From: Sam Protsenko <semen.protsenko@linaro.org> To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Rob Herring <robh+dt@kernel.org>, Conor Dooley <conor+dt@kernel.org> Cc: Tudor Ambarus <tudor.ambarus@linaro.org>, Alim Akhtar <alim.akhtar@samsung.com>, Sylwester Nawrocki <s.nawrocki@samsung.com>, Tomasz Figa <tomasz.figa@gmail.com>, Chanwoo Choi <cw00.choi@samsung.com>, linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH v2 1/3] clk: samsung: exynos850: Propagate SPI IPCLK rate change Date: Wed, 24 Jan 2024 19:38:56 -0600 [thread overview] Message-ID: <20240125013858.3986-2-semen.protsenko@linaro.org> (raw) In-Reply-To: <20240125013858.3986-1-semen.protsenko@linaro.org> When SPI transfer is being prepared, the spi-s3c64xx driver will call clk_set_rate() to change the rate of SPI source clock (IPCLK). But IPCLK is a gate (leaf) clock, so it must propagate the rate change up the clock tree, so that corresponding DIV clocks can actually change their divider values. Add CLK_SET_RATE_PARENT flag to corresponding clocks for all SPI instances in Exynos850 (spi_0, spi_1 and spi_2) to make it possible. This change involves next clocks: usi_spi_0: Clock Block Div range -------------------------------------------- gout_spi0_ipclk CMU_PERI - dout_peri_spi0 CMU_PERI /1..32 mout_peri_spi_user CMU_PERI - dout_peri_ip CMU_TOP /1..16 usi_cmgp0: Clock Block Div range -------------------------------------------- gout_cmgp_usi0_ipclk CMU_CMGP - dout_cmgp_usi0 CMU_CMGP /1..32 mout_cmgp_usi0 CMU_CMGP - gout_clkcmu_cmgp_bus CMU_APM - dout_apm_bus CMU_APM /1..8 usi_cmgp1: Clock Block Div range -------------------------------------------- gout_cmgp_usi1_ipclk CMU_CMGP - dout_cmgp_usi1 CMU_CMGP /1..32 mout_cmgp_usi1 CMU_CMGP - gout_clkcmu_cmgp_bus CMU_APM - dout_apm_bus CMU_APM /1..8 With input clock of 400 MHz, this scheme provides next IPCLK rate range, for each SPI block: SPI0: 781 kHz ... 400 MHz SPI1/2: 1.6 MHz ... 400 MHz Accounting for internal /4 divider in SPI blocks, and because the max SPI frequency is limited at 50 MHz, it gives us next SPI SCK rates: SPI0: 200 kHz ... 49.9 MHz SPI1/2: 400 kHz ... 49.9 MHz Which should cover all possible applications of SPI bus. Of course, setting SPI frequency to values as low as 500 kHz will also affect the common bus dividers (dout_apm_bus or dout_peri_ip), which in turn effectively lowers the rates for all leaf bus clocks derived from those dividers, like HSI2C and I3C clocks. But at least it gives the board designer a choice, whether to keep all clocks (SPI/HSI2C/I3C) at high frequencies, or make all those clocks have lower frequencies. Not propagating the rate change to those common dividers would limit this choice to "only high frequencies are allowed for SPI/HSI2C/I3C" option, making the common dividers useless. This decision follows the "Worse is better" approach, relying on the users/engineers to know the system internals when working with such low-level features, instead of trying to account for all possible use-cases. Fixes: 7dd05578198b ("clk: samsung: Introduce Exynos850 