 2 + 80,
+		.vdisplay       = 480,
+		.vsync_start    = 480 + 18,
+		.vsync_end      = 480 + 18 + 2,
+		.vtotal         = 480 + 18 + 2 + 4,
+		.clock          = 24150,
+		.flags          = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+	},
+};
+
+static const struct nv3051d_panel_info nv3051d_rg351v_info = {
 	.display_modes = nv3051d_rgxx3_modes,
 	.num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
 	.width_mm = 70,
 	.height_mm = 57,
 	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET |
+		      MIPI_DSI_CLOCK_NON_CONTINUOUS,
+};
+
+static const struct nv3051d_panel_info nv3051d_rg353p_info = {
+	.display_modes = nv3051d_rgxx3_modes,
+	.num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
+	.width_mm = 70,
+	.height_mm = 57,
+	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET,
+};
+
+static const struct nv3051d_panel_info nv3051d_rk2023_info = {
+	.display_modes = nv3051d_rk2023_modes,
+	.num_modes = ARRAY_SIZE(nv3051d_rk2023_modes),
+	.width_mm = 70,
+	.height_mm = 57,
+	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET,
 };
 
 static const struct of_device_id newvision_nv3051d_of_match[] = {
-	{ .compatible = "newvision,nv3051d", .data = &nv3051d_rgxx3_info },
+	{ .compatible = "anbernic,rg351v-panel", .data = &nv3051d_rg351v_info },
+	{ .compatible = "anbernic,rg353p-panel", .data = &nv3051d_rg353p_info },
+	{ .compatible = "powkiddy,rk2023-panel", .data = &nv3051d_rk2023_info },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, newvision_nv3051d_of_match);
-- 
2.34.1


WARNING: multiple messages have this Message-ID (diff)
From: Chris Morgan <macroalpha82@gmail.com>
To: linux-rockchip@lists.infradead.org
Cc: dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
	sebastian.reichel@collabora.com, daniel@ffwll.ch,
	airlied@gmail.com, sam@ravnborg.org, neil.armstrong@linaro.org,
	heiko@sntech.de, conor+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, robh+dt@kernel.org,
	Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V2 2/4] nv3051d: Add Powkiddy RK2023 Panel Support
Date: Thu,  9 Nov 2023 15:50:05 -0600	[thread overview]
Message-ID: <20231109215007.66826-3-macroalpha82@gmail.com> (raw)
In-Reply-To: <20231109215007.66826-1-macroalpha82@gmail.com>

From: Chris Morgan <macromorgan@hotmail.com>

Refactor the driver to add support for the powkiddy,rk2023-panel
panel. This panel is extremely similar to the rg353p-panel but
requires a smaller vertical back porch and isn't as tolerant of
higher speeds. Note that while all of these panels are identical in
size (70x57) it is possible future panels may not be.

Tested on my RG351V, RG353P, RG353V, and RK2023.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../gpu/drm/panel/panel-newvision-nv3051d.c   | 57 +++++++++++++++----
 1 file changed, 46 insertions(+), 11 deletions(-)

diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
index 79de6c886292..94d89ffd596b 100644
--- a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
+++ b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
@@ -28,6 +28,7 @@ struct nv3051d_panel_info {
 	unsigned int num_modes;
 	u16 width_mm, height_mm;
 	u32 bus_flags;
+	u32 mode_flags;
 };
 
 struct panel_nv3051d {
@@ -261,6 +262,8 @@ static int panel_nv3051d_unprepare(struct drm_panel *panel)
 
 	usleep_range(10000, 15000);
 
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
 	regulator_disable(ctx->vdd);
 
 	return 0;
@@ -385,15 +388,7 @@ static int panel_nv3051d_probe(struct mipi_dsi_device *dsi)
 
 	dsi->lanes = 4;
 	dsi->format = MIPI_DSI_FMT_RGB888;
-	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
-			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
-
-	/*
-	 * The panel in the RG351V is identical to the 353P, except it
-	 * requires MIPI_DSI_CLOCK_NON_CONTINUOUS to operate correctly.
-	 */
-	if (of_device_is_compatible(dev->of_node, "anbernic,rg351v-panel"))
-		dsi->mode_flags |= MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	dsi->mode_flags = ctx->panel_info->mode_flags;
 
 	drm_panel_init(&ctx->panel, &dsi->dev, &panel_nv3051d_funcs,
 		       DRM_MODE_CONNECTOR_DSI);
@@ -481,16 +476,56 @@ static const struct drm_display_mode nv3051d_rgxx3_modes[] = {
 	},
 };
 
