From: Tanmay Shah <tanmay.shah@amd.com> To: <andersson@kernel.org>, <mathieu.poirier@linaro.org>, <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>, <conor+dt@kernel.org>, <michal.simek@amd.com>, <ben.levinsky@amd.com>, <tanmay.shah@amd.com> Cc: <linux-remoteproc@vger.kernel.org>, <devicetree@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org>, <linux-kernel@vger.kernel.org> Subject: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc Date: Fri, 15 Dec 2023 15:57:24 -0800 [thread overview] Message-ID: <20231215235725.1247350-3-tanmay.shah@amd.com> (raw) In-Reply-To: <20231215235725.1247350-1-tanmay.shah@amd.com> Add properties as per new bindings in zynqmp remoteproc node to represent TCM address and size. This patch also adds alternative remoteproc node to represent remoteproc cluster in split mode. By default lockstep mode is enabled and users should disable it before using split mode dts. Both device-tree nodes can't be used simultaneously one of them must be disabled. For zcu102-1.0 and zcu102-1.1 board remoteproc split mode dts node is enabled and lockstep mode dts is disabled. Signed-off-by: Tanmay Shah <tanmay.shah@amd.com> --- .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++-- 2 files changed, 63 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts index c8f71a1aec89..495ca94b45db 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts @@ -14,6 +14,14 @@ / { compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp"; }; +&rproc_split { + status = "okay"; +}; + +&rproc_lockstep { + status = "disabled"; +}; + &eeprom { #address-cells = <1>; #size-cells = <1>; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index b61fc99cd911..602e6aba7ac5 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -247,19 +247,69 @@ fpga_full: fpga-full { ranges; }; - remoteproc { + rproc_lockstep: remoteproc@ffe00000 { compatible = "xlnx,zynqmp-r5fss"; xlnx,cluster-mode = <1>; - r5f-0 { + #address-cells = <2>; + #size-cells = <2>; + + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>, + <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>, + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>, + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>; + + r5f@0 { + compatible = "xlnx,zynqmp-r5f"; + reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_0>, + <&zynqmp_firmware PD_R5_0_ATCM>, + <&zynqmp_firmware PD_R5_0_BTCM>; + memory-region = <&rproc_0_fw_image>; + }; + + r5f@1 { + compatible = "xlnx,zynqmp-r5f"; + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_1>, + <&zynqmp_firmware PD_R5_1_ATCM>, + <&zynqmp_firmware PD_R5_1_BTCM>; + memory-region = <&rproc_1_fw_image>; + }; + }; + + rproc_split: remoteproc-split@ffe00000 { + status = "disabled"; + compatible = "xlnx,zynqmp-r5fss"; + xlnx,cluster-mode = <0>; + + #address-cells = <2>; + #size-cells = <2>; + + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>, + <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>, + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>, + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>; + + r5f@0 { compatible = "xlnx,zynqmp-r5f"; - power-domains = <&zynqmp_firmware PD_RPU_0>; + reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_0>, + <&zynqmp_firmware PD_R5_0_ATCM>, + <&zynqmp_firmware PD_R5_0_BTCM>; memory-region = <&rproc_0_fw_image>; }; - r5f-1 { + r5f@1 { compatible = "xlnx,zynqmp-r5f"; - power-domains = <&zynqmp_firmware PD_RPU_1>; + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_1>, + <&zynqmp_firmware PD_R5_1_ATCM>, + <&zynqmp_firmware PD_R5_1_BTCM>; memory-region = <&rproc_1_fw_image>; }; }; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Tanmay Shah <tanmay.shah@amd.com> To: <andersson@kernel.org>, <mathieu.poirier@linaro.org>, <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>, <conor+dt@kernel.org>, <michal.simek@amd.com>, <ben.levinsky@amd.com>, <tanmay.shah@amd.com> Cc: <linux-remoteproc@vger.kernel.org>, <devicetree@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org>, <linux-kernel@vger.kernel.org> Subject: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc Date: Fri, 15 Dec 2023 15:57:24 -0800 [thread overview] Message-ID: <20231215235725.1247350-3-tanmay.shah@amd.com> (raw) In-Reply-To: <20231215235725.1247350-1-tanmay.shah@amd.com> Add properties as per new bindings in zynqmp remoteproc node to represent TCM address and size. This patch also adds alternative remoteproc node to represent remoteproc cluster in split mode. By default lockstep mode is enabled and users should disable it before using split mode dts. Both device-tree nodes can't be used simultaneously one of them must be disabled. For zcu102-1.0 and zcu102-1.1 board remoteproc split mode dts node is enabled and lockstep mode dts is disabled. Signed-off-by: Tanmay Shah <tanmay.shah@amd.com> --- .