clock driver") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> --- Changes in v2: - Fixed indentation to make checkpatch strict happy drivers/clk/samsung/clk-exynos850.c | 33 +++++++++++++++-------------- 1 file changed, 17 insertions(+), 16 deletions(-) diff --git a/drivers/clk/samsung/clk-exynos850.c b/drivers/clk/samsung/clk-exynos850.c index 01913dc4eb27..82cfa22c0788 100644 --- a/drivers/clk/samsung/clk-exynos850.c +++ b/drivers/clk/samsung/clk-exynos850.c @@ -605,7 +605,7 @@ static const struct samsung_div_clock apm_div_clks[] __initconst = { static const struct samsung_gate_clock apm_gate_clks[] __initconst = { GATE(CLK_GOUT_CLKCMU_CMGP_BUS, "gout_clkcmu_cmgp_bus", "dout_apm_bus", - CLK_CON_GAT_CLKCMU_CMGP_BUS, 21, 0, 0), + CLK_CON_GAT_CLKCMU_CMGP_BUS, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_CLKCMU_CHUB_BUS, "gout_clkcmu_chub_bus", "mout_clkcmu_chub_bus", CLK_CON_GAT_GATE_CLKCMU_CHUB_BUS, 21, 0, 0), @@ -974,19 +974,19 @@ static const struct samsung_fixed_rate_clock cmgp_fixed_clks[] __initconst = { static const struct samsung_mux_clock cmgp_mux_clks[] __initconst = { MUX(CLK_MOUT_CMGP_ADC, "mout_cmgp_adc", mout_cmgp_adc_p, CLK_CON_MUX_CLK_CMGP_ADC, 0, 1), - MUX(CLK_MOUT_CMGP_USI0, "mout_cmgp_usi0", mout_cmgp_usi0_p, - CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP0, 0, 1), - MUX(CLK_MOUT_CMGP_USI1, "mout_cmgp_usi1", mout_cmgp_usi1_p, - CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP1, 0, 1), + MUX_F(CLK_MOUT_CMGP_USI0, "mout_cmgp_usi0", mout_cmgp_usi0_p, + CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP0, 0, 1, CLK_SET_RATE_PARENT, 0), + MUX_F(CLK_MOUT_CMGP_USI1, "mout_cmgp_usi1", mout_cmgp_usi1_p, + CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP1, 0, 1, CLK_SET_RATE_PARENT, 0), }; static const struct samsung_div_clock cmgp_div_clks[] __initconst = { DIV(CLK_DOUT_CMGP_ADC, "dout_cmgp_adc", "gout_clkcmu_cmgp_bus", CLK_CON_DIV_DIV_CLK_CMGP_ADC, 0, 4), - DIV(CLK_DOUT_CMGP_USI0, "dout_cmgp_usi0", "mout_cmgp_usi0", - CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP0, 0, 5), - DIV(CLK_DOUT_CMGP_USI1, "dout_cmgp_usi1", "mout_cmgp_usi1", - CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP1, 0, 5), + DIV_F(CLK_DOUT_CMGP_USI0, "dout_cmgp_usi0", "mout_cmgp_usi0", + CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP0, 0, 5, CLK_SET_RATE_PARENT, 0), + DIV_F(CLK_DOUT_CMGP_USI1, "dout_cmgp_usi1", "mout_cmgp_usi1", + CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP1, 0, 5, CLK_SET_RATE_PARENT, 0), }; static const struct samsung_gate_clock cmgp_gate_clks[] __initconst = { @@ -1001,12 +1001,12 @@ static const struct samsung_gate_clock cmgp_gate_clks[] __initconst = { "gout_clkcmu_cmgp_bus", CLK_CON_GAT_GOUT_CMGP_GPIO_PCLK, 21, CLK_IGNORE_UNUSED, 0), GATE(CLK_GOUT_CMGP_USI0_IPCLK, "gout_cmgp_usi0_ipclk", "dout_cmgp_usi0", - CLK_CON_GAT_GOUT_CMGP_USI_CMGP0_IPCLK, 21, 0, 0), + CLK_CON_GAT_GOUT_CMGP_USI_CMGP0_IPCLK, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_CMGP_USI0_PCLK, "gout_cmgp_usi0_pclk", "gout_clkcmu_cmgp_bus", CLK_CON_GAT_GOUT_CMGP_USI_CMGP0_PCLK, 