From: Jaime Liao <jaimeliao.tw@gmail.com>
To: linux-mtd@lists.infradead.org, linux-spi@vger.kernel.org,
tudor.ambarus@linaro.org, pratyush@kernel.org, mwalle@kernel.org,
miquel.raynal@bootlin.com, richard@nod.at, vigneshr@ti.com,
broonie@kernel.org
Cc: leoyu@mxic.com.tw, jaimeliao@mxic.com.tw
Subject: [PATCH v8 9/9] mtd: spi-nor: add support for Macronix Octal flash MX66 series
Date: Thu, 1 Feb 2024 17:43:53 +0800 [thread overview]
Message-ID: <20240201094353.33281-10-jaimeliao.tw@gmail.com> (raw)
In-Reply-To: <20240201094353.33281-1-jaimeliao.tw@gmail.com>
From: JaimeLiao <jaimeliao@mxic.com.tw>
Adding Macronix Octal flash for Octal DTR support.
Adding Manufacture ID 0xC2 in last of ID table because of
Octal Flash need manufacturer fixup for enabling/disabling
Octal DTR mode.
The octaflash series can be divided into the following types:
MX66 series : Serial NOR Flash with stacked die.(Size larger than 1Gb)
LM/UM series : Up to 250MHz clock frequency with both DTR/STR operation.
LW/UW series : Support simultaneous Read-while-Write operation in multiple
bank architecture. Read-while-write feature which means read
data one bank while another bank is programing or erasing.
MX66LW : 3.0V Octal I/O with Read-while-Write and stack die
MX66UW : 1.8V Octal I/O with Read-while-Write and stack die
MX66LM : 3.0V Octal I/O with stacked die
Link: https://www.mxic.com.tw/Lists/Datasheet/Attachments/8748/MX66LM1G45G,%203V,%201Gb,%20v1.1.pdf
MX66UM : 1.8V Octal I/O with stacked die
Link: https://www.mxic.com.tw/Lists/Datasheet/Attachments/8711/MX66UM1G45G,%201.8V,%201Gb,%20v1.1.pdf
Those flash have been tested on Xilinx Zynq-picozed board using
MXIC SPI controller.
As below are debugfs data, the SFDP table and result of mtd-utils
tests dump.
---
zynq> cat jedec_id
c2803b
zynq> cat manufacturer
macronix
zynq> cat partname
mx66um1g45g
zynq> xxd -p sfdp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zynq> md5sum sfdp
eea09d64679e64f627402b39a177e356 sfdp
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/capabilities
Supported read modes by the flash
1S-1S-1S
opcode 0x13
mode cycles 0
dummy cycles 0
8D-8D-8D
opcode 0xee
mode cycles 0
dummy cycles 20
Supported page program modes by the flash
1S-1S-1S
opcode 0x12
8D-8D-8D
opcode 0x12
zynq>
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/params
name (null)
id c2 80 3b c2 80 3b
size 128 MiB
write size 1
page size 256
address nbytes 4
flags 4B_OPCODES | HAS_4BAIT | HAS_16BIT_SR | IO_MODE_EN_VOLATILE | SOFT_RESET | 1<<17
opcodes
read 0xee
dummy cycles 20
erase 0x21
program 0x12
8D extension invert
protocols
read 8D-8D-8D
write 8D-8D-8D
register 8D-8D-8D
erase commands
21 (4.00 KiB) [2]
dc (64.0 KiB) [3]
c7 (128 MiB)
sector map
region (in hex) | erase mask | flags
------------------+------------+----------
00000000-07ffffff | [ 23] |
zynq>
zynq> dd if=/dev/urandom of=./spi_test bs=1M count=2
2+0 records in
2+0 records out
2097152 bytes (2.0MB) copied, 0.099845 seconds, 20.0MB/s
zynq> mtd_debug erase /dev/mtd0 0 2097152
Erased 2097152 bytes from address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> hexdump spi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0200000
zynq> sha256sum spi_read
4bda3a28f4ffe603c0ec1258c0034d65a1a0d35ab7bd523a834608adabf03cc5 spi_read
zynq> mtd_debug write /dev/mtd0 0 2097152 spi_test
Copied 2097152 bytes from spi_test to address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> sha256sum spi_*
7f7b735ea26eb74d77203c82347a06b51e1ef1f5b9a0fda956ffc4087caa2ed8 spi_read
7f7b735ea26eb74d77203c82347a06b51e1ef1f5b9a0fda956ffc4087caa2ed8 spi_test