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++-- 2 files changed, 63 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts index c8f71a1aec89..495ca94b45db 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts @@ -14,6 +14,14 @@ / { compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp"; }; +&rproc_split { + status = "okay"; +}; + +&rproc_lockstep { + status = "disabled"; +}; + &eeprom { #address-cells = <1>; #size-cells = <1>; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index b61fc99cd911..602e6aba7ac5 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -247,19 +247,69 @@ fpga_full: fpga-full { ranges; }; - remoteproc { + rproc_lockstep: remoteproc@ffe00000 { compatible = "xlnx,zynqmp-r5fss"; xlnx,cluster-mode = <1>; - r5f-0 { + #address-cells = <2>; + #size-cells = <2>; + + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>, + <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>, + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>, + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>; + + r5f@0 { + compatible = "xlnx,zynqmp-r5f"; + reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_0>, + <&zynqmp_firmware PD_R5_0_ATCM>, + <&zynqmp_firmware PD_R5_0_BTCM>; + memory-region = <&rproc_0_fw_image>; + }; + + r5f@1 { + compatible = "xlnx,zynqmp-r5f"; + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_1>, + <&zynqmp_firmware PD_R5_1_ATCM>, + <&zynqmp_firmware PD_R5_1_BTCM>; + memory-region = <&rproc_1_fw_image>; + }; + }; + + rproc_split: remoteproc-split@ffe00000 { + status = "disabled"; + compatible = "xlnx,zynqmp-r5fss"; + xlnx,cluster-mode = <0>; + + #address-cells = <2>; + #size-cells = <2>; + + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>, + <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>, + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>, + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>; + + r5f@0 { compatible = "xlnx,zynqmp-r5f"; - power-domains = <&zynqmp_firmware PD_RPU_0>; + reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_0>, + <&zynqmp_firmware PD_R5_0_ATCM>, + <&zynqmp_firmware PD_R5_0_BTCM>; memory-region = <&rproc_0_fw_image>; }; - r5f-1 { + r5f@1 { compatible = "xlnx,zynqmp-r5f"; - power-domains = <&zynqmp_firmware PD_RPU_1>; + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>; + reg-names = "atcm", "btcm"; + power-domains = <&zynqmp_firmware PD_RPU_1>, + <&zynqmp_firmware PD_R5_1_ATCM>, + <&zynqmp_firmware PD_R5_1_BTCM>; memory-region = <&rproc_1_fw_image>; }; }; -- 2.25.1
next prev parent reply other threads:[~2023-12-15 23:59 UTC|newest] Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top 2023-12-15 23:57 [PATCH v8 0/3] add zynqmp TCM bindings Tanmay Shah 2023-12-15 23:57 ` Tanmay Shah 2023-12-15 23:57 ` [PATCH v8 1/3] dt-bindings: remoteproc: add Tightly Coupled Memory (TCM) bindings Tanmay Shah 2023-12-15 23:57 ` Tanmay Shah 2023-12-15 23:57 ` Tanmay Shah [this message] 2023-12-15 23:57 ` [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc Tanmay Shah 2023-12-20 13:14 ` Michal Simek 2023-12-20 13:14 ` Michal Simek 2023-12-20 14:45 ` Tanmay Shah 2023-12-20 14:45 ` Tanmay Shah 2023-12-23 14:34 ` Mathieu Poirier 2023-12-23 14:34 ` Mathieu Poirier 2024-01-03 17:54 ` Mathieu Poirier 2024-01-03 17:54 ` Mathieu Poirier 2024-01-03 18:19 ` Tanmay Shah 2024-01-03 18:19 ` Tanmay Shah 2023-12-15 23:57 ` [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree Tanmay Shah 2023-12-15 23:57 ` Tanmay Shah 2024-01-03 18:17 ` Mathieu Poirier 2024-01-03 18:17 ` Mathieu Poirier 2024-01-03 18:51 ` Tanmay Shah 2024-01-03 18:51 ` Tanmay Shah 2024-01-04 16:14 ` Tanmay Shah 2024-01-04 16:14 ` Tanmay Shah 2024-01-08 17:25 ` Mathieu Poirier 2024-01-08 17:25 ` Mathieu Poirier
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20231215235725.1247350-3-tanmay.shah@amd.com \ --to=tanmay.shah@amd.com \ --cc=andersson@kernel.org \ --cc=ben.levinsky@amd.com \ --cc=conor+dt@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-remoteproc@vger.kernel.org \ --cc=mathieu.poirier@linaro.org \ --cc=michal.simek@amd.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.