21, 0, 0), GATE(CLK_GOUT_CMGP_USI1_IPCLK, "gout_cmgp_usi1_ipclk", "dout_cmgp_usi1", - CLK_CON_GAT_GOUT_CMGP_USI_CMGP1_IPCLK, 21, 0, 0), + CLK_CON_GAT_GOUT_CMGP_USI_CMGP1_IPCLK, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_CMGP_USI1_PCLK, "gout_cmgp_usi1_pclk", "gout_clkcmu_cmgp_bus", CLK_CON_GAT_GOUT_CMGP_USI_CMGP1_PCLK, 21, 0, 0), @@ -1557,8 +1557,9 @@ static const struct samsung_mux_clock peri_mux_clks[] __initconst = { mout_peri_uart_user_p, PLL_CON0_MUX_CLKCMU_PERI_UART_USER, 4, 1), MUX(CLK_MOUT_PERI_HSI2C_USER, "mout_peri_hsi2c_user", mout_peri_hsi2c_user_p, PLL_CON0_MUX_CLKCMU_PERI_HSI2C_USER, 4, 1), - MUX(CLK_MOUT_PERI_SPI_USER, "mout_peri_spi_user", mout_peri_spi_user_p, - PLL_CON0_MUX_CLKCMU_PERI_SPI_USER, 4, 1), + MUX_F(CLK_MOUT_PERI_SPI_USER, "mout_peri_spi_user", + mout_peri_spi_user_p, PLL_CON0_MUX_CLKCMU_PERI_SPI_USER, 4, 1, + CLK_SET_RATE_PARENT, 0), }; static const struct samsung_div_clock peri_div_clks[] __initconst = { @@ -1568,8 +1569,8 @@ static const struct samsung_div_clock peri_div_clks[] __initconst = { CLK_CON_DIV_DIV_CLK_PERI_HSI2C_1, 0, 5), DIV(CLK_DOUT_PERI_HSI2C2, "dout_peri_hsi2c2", "gout_peri_hsi2c2", CLK_CON_DIV_DIV_CLK_PERI_HSI2C_2, 0, 5), - DIV(CLK_DOUT_PERI_SPI0, "dout_peri_spi0", "mout_peri_spi_user", - CLK_CON_DIV_DIV_CLK_PERI_SPI_0, 0, 5), + DIV_F(CLK_DOUT_PERI_SPI0, "dout_peri_spi0", "mout_peri_spi_user", + CLK_CON_DIV_DIV_CLK_PERI_SPI_0, 0, 5, CLK_SET_RATE_PARENT, 0), }; static const struct samsung_gate_clock peri_gate_clks[] __initconst = { @@ -1611,7 +1612,7 @@ static const struct samsung_gate_clock peri_gate_clks[] __initconst = { "mout_peri_bus_user", CLK_CON_GAT_GOUT_PERI_PWM_MOTOR_PCLK, 21, 0, 0), GATE(CLK_GOUT_SPI0_IPCLK, "gout_spi0_ipclk", "dout_peri_spi0", - CLK_CON_GAT_GOUT_PERI_SPI_0_IPCLK, 21, 0, 0), + CLK_CON_GAT_GOUT_PERI_SPI_0_IPCLK, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_SPI0_PCLK, "gout_spi0_pclk", "mout_peri_bus_user", CLK_CON_GAT_GOUT_PERI_SPI_0_PCLK, 21, 0, 0), GATE(CLK_GOUT_SYSREG_PERI_PCLK, "gout_sysreg_peri_pclk", -- 2.39.2
WARNING: multiple messages have this Message-ID (diff)
From: Sam Protsenko <semen.protsenko@linaro.org> To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Rob Herring <robh+dt@kernel.org>, Conor Dooley <conor+dt@kernel.org> Cc: Tudor Ambarus <tudor.ambarus@linaro.org>, Alim Akhtar <alim.akhtar@samsung.com>, Sylwester Nawrocki <s.nawrocki@samsung.com>, Tomasz Figa <tomasz.figa@gmail.com>, Chanwoo Choi <cw00.choi@samsung.com>, linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH v2 1/3] clk: samsung: exynos850: Propagate SPI IPCLK rate change Date: Wed, 24 Jan 2024 19:38:56 -0600 [thread overview] Message-ID: <20240125013858.3986-2-semen.protsenko@linaro.org> (raw) In-Reply-To: <20240125013858.3986-1-semen.protsenko@linaro.org> When SPI transfer is being prepared, the spi-s3c64xx driver will call clk_set_rate() to change the rate of SPI source clock (IPCLK). But IPCLK is a gate (leaf) clock, so it must propagate the rate change up the clock tree, so that corresponding DIV clocks can actually