zynq> mtd_debug info /dev/mtd0
mtd.type = MTD_NORFLASH
mtd.flags = MTD_CAP_NORFLASH
mtd.size = 134217728 (128M)
mtd.erasesize = 4096 (4K)
mtd.writesize = 1
mtd.oobsize = 0
regions = 0
zynq> cat jedec_id
c2853b
zynq> cat manufacturer
macronix
zynq> cat partname
mx66lm1g45g
zynq> xxd -p sfdp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zynq> md5sum sfdp
7b46113b529d58a6335531a10f14a76e sfdp
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/capabilities
Supported read modes by the flash
1S-1S-1S
opcode 0x13
mode cycles 0
dummy cycles 0
8D-8D-8D
opcode 0xee
mode cycles 0
dummy cycles 14
Supported page program modes by the flash
1S-1S-1S
opcode 0x12
8D-8D-8D
opcode 0x12
zynq>
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/params
name (null)
id c2 85 3b c2 85 3b
size 128 MiB
write size 1
page size 256
address nbytes 4
flags 4B_OPCODES | HAS_4BAIT | HAS_16BIT_SR | IO_MODE_EN_VOLATILE | SOFT_RESET | 1<<17
opcodes
read 0xee
dummy cycles 14
erase 0x21
program 0x12
8D extension invert
protocols
read 8D-8D-8D
write 8D-8D-8D
register 8D-8D-8D
erase commands
21 (4.00 KiB) [2]
dc (64.0 KiB) [3]
c7 (128 MiB)
sector map
region (in hex) | erase mask | flags
------------------+------------+----------
00000000-07ffffff | [ 23] |
zynq>
zynq> dd if=/dev/urandom of=./spi_test bs=1M count=2
2+0 records in
2+0 records out
2097152 bytes (2.0MB) copied, 0.100305 seconds, 19.9MB/s
zynq> mtd_debug erase /dev/mtd0 0 2097152
Erased 2097152 bytes from address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> hexdump spi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0200000
zynq> sha256sum spi_read
4bda3a28f4ffe603c0ec1258c0034d65a1a0d35ab7bd523a834608adabf03cc5 spi_read
zynq> mtd_debug write /dev/mtd0 0 2097152 spi_test
Copied 2097152 bytes from spi_test to address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> sha256sum spi_*
5607ddcf8d16b481e78fc4e90b21795c19d1f9a7eb77182a20536cab82eb55a2 spi_read
5607ddcf8d16b481e78fc4e90b21795c19d1f9a7eb77182a20536cab82eb55a2 spi_test
zynq> mtd_debug info /dev/mtd0
mtd.type = MTD_NORFLASH
mtd.flags = MTD_CAP_NORFLASH
mtd.size = 134217728 (128M)
mtd.erasesize = 4096 (4K)
mtd.writesize = 1
mtd.oobsize = 0
regions = 0
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
---
drivers/mtd/spi-nor/macronix.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/mtd/spi-nor/macronix.c b/drivers/mtd/spi-nor/macronix.c
index 42b1e2fec4f2..ba729007a92e 100644
--- a/drivers/mtd/spi-nor/macronix.c
+++ b/drivers/mtd/spi-nor/macronix.c
@@ -262,6 +262,13 @@ static const struct flash_info macronix_nor_parts[] = {
.id = SNOR_ID(0xc2, 0x80, 0x3a),
}, {
.id = SNOR_ID(0xc2, 0x85, 0x3a),
+ }, {
+ .id = SNOR_ID(0xc2, 0x80, 0x3b),
+ }, {
+ .id = SNOR_ID(0xc2, 0x85, 0x3b),
+ }, {
+ /* Need the manufacturer fixups. Keep this last */
+ .id = SNOR_ID(0xc2),
}
};
--
2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Jaime Liao <jaimeliao.tw@gmail.com>
To: linux-mtd@lists.infradead.org, linux-spi@vger.kernel.org,
tudor.ambarus@linaro.org, pratyush@kernel.org, mwalle@kernel.org,
miquel.raynal@bootlin.com, richard@nod.at, vigneshr@ti.com,
broonie@kernel.org
Cc: leoyu@mxic.com.tw, jaimeliao@mxic.com.tw
Subject: [PATCH v8 9/9] mtd: spi-nor: add support for Macronix Octal flash MX66 series
Date: Thu, 1 Feb 2024 17:43:53 +0800 [thread overview]
Message-ID: <20240201094353.33281-10-jaimeliao.tw@gmail.com> (raw)
In-Reply-To: <20240201094353.33281-1-jaimeliao.tw@gmail.com>
From: JaimeLiao <jaimeliao@mxic.com.tw>
Adding Macronix Octal flash for Octal DTR support.