-static const struct nv3051d_panel_info nv3051d_rgxx3_info = {
+static const struct drm_display_mode nv3051d_rk2023_modes[] = {
+	{
+		.hdisplay       = 640,
+		.hsync_start    = 640 + 40,
+		.hsync_end      = 640 + 40 + 2,
+		.htotal         = 640 + 40 + 2 + 80,
+		.vdisplay       = 480,
+		.vsync_start    = 480 + 18,
+		.vsync_end      = 480 + 18 + 2,
+		.vtotal         = 480 + 18 + 2 + 4,
+		.clock          = 24150,
+		.flags          = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+	},
+};
+
+static const struct nv3051d_panel_info nv3051d_rg351v_info = {
 	.display_modes = nv3051d_rgxx3_modes,
 	.num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
 	.width_mm = 70,
 	.height_mm = 57,
 	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET |
+		      MIPI_DSI_CLOCK_NON_CONTINUOUS,
+};
+
+static const struct nv3051d_panel_info nv3051d_rg353p_info = {
+	.display_modes = nv3051d_rgxx3_modes,
+	.num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
+	.width_mm = 70,
+	.height_mm = 57,
+	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET,
+};
+
+static const struct nv3051d_panel_info nv3051d_rk2023_info = {
+	.display_modes = nv3051d_rk2023_modes,
+	.num_modes = ARRAY_SIZE(nv3051d_rk2023_modes),
+	.width_mm = 70,
+	.height_mm = 57,
+	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET,
 };
 
 static const struct of_device_id newvision_nv3051d_of_match[] = {
-	{ .compatible = "newvision,nv3051d", .data = &nv3051d_rgxx3_info },
+	{ .compatible = "anbernic,rg351v-panel", .data = &nv3051d_rg351v_info },
+	{ .compatible = "anbernic,rg353p-panel", .data = &nv3051d_rg353p_info },
+	{ .compatible = "powkiddy,rk2023-panel", .data = &nv3051d_rk2023_info },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, newvision_nv3051d_of_match);
-- 
2.34.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

WARNING: multiple messages have this Message-ID (diff)
From: Chris Morgan <macroalpha82@gmail.com>
To: linux-rockchip@lists.infradead.org
Cc: devicetree@vger.kernel.org, conor+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, neil.armstrong@linaro.org,
	sam@ravnborg.org, Chris Morgan <macromorgan@hotmail.com>,
	sebastian.reichel@collabora.com, dri-devel@lists.freedesktop.org,
	robh+dt@kernel.org
Subject: [PATCH V2 2/4] nv3051d: Add Powkiddy RK2023 Panel Support
Date: Thu,  9 Nov 2023 15:50:05 -0600	[thread overview]
Message-ID: <20231109215007.66826-3-macroalpha82@gmail.com> (raw)
In-Reply-To: <20231109215007.66826-1-macroalpha82@gmail.com>

From: Chris Morgan <macromorgan@hotmail.com>

Refactor the driver to add support for the powkiddy,rk2023-panel
panel. This panel is extremely similar to the rg353p-panel but
requires a smaller vertical back porch and isn't as tolerant of
higher speeds. Note that while all of these panels are identical in
size (70x57) it is possible future panels may not be.

Tested on my RG351V, RG353P, RG353V, and RK2023.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../gpu/drm/panel/panel-newvision-nv3051d.c   | 57 +++++++++++++++----
 1 file changed, 46 insertions(+), 11 deletions(-)

diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
index 79de6c886292..94d89ffd596b 100644
--- a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
+++ b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
@@ -28,6 +28,7 @@ struct nv3051d_panel_info {
 	unsigned int num_modes;
 	u16 width_mm, height_mm;
 	u32 bus_flags;
+	u32 mode_flags;
 };
 
 struct panel_nv3051d {
@@ -261,6 +262,8 @@ static int panel_nv3051d_unprepare(struct drm_panel *panel)
 
 	usleep_range(10000, 15000);
 
+	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+
 	regulator_disable(ctx->vdd);
 
 	return 0;
@@ -385,15 +388,7 @@ static int panel_nv3051d_probe(struct mipi_dsi_device *dsi)
 
 	dsi->lanes = 4;
 	dsi->format = MIPI_DSI_FMT_RGB888;
-	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
-			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
-
-	/*
-	 * The panel in the RG351V is identical to the 353P, except it
-	 * requires MIPI_DSI_CLOCK_NON_CONTINUOUS to operate correctly.
-	 */
-	if (of_device_is_compatible(dev->of_node, "anbernic,rg351v-panel"))
-		dsi->mode_flags |= MIPI_DSI_CLOCK_NON_CONTINUOUS;
+	dsi->mode_flags = ctx->panel_info->mode_flags;
 
 	drm_panel_init(&ctx->panel, &dsi->dev, &panel_nv3051d_funcs,
 		       DRM_MODE_CONNECTOR_DSI);
@@ -481,16 +476,56 @@ static const struct drm_display_mode nv3051d_rgxx3_modes[] = {
 	},
 };
 