change their divider values. Add CLK_SET_RATE_PARENT flag to corresponding clocks for all SPI instances in Exynos850 (spi_0, spi_1 and spi_2) to make it possible. This change involves next clocks: usi_spi_0: Clock Block Div range -------------------------------------------- gout_spi0_ipclk CMU_PERI - dout_peri_spi0 CMU_PERI /1..32 mout_peri_spi_user CMU_PERI - dout_peri_ip CMU_TOP /1..16 usi_cmgp0: Clock Block Div range -------------------------------------------- gout_cmgp_usi0_ipclk CMU_CMGP - dout_cmgp_usi0 CMU_CMGP /1..32 mout_cmgp_usi0 CMU_CMGP - gout_clkcmu_cmgp_bus CMU_APM - dout_apm_bus CMU_APM /1..8 usi_cmgp1: Clock Block Div range -------------------------------------------- gout_cmgp_usi1_ipclk CMU_CMGP - dout_cmgp_usi1 CMU_CMGP /1..32 mout_cmgp_usi1 CMU_CMGP - gout_clkcmu_cmgp_bus CMU_APM - dout_apm_bus CMU_APM /1..8 With input clock of 400 MHz, this scheme provides next IPCLK rate range, for each SPI block: SPI0: 781 kHz ... 400 MHz SPI1/2: 1.6 MHz ... 400 MHz Accounting for internal /4 divider in SPI blocks, and because the max SPI frequency is limited at 50 MHz, it gives us next SPI SCK rates: SPI0: 200 kHz ... 49.9 MHz SPI1/2: 400 kHz ... 49.9 MHz Which should cover all possible applications of SPI bus. Of course, setting SPI frequency to values as low as 500 kHz will also affect the common bus dividers (dout_apm_bus or dout_peri_ip), which in turn effectively lowers the rates for all leaf bus clocks derived from those dividers, like HSI2C and I3C clocks. But at least it gives the board designer a choice, whether to keep all clocks (SPI/HSI2C/I3C) at high frequencies, or make all those clocks have lower frequencies. Not propagating the rate change to those common dividers would limit this choice to "only high frequencies are allowed for SPI/HSI2C/I3C" option, making the common dividers useless. This decision follows the "Worse is better" approach, relying on the users/engineers to know the system internals when working with such low-level features, instead of trying to account for all possible use-cases. Fixes: 7dd05578198b ("clk: samsung: Introduce Exynos850 clock driver") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> --- Changes in v2: - Fixed indentation to make checkpatch strict happy drivers/clk/samsung/clk-exynos850.c | 33 +++++++++++++++-------------- 1 file changed, 17 insertions(+), 16 deletions(-) diff --git a/drivers/clk/samsung/clk-exynos850.c b/drivers/clk/samsung/clk-exynos850.c index 01913dc4eb27..82cfa22c0788 100644 --- a/drivers/clk/samsung/clk-exynos850.c +++ b/drivers/clk/samsung/clk-exynos850.c @@ -605,7 +605,7 @@ static const struct samsung_div_clock apm_div_clks[] __initconst = { static const struct samsung_gate_clock apm_gate_clks[] __initconst = { GATE(CLK_GOUT_CLKCMU_CMGP_BUS, "gout_clkcmu_cmgp_bus", "dout_apm_bus", - CLK_CON_GAT_CLKCMU_CMGP_BUS, 21, 0, 0), + CLK_CON_GAT_CLKCMU_CMGP_BUS, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_CLKCMU_CHUB_BUS, "gout_clkcmu_chub_bus", "mout_clkcmu_chub_bus", CLK_CON_GAT_GATE_CLKCMU_CHUB_BUS, 21, 0, 0), @@ -974,19 +974,19 @@ static const struct samsung_fixed_rate_clock cmgp_fixed_clks[] __initconst = { static const struct samsung_mux_clock cmgp_mux_clks[] __initconst = { MUX(CLK_MOUT_CMGP_ADC, "mout_cmgp_adc", mout_cmgp_adc_p, CLK_CON_MUX_CLK_CMGP_ADC, 0, 1), - MUX(CLK_MOUT_CMGP_USI0, "mout_cmgp_usi0", mout_cmgp_usi0_p, - CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP0, 0, 1), - MUX(CLK_MOUT_CMGP_USI1, "mout_cmgp_usi1", mout_cmgp_usi1_p, - CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP1, 0, 1), + MUX_F(CLK_MOUT_CMGP_USI0, "mout_cmgp_usi0", mout_cmgp_usi0_p, + CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP0, 0, 1, CLK_SET_RATE_PARENT, 0), + MUX_F(CLK_MOUT_CMGP_USI1, "mout_cmgp_usi1", mout_cmgp_usi1_p, + CLK_CON_MUX_MUX_CLK_CMGP_USI_CMGP1, 0, 1, CLK_SET_RATE_PARENT, 0), }; static const struct samsung_div_clock cmgp_div_clks[] __initconst = { DIV(CLK_DOUT_CMGP_ADC, "dout_cmgp_adc", "gout_clkcmu_cmgp_bus", CLK_CON_DIV_DIV_CLK_CMGP_ADC, 0, 4), - DIV(CLK_DOUT_CMGP_USI0, "dout_cmgp_usi0", "mout_cmgp_usi0", - CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP0, 0, 5), - DIV(CLK_DOUT_CMGP_USI1, "dout_cmgp_usi1", "mout_cmgp_usi1", - CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP1, 0, 5), + DIV_F(CLK_DOUT_CMGP_USI0, "dout_cmgp_usi0", "mout_cmgp_usi0", + CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP0, 0, 5, CLK_SET_RATE_PARENT, 0), + DIV_F(CLK_DOUT_CMGP_USI1, "dout_cmgp_usi1", "mout_cmgp_usi1", + CLK_CON_DIV_DIV_CLK_CMGP_USI_CMGP1, 0, 5, CLK_SET_RATE_PARENT, 0), }; static const struct samsung_gate_clock cmgp_gate_clks[] __initconst = { @@ -1001,12 +1001,12 @@ static const struct samsung_gate_clock cmgp_gate_clks[] __initconst = { "gout_clkcmu_cmgp_bus", CLK_CON_GAT_GOUT_CMGP_GPIO_PCLK, 21, CLK_IGNORE_UNUSED, 0), GATE(CLK_GOUT_CMGP_USI0_IPCLK, "gout_cmgp_usi0_ipclk", "dout_cmgp_usi0", - CLK_CON_GAT_GOUT_CMGP_USI_CMGP0_IPCLK, 21, 0, 0), + CLK_CON_GAT_GOUT_CMGP_USI_CMGP0_IPCLK, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_CMGP_USI0_PCLK, "gout_cmgp_usi0_pclk", "gout_clkcmu_cmgp_bus", CLK_CON_GAT_GOUT_CMGP_USI_CMGP0_PCLK, 21, 0, 0), GATE(CLK_GOUT_CMGP_USI1_IPCLK, "gout_cmgp_usi1_ipclk", "dout_cmgp_usi1", - CLK_CON_GAT_GOUT_CMGP_USI_CMGP1_IPCLK, 21, 0, 0), + CLK_CON_GAT_GOUT_CMGP_USI_CMGP1_IPCLK, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_CMGP_USI1_PCLK, "gout_cmgp_usi1_pclk", "gout_clkcmu_cmgp_bus", CLK_CON_GAT_GOUT_CMGP_USI_CMGP1_PCLK, 21, 0, 0), @@ -1557,8 +1557,9 @@ static const struct samsung_mux_clock peri_mux_clks[] __initconst = { mout_peri_uart_user_p, PLL_CON0_MUX_CLKCMU_PERI_UART_USER, 4, 1), MUX(CLK_MOUT_PERI_HSI2C_USER, "mout_peri_hsi2c_user", mout_peri_hsi2c_user_p, PLL_CON0_MUX_CLKCMU_PERI_HSI2C_USER, 4, 1), - MUX(CLK_MOUT_PERI_SPI_USER, "mout_peri_spi_user", mout_peri_spi_user_p, - PLL_CON0_MUX_CLKCMU_PERI_SPI_USER, 4, 1), + MUX_F(CLK_MOUT_PERI_SPI_USER, "mout_peri_spi_user", + mout_peri_spi_user_p, PLL_CON0_MUX_CLKCMU_PERI_SPI_USER, 4, 1, + CLK_SET_RATE_PARENT, 0), }; static const struct samsung_div_clock peri_div_clks[] __initconst = { @@ -1568,8 +1569,8 @@ static const