Adding Manufacture ID 0xC2 in last of ID table because of
Octal Flash need manufacturer fixup for enabling/disabling
Octal DTR mode.
The octaflash series can be divided into the following types:
MX66 series : Serial NOR Flash with stacked die.(Size larger than 1Gb)
LM/UM series : Up to 250MHz clock frequency with both DTR/STR operation.
LW/UW series : Support simultaneous Read-while-Write operation in multiple
bank architecture. Read-while-write feature which means read
data one bank while another bank is programing or erasing.
MX66LW : 3.0V Octal I/O with Read-while-Write and stack die
MX66UW : 1.8V Octal I/O with Read-while-Write and stack die
MX66LM : 3.0V Octal I/O with stacked die
Link: https://www.mxic.com.tw/Lists/Datasheet/Attachments/8748/MX66LM1G45G,%203V,%201Gb,%20v1.1.pdf
MX66UM : 1.8V Octal I/O with stacked die
Link: https://www.mxic.com.tw/Lists/Datasheet/Attachments/8711/MX66UM1G45G,%201.8V,%201Gb,%20v1.1.pdf
Those flash have been tested on Xilinx Zynq-picozed board using
MXIC SPI controller.
As below are debugfs data, the SFDP table and result of mtd-utils
tests dump.
---
zynq> cat jedec_id
c2803b
zynq> cat manufacturer
macronix
zynq> cat partname
mx66um1g45g
zynq> xxd -p sfdp
53464450080104fd00070114400000ff8701011c900000ff0a0001080001
00ff05000105200100ff84000102340100ff0000000000000000ffffffff
ffffffffe5208affffffff3f00ff00ff00ff00ffeeffffffffff00ffffff
00ff0c2010d800ff00ff897901008d1200e2cc02674430b030b0f4bdd55c
000000ff101000200000000000007ca34800000000008888000000000000
00400fd1fff30fd1fff300050090000500b1002b0095002b0096727103b8
727103b80000000090a3188200c069960000000000000000727100987271
00b8727100990000000072710098727100f872710099727100f900000000
00000000011501d0727106d8000086500000060100000000020001030002
00000000060100000000000072060002000000eec0697272717100d8f7f6
000a000014359c8043060f0021dcffff
zynq> md5sum sfdp
eea09d64679e64f627402b39a177e356 sfdp
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/capabilities
Supported read modes by the flash
1S-1S-1S
opcode 0x13
mode cycles 0
dummy cycles 0
8D-8D-8D
opcode 0xee
mode cycles 0
dummy cycles 20
Supported page program modes by the flash
1S-1S-1S
opcode 0x12
8D-8D-8D
opcode 0x12
zynq>
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/params
name (null)
id c2 80 3b c2 80 3b
size 128 MiB
write size 1
page size 256
address nbytes 4
flags 4B_OPCODES | HAS_4BAIT | HAS_16BIT_SR | IO_MODE_EN_VOLATILE | SOFT_RESET | 1<<17
opcodes
read 0xee
dummy cycles 20
erase 0x21
program 0x12
8D extension invert
protocols
read 8D-8D-8D
write 8D-8D-8D
register 8D-8D-8D
erase commands
21 (4.00 KiB) [2]
dc (64.0 KiB) [3]
c7 (128 MiB)
sector map
region (in hex) | erase mask | flags
------------------+------------+----------
00000000-07ffffff | [ 23] |
zynq>
zynq> dd if=/dev/urandom of=./spi_test bs=1M count=2
2+0 records in
2+0 records out
2097152 bytes (2.0MB) copied, 0.099845 seconds, 20.0MB/s
zynq> mtd_debug erase /dev/mtd0 0 2097152
