From: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> To: Emil Renner Berthing <kernel@esmil.dk>, Conor Dooley <conor@kernel.org>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Paul Walmsley <paul.walmsley@sifive.com>, Palmer Dabbelt <palmer@dabbelt.com>, Albert Ou <aou@eecs.berkeley.edu>, Richard Cochran <richardcochran@gmail.com>, Andrew Lunn <andrew@lunn.ch>, Jacob Keller <jacob.e.keller@intel.com> Cc: linux-riscv@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, netdev@vger.kernel.org, kernel@collabora.com, Emil Renner Berthing <emil.renner.berthing@canonical.com> Subject: [PATCH v6 2/4] riscv: dts: starfive: jh7100-common: Setup pinmux and enable gmac Date: Wed, 20 Dec 2023 23:17:40 +0200 [thread overview] Message-ID: <20231220211743.2490518-3-cristian.ciocaltea@collabora.com> (raw) In-Reply-To: <20231220211743.2490518-1-cristian.ciocaltea@collabora.com> Add pinmux configuration for DWMAC found on the JH7100 based boards and enable the related DT node, providing a basic PHY configuration. Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> --- .../boot/dts/starfive/jh7100-common.dtsi | 84 +++++++++++++++++++ 1 file changed, 84 insertions(+) diff --git a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi index 42fb61c36068..bcba08e5bdf2 100644 --- a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi @@ -72,7 +72,91 @@ wifi_pwrseq: wifi-pwrseq { }; }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins>; + phy-mode = "rgmii-id"; + status = "okay"; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; +}; + &gpio { + gmac_pins: gmac-0 { + gtxclk-pins { + pins = <PAD_FUNC_SHARE(115)>; + bias-pull-up; + drive-strength = <35>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + miitxclk-pins { + pins = <PAD_FUNC_SHARE(116)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-disable; + slew-rate = <0>; + }; + tx-pins { + pins = <PAD_FUNC_SHARE(117)>, + <PAD_FUNC_SHARE(119)>, + <PAD_FUNC_SHARE(120)>, + <PAD_FUNC_SHARE(121)>, + <PAD_FUNC_SHARE(122)>, + <PAD_FUNC_SHARE(123)>, + <PAD_FUNC_SHARE(124)>, + <PAD_FUNC_SHARE(125)>, + <PAD_FUNC_SHARE(126)>; + bias-pull-up; + drive-strength = <35>; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + rxclk-pins { + pins = <PAD_FUNC_SHARE(127)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-disable; + slew-rate = <6>; + }; + rxer-pins { + pins = <PAD_FUNC_SHARE(129)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-disable; + slew-rate = <0>; + }; + rx-pins { + pins = <PAD_FUNC_SHARE(128)>, + <PAD_FUNC_SHARE(130)>, + <PAD_FUNC_SHARE(131)>, + <PAD_FUNC_SHARE(132)>, + <PAD_FUNC_SHARE(133)>, + <PAD_FUNC_SHARE(134)>, + <PAD_FUNC_SHARE(135)>, + <PAD_FUNC_SHARE(136)>, + <PAD_FUNC_SHARE(137)>, + <PAD_FUNC_SHARE(138)>, + <PAD_FUNC_SHARE(139)>, + <PAD_FUNC_SHARE(140)>, + <PAD_FUNC_SHARE(141)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + }; + i2c0_pins: i2c0-0 { i2c-pins { pinmux = <GPIOMUX(62, GPO_LOW, -- 2.43.0
WARNING: multiple messages have this Message-ID (diff)
From: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> To: Emil Renner Berthing <kernel@esmil.dk>, Conor Dooley <conor@kernel.org>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Paul Walmsley <paul.walmsley@sifive.com>, Palmer Dabbelt <palmer@dabbelt.com>, Albert Ou <aou@eecs.berkeley.edu>, Richard Cochran <richardcochran@gmail.com>, Andrew Lunn <andrew@lunn.ch>, Jacob Keller <jacob.e.keller@intel.com> Cc: linux-riscv@lists.infradead.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, netdev@vger.kernel.org, kernel@collabora.com, Emil Renner Berthing <emil.renner.berthing@canonical.com> Subject: [PATCH v6 2/4] riscv: dts: starfive: jh7100-common: Setup pinmux and enable gmac Date: Wed, 20 Dec 2023 23:17:40 +0200 [thread overview] Message-ID: <20231220211743.2490518-3-cristian.ciocaltea@collabora.com> (raw) In-Reply-To: <20231220211743.2490518-1-cristian.ciocaltea@collabora.com> Add pinmux configuration for DWMAC found on the JH7100 based boards and enable the related DT node, providing a basic PHY configuration. Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> --- .../boot/dts/starfive/jh7100-common.dtsi | 84 +++++++++++++++++++ 1 file changed, 84 insertions(+) diff --git a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi index 42fb61c36068..bcba08e5bdf2 100644 --- a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi @@ -72,7 +72,91 @@ wifi_pwrseq: wifi-pwrseq { }; }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins>; + phy-mode = "rgmii-id"; + status = "okay"; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; +}; + &gpio { + gmac_pins: gmac-0 { + gtxclk-pins { + pins = <PAD_FUNC_SHARE(115)>; + bias-pull-up; + drive-strength = <35>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + miitxclk-pins { + pins = <PAD_FUNC_SHARE(116)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-disable; + slew-rate = <0>; + }; + tx-pins { + pins = <PAD_FUNC_SHARE(117)>, + <PAD_FUNC_SHARE(119)>, + <PAD_FUNC_SHARE(120)>, + <PAD_FUNC_SHARE(121)>, + <PAD_FUNC_SHARE(122)>, + <PAD_FUNC_SHARE(123)>, + <PAD_FUNC_SHARE(124)>, + <PAD_FUNC_SHARE(125)>, + <PAD_FUNC_SHARE(126)>; + bias-pull-up; + drive-strength = <35>; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + rxclk-pins { + pins = <PAD_FUNC_SHARE(127)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-disable; + slew-rate = <6>; + }; + rxer-pins { + pins = <PAD_FUNC_SHARE(129)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-disable; + slew-rate = <0>; + }; + rx-pins { + pins = <PAD_FUNC_SHARE(128)>, + <PAD_FUNC_SHARE(130)>, + <PAD_FUNC_SHARE(131)>, + <PAD_FUNC_SHARE(132)>, + <PAD_FUNC_SHARE(133)>, + <PAD_FUNC_SHARE(134)>, + <PAD_FUNC_SHARE(135)>, + <PAD_FUNC_SHARE(136)>, + <PAD_FUNC_SHARE(137)>, + <PAD_FUNC_SHARE(138)>, + <PAD_FUNC_SHARE(139)>, + <PAD_FUNC_SHARE(140)>, + <PAD_FUNC_SHARE(141)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + }; + i2c0_pins: i2c0-0 { i2c-pins { pinmux = <GPIOMUX(62, GPO_LOW, -- 2.43.0 _______________________________________________ linux-riscv mailing list linux-riscv@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-riscv
next prev parent reply other threads:[~2023-12-20 21:17 UTC|newest] Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top 2023-12-20 21:17 [PATCH v6 0/4] Enable networking support for StarFive JH7100 SoC Cristian Ciocaltea 2023-12-20 21:17 ` Cristian Ciocaltea 2023-12-20 21:17 ` [PATCH v6 1/4] riscv: dts: starfive: jh7100: Add sysmain and gmac DT nodes Cristian Ciocaltea 2023-12-20 21:17 ` Cristian Ciocaltea 2023-12-20 21:17 ` Cristian Ciocaltea [this message] 2023-12-20 21:17 ` [PATCH v6 2/4] riscv: dts: starfive: jh7100-common: Setup pinmux and enable gmac Cristian Ciocaltea 2023-12-20 21:17 ` [PATCH v6 3/4] riscv: dts: starfive: visionfive-v1: Setup ethernet phy Cristian Ciocaltea 2023-12-20 21:17 ` Cristian Ciocaltea 2023-12-20 21:17 ` [PATCH v6 4/4] riscv: dts: starfive: beaglev-starlight: Setup phy reset gpio Cristian Ciocaltea 2023-12-20 21:17 ` Cristian Ciocaltea 2023-12-26 20:38 ` [PATCH v6 0/4] Enable networking support for StarFive JH7100 SoC Emil Renner Berthing 2023-12-26 20:38 ` Emil Renner Berthing 2024-01-10 13:57 ` Conor Dooley 2024-01-10 13:57 ` Conor Dooley 2024-01-10 16:17 ` Cristian Ciocaltea 2024-01-10 16:17 ` Cristian Ciocaltea 2024-01-31 11:29 ` Cristian Ciocaltea 2024-01-31 11:29 ` Cristian Ciocaltea 2024-01-31 12:25 ` Conor Dooley 2024-01-31 12:25 ` Conor Dooley
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20231220211743.2490518-3-cristian.ciocaltea@collabora.com \ --to=cristian.ciocaltea@collabora.com \ --cc=andrew@lunn.ch \ --cc=aou@eecs.berkeley.edu \ --cc=conor@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=emil.renner.berthing@canonical.com \ --cc=jacob.e.keller@intel.com \ --cc=kernel@collabora.com \ --cc=kernel@esmil.dk \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-riscv@lists.infradead.org \ --cc=netdev@vger.kernel.org \ --cc=palmer@dabbelt.com \ --cc=paul.walmsley@sifive.com \ --cc=richardcochran@gmail.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.