struct samsung_div_clock peri_div_clks[] __initconst = { CLK_CON_DIV_DIV_CLK_PERI_HSI2C_1, 0, 5), DIV(CLK_DOUT_PERI_HSI2C2, "dout_peri_hsi2c2", "gout_peri_hsi2c2", CLK_CON_DIV_DIV_CLK_PERI_HSI2C_2, 0, 5), - DIV(CLK_DOUT_PERI_SPI0, "dout_peri_spi0", "mout_peri_spi_user", - CLK_CON_DIV_DIV_CLK_PERI_SPI_0, 0, 5), + DIV_F(CLK_DOUT_PERI_SPI0, "dout_peri_spi0", "mout_peri_spi_user", + CLK_CON_DIV_DIV_CLK_PERI_SPI_0, 0, 5, CLK_SET_RATE_PARENT, 0), }; static const struct samsung_gate_clock peri_gate_clks[] __initconst = { @@ -1611,7 +1612,7 @@ static const struct samsung_gate_clock peri_gate_clks[] __initconst = { "mout_peri_bus_user", CLK_CON_GAT_GOUT_PERI_PWM_MOTOR_PCLK, 21, 0, 0), GATE(CLK_GOUT_SPI0_IPCLK, "gout_spi0_ipclk", "dout_peri_spi0", - CLK_CON_GAT_GOUT_PERI_SPI_0_IPCLK, 21, 0, 0), + CLK_CON_GAT_GOUT_PERI_SPI_0_IPCLK, 21, CLK_SET_RATE_PARENT, 0), GATE(CLK_GOUT_SPI0_PCLK, "gout_spi0_pclk", "mout_peri_bus_user", CLK_CON_GAT_GOUT_PERI_SPI_0_PCLK, 21, 0, 0), GATE(CLK_GOUT_SYSREG_PERI_PCLK, "gout_sysreg_peri_pclk", -- 2.39.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2024-01-25 1:39 UTC|newest] Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top 2024-01-25 1:38 [PATCH v2 0/3] arm64: exynos: Enable SPI for Exynos850 Sam Protsenko 2024-01-25 1:38 ` Sam Protsenko 2024-01-25 1:38 ` Sam Protsenko [this message] 2024-01-25 1:38 ` [PATCH v2 1/3] clk: samsung: exynos850: Propagate SPI IPCLK rate change Sam Protsenko 2024-01-29 17:46 ` Tudor Ambarus 2024-01-29 17:46 ` Tudor Ambarus 2024-02-01 10:36 ` (subset) " Krzysztof Kozlowski 2024-02-01 10:36 ` Krzysztof Kozlowski 2024-01-25 1:38 ` [PATCH v2 2/3] arm64: dts: exynos: Add PDMA node for Exynos850 Sam Protsenko 2024-01-25 1:38 ` Sam Protsenko 2024-02-01 10:36 ` (subset) " Krzysztof Kozlowski 2024-02-01 10:36 ` Krzysztof Kozlowski 2024-01-25 1:38 ` [PATCH v2 3/3] arm64: dts: exynos: Add SPI nodes " Sam Protsenko 2024-01-25 1:38 ` Sam Protsenko 2024-01-29 17:51 ` Tudor Ambarus 2024-01-29 17:51 ` Tudor Ambarus 2024-01-29 19:39 ` Sam Protsenko 2024-01-29 19:39 ` Sam Protsenko 2024-01-30 6:11 ` Tudor Ambarus 2024-01-30 6:11 ` Tudor Ambarus 2024-02-01 10:31 ` Krzysztof Kozlowski 2024-02-01 10:31 ` Krzysztof Kozlowski 2024-02-01 14:22 ` Sam Protsenko 2024-02-01 14:22 ` Sam Protsenko 2024-02-01 10:36 ` (subset) " Krzysztof Kozlowski 2024-02-01 10:36 ` Krzysztof Kozlowski 2024-02-01 11:56 ` Krzysztof Kozlowski 2024-02-01 11:56 ` Krzysztof Kozlowski 2024-02-01 18:24 ` Sam Protsenko 2024-02-01 18:24 ` Sam Protsenko
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20240125013858.3986-2-semen.protsenko@linaro.org \ --to=semen.protsenko@linaro.org \ --cc=alim.akhtar@samsung.com \ --cc=conor+dt@kernel.org \ --cc=cw00.choi@samsung.com \ --cc=devicetree@vger.kernel.org \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-clk@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-samsung-soc@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=s.nawrocki@samsung.com \ --cc=tomasz.figa@gmail.com \ --cc=tudor.ambarus@linaro.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.