Erased 2097152 bytes from address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> hexdump spi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0200000
zynq> sha256sum spi_read
4bda3a28f4ffe603c0ec1258c0034d65a1a0d35ab7bd523a834608adabf03cc5 spi_read
zynq> mtd_debug write /dev/mtd0 0 2097152 spi_test
Copied 2097152 bytes from spi_test to address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> sha256sum spi_*
7f7b735ea26eb74d77203c82347a06b51e1ef1f5b9a0fda956ffc4087caa2ed8 spi_read
7f7b735ea26eb74d77203c82347a06b51e1ef1f5b9a0fda956ffc4087caa2ed8 spi_test
zynq> mtd_debug info /dev/mtd0
mtd.type = MTD_NORFLASH
mtd.flags = MTD_CAP_NORFLASH
mtd.size = 134217728 (128M)
mtd.erasesize = 4096 (4K)
mtd.writesize = 1
mtd.oobsize = 0
regions = 0
zynq> cat jedec_id
c2853b
zynq> cat manufacturer
macronix
zynq> cat partname
mx66lm1g45g
zynq> xxd -p sfdp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zynq> md5sum sfdp
7b46113b529d58a6335531a10f14a76e sfdp
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/capabilities
Supported read modes by the flash
1S-1S-1S
opcode 0x13
mode cycles 0
dummy cycles 0
8D-8D-8D
opcode 0xee
mode cycles 0
dummy cycles 14
Supported page program modes by the flash
1S-1S-1S
opcode 0x12
8D-8D-8D
opcode 0x12
zynq>
zynq> cat /sys/kernel/debug/spi-nor/spi0.0/params
name (null)
id c2 85 3b c2 85 3b
size 128 MiB
write size 1
page size 256
address nbytes 4
flags 4B_OPCODES | HAS_4BAIT | HAS_16BIT_SR | IO_MODE_EN_VOLATILE | SOFT_RESET | 1<<17
opcodes
read 0xee
dummy cycles 14
erase 0x21
program 0x12
8D extension invert
protocols
read 8D-8D-8D
write 8D-8D-8D
register 8D-8D-8D
erase commands
21 (4.00 KiB) [2]
dc (64.0 KiB) [3]
c7 (128 MiB)
sector map
region (in hex) | erase mask | flags
------------------+------------+----------
00000000-07ffffff | [ 23] |
zynq>
zynq> dd if=/dev/urandom of=./spi_test bs=1M count=2
2+0 records in
2+0 records out
2097152 bytes (2.0MB) copied, 0.100305 seconds, 19.9MB/s
zynq> mtd_debug erase /dev/mtd0 0 2097152
Erased 2097152 bytes from address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> hexdump spi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0200000
zynq> sha256sum spi_read
4bda3a28f4ffe603c0ec1258c0034d65a1a0d35ab7bd523a834608adabf03cc5 spi_read
zynq> mtd_debug write /dev/mtd0 0 2097152 spi_test
Copied 2097152 bytes from spi_test to address 0x00000000 in flash
zynq> mtd_debug read /dev/mtd0 0 2097152 spi_read
Copied 2097152 bytes from address 0x00000000 in flash to spi_read
zynq> sha256sum spi_*
5607ddcf8d16b481e78fc4e90b21795c19d1f9a7eb77182a20536cab82eb55a2 spi_read
5607ddcf8d16b481e78fc4e90b21795c19d1f9a7eb77182a20536cab82eb55a2 spi_test
zynq> mtd_debug info /dev/mtd0
mtd.type = MTD_NORFLASH
mtd.flags = MTD_CAP_NORFLASH
mtd.size = 134217728 (128M)
mtd.erasesize = 4096 (4K)
mtd.writesize = 1
mtd.oobsize = 0
regions = 0
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
---
drivers/mtd/spi-nor/macronix.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/mtd/spi-nor/macronix.c b/drivers/mtd/spi-nor/macronix.c