-static const struct nv3051d_panel_info nv3051d_rgxx3_info = {
+static const struct drm_display_mode nv3051d_rk2023_modes[] = {
+	{
+		.hdisplay       = 640,
+		.hsync_start    = 640 + 40,
+		.hsync_end      = 640 + 40 + 2,
+		.htotal         = 640 + 40 + 2 + 80,
+		.vdisplay       = 480,
+		.vsync_start    = 480 + 18,
+		.vsync_end      = 480 + 18 + 2,
+		.vtotal         = 480 + 18 + 2 + 4,
+		.clock          = 24150,
+		.flags          = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+	},
+};
+
+static const struct nv3051d_panel_info nv3051d_rg351v_info = {
 	.display_modes = nv3051d_rgxx3_modes,
 	.num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
 	.width_mm = 70,
 	.height_mm = 57,
 	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET |
+		      MIPI_DSI_CLOCK_NON_CONTINUOUS,
+};
+
+static const struct nv3051d_panel_info nv3051d_rg353p_info = {
+	.display_modes = nv3051d_rgxx3_modes,
+	.num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
+	.width_mm = 70,
+	.height_mm = 57,
+	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET,
+};
+
+static const struct nv3051d_panel_info nv3051d_rk2023_info = {
+	.display_modes = nv3051d_rk2023_modes,
+	.num_modes = ARRAY_SIZE(nv3051d_rk2023_modes),
+	.width_mm = 70,
+	.height_mm = 57,
+	.bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+		      MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET,
 };
 
 static const struct of_device_id newvision_nv3051d_of_match[] = {
-	{ .compatible = "newvision,nv3051d", .data = &nv3051d_rgxx3_info },
+	{ .compatible = "anbernic,rg351v-panel", .data = &nv3051d_rg351v_info },
+	{ .compatible = "anbernic,rg353p-panel", .data = &nv3051d_rg353p_info },
+	{ .compatible = "powkiddy,rk2023-panel", .data = &nv3051d_rk2023_info },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, newvision_nv3051d_of_match);
-- 
2.34.1


  parent reply	other threads:[~2023-11-09 21:50 UTC|newest]

Thread overview: 39+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-11-09 21:50 [PATCH V2 0/4] rockchip: Add Powkiddy RK2023 Chris Morgan
2023-11-09 21:50 ` Chris Morgan
2023-11-09 21:50 ` Chris Morgan
2023-11-09 21:50 ` [PATCH V2 1/4] dt-bindings: display: panel: Update NewVision NV3051D compatibles Chris Morgan
2023-11-09 21:50   ` Chris Morgan
2023-11-09 21:50   ` Chris Morgan
2023-11-10 13:11   ` Krzysztof Kozlowski
2023-11-10 13:11     ` Krzysztof Kozlowski
2023-11-10 13:11     ` Krzysztof Kozlowski
2023-11-10 14:28     ` Chris Morgan
2023-11-10 14:28       ` Chris Morgan
2023-11-10 14:28       ` Chris Morgan
2023-11-10 14:52       ` Krzysztof Kozlowski
2023-11-10 14:52         ` Krzysztof Kozlowski
2023-11-10 14:52         ` Krzysztof Kozlowski
2023-11-09 21:50 ` Chris Morgan [this message]
2023-11-09 21:50   ` [PATCH V2 2/4] nv3051d: Add Powkiddy RK2023 Panel Support Chris Morgan
2023-11-09 21:50   ` Chris Morgan
2023-11-15 22:37   ` Jessica Zhang
2023-11-15 22:37     ` Jessica Zhang
2023-11-15 22:37     ` Jessica Zhang
2023-11-09 21:50 ` [PATCH V2 3/4] dt-bindings: arm: rockchip: Add Powkiddy RK2023 Chris Morgan
2023-11-09 21:50   ` Chris Morgan
2023-11-09 21:50   ` Chris Morgan
2023-11-10 13:12   ` Krzysztof Kozlowski
2023-11-10 13:12     ` Krzysztof Kozlowski
2023-11-10 13:12     ` Krzysztof Kozlowski
2023-11-09 21:50 ` [PATCH V2 4/4] arm64: dts: rockchip: add " Chris Morgan
2023-11-09 21:50   ` Chris Morgan
2023-11-09 21:50   ` Chris Morgan
2023-11-10 13:14   ` Krzysztof Kozlowski
2023-11-10 13:14     ` Krzysztof Kozlowski
2023-11-10 13:14     ` Krzysztof Kozlowski
2023-11-10 14:30     ` Chris Morgan
2023-11-10 14:30       ` Chris Morgan
2023-11-10 14:30       ` Chris Morgan
2023-11-10 15:02       ` Krzysztof Kozlowski
2023-11-10 15:02         ` Krzysztof Kozlowski
2023-11-10 15:02         ` Krzysztof Kozlowski

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20231109215007.66826-3-macroalpha82@gmail.com \
    --to=macroalpha82@gmail.com \
    --cc=airlied@gmail.com \
    --cc=conor+dt@kernel.org \
    --cc=daniel@ffwll.ch \
    --cc=devicetree@vger.kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=heiko@sntech.de \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=macromorgan@hotmail.com \
    --cc=neil.armstrong@linaro.org \
    --cc=robh+dt@kernel.org \
    --cc=sam@ravnborg.org \
    --cc=sebastian.reichel@collabora.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.