index 42b1e2fec4f2..ba729007a92e 100644
--- a/drivers/mtd/spi-nor/macronix.c
+++ b/drivers/mtd/spi-nor/macronix.c
@@ -262,6 +262,13 @@ static const struct flash_info macronix_nor_parts[] = {
.id = SNOR_ID(0xc2, 0x80, 0x3a),
}, {
.id = SNOR_ID(0xc2, 0x85, 0x3a),
+ }, {
+ .id = SNOR_ID(0xc2, 0x80, 0x3b),
+ }, {
+ .id = SNOR_ID(0xc2, 0x85, 0x3b),
+ }, {
+ /* Need the manufacturer fixups. Keep this last */
+ .id = SNOR_ID(0xc2),
}
};
--
2.25.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2024-02-01 9:44 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-02-01 9:43 [PATCH v8 0/9] Add octal DTR support for Macronix flash Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 9:43 ` [PATCH v8 1/9] mtd: spi-nor: add Octal " Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 9:43 ` [PATCH v8 2/9] spi: spi-mem: Allow specifying the byte order in Octal DTR mode Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 12:04 ` Mark Brown
2024-02-01 12:04 ` Mark Brown
2024-02-01 15:18 ` Michael Walle
2024-02-01 15:18 ` Michael Walle
2024-02-01 9:43 ` [PATCH v8 3/9] mtd: spi-nor: core: " Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 15:28 ` Michael Walle
2024-02-01 15:28 ` Michael Walle
2024-02-01 9:43 ` [PATCH v8 4/9] mtd: spi-nor: sfdp: Get the 8D-8D-8D byte order from BFPT Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 9:43 ` [PATCH v8 5/9] spi: mxic: Add support for swapping byte Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 12:05 ` Mark Brown
2024-02-01 12:05 ` Mark Brown
2024-02-01 15:39 ` Michael Walle
2024-02-01 15:39 ` Michael Walle
2024-02-01 9:43 ` [PATCH v8 6/9] mtd: spi-nor: add support for Macronix Octal flash MX25 series with RWW feature Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 15:48 ` Michael Walle
2024-02-01 15:48 ` Michael Walle
2024-02-01 9:43 ` [PATCH v8 7/9] mtd: spi-nor: add support for Macronix Octal flash MX66 " Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 9:43 ` [PATCH v8 8/9] mtd: spi-nor: add support for Macronix Octal flash MX25 series Jaime Liao
2024-02-01 9:43 ` Jaime Liao
2024-02-01 9:43 ` Jaime Liao [this message]
2024-02-01 9:43 ` [PATCH v8 9/9] mtd: spi-nor: add support for Macronix Octal flash MX66 series Jaime Liao
2024-02-01 15:52 ` Michael Walle
2024-02-01 15:52 ` Michael Walle
2024-02-22 9:32 ` [PATCH v8 0/9] Add octal DTR support for Macronix flash Tudor Ambarus
2024-02-22 9:32 ` Tudor Ambarus
2024-02-22 9:55 ` liao jaime
2024-02-22 9:55 ` liao jaime
2024-02-26 2:02 ` Alvin Zhou
2024-02-26 2:02 ` Alvin Zhou
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240201094353.33281-10-jaimeliao.tw@gmail.com \
--to=jaimeliao.tw@gmail.com \
--cc=broonie@kernel.org \
--cc=jaimeliao@mxic.com.tw \
--cc=leoyu@mxic.com.tw \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-spi@vger.kernel.org \
--cc=miquel.raynal@bootlin.com \
--cc=mwalle@kernel.org \
--cc=pratyush@kernel.org \
--cc=richard@nod.at \
--cc=tudor.ambarus@linaro.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.