[PATCH 3/3] arm64: dts: allwinner: Add Jide Remix Mini PC support

[Andre Przywara <andre.przywara@arm.com>]

The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
	- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
	- 1 or 2 GB DRAM
	- 8 or 16 GB eMMC flash
	- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
	- RTL8723BS WiFi & Bluetooth chip
	- HDMI port
	- two USB 2.0 ports
	- 3.5mm AV port
	- microSD card slot

The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h64-remix-mini-pc.dts    | 357 ++++++++++++++++++
 2 files changed, 358 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 91d505b385de..2db3b15ad09f 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
new file mode 100644
index 000000000000..537923a541a8
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h64-remix-mini-pc.dts
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2018 ARM Ltd.
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+#include "sun50i-a64-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Remix Mini PC";
+	compatible = "jide,remix-mini-pc", "allwinner,sun50i-h64",
+		     "allwinner,sun50i-a64";
+
+	aliases {
+		ethernet1 = &rtl8723bs;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	reg_vcc5v: regulator-5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	cpvdd-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&dai {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+/* Connects to the AC200 chip */
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
+
+&i2c0_pins {
+	bias-pull-up;
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_aldo1>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723bs: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_eldo1>;
+	bus-width = <8>;
+	non-removable;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_dcdc1>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dcdc1>;
+	vcc-pe-supply = <&reg_dcdc1>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_dldo4>;
+	vcc-ph-supply = <&reg_dcdc1>;
+};
+
+&r_ir {
+	status = "okay";
+};
+
+&r_pio {
+	/*
+	 * We cannot add that supply for now since it would create a circular
+	 * dependency between pinctrl, the regulator and the RSB Bus.
+	 *
+	 * vcc-pl-supply = <&reg_aldo2>;
+	 */
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en;
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+		vin5-supply = <&reg_vcc5v>;
+		vin6-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		dldoin-supply = <&reg_vcc5v>;
+		eldoin-supply = <&reg_vcc5v>;
+		fldoin-supply = <&reg_vcc5v>;
+		drivevbus-supply = <&reg_vcc5v>;
+		ips-supply = <&reg_vcc5v>;
+
+		status = "okay";
+	};
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+/* Deviates from the reset default of 1.1V. */
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_aldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_aldo2 {
+	/* Specifying R_PIO consumer would create circular dependency. */
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+/* AC200 power supply */
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-ave-33";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-cpvdd-dram-emmc";
+};
+
+/* Supplies the arisc management core, needed by TF-A to power off cores. */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&simplefb_hdmi {
+	vcc-hdmi-supply = <&reg_dcdc1>;
+};
+
+&sound {
+	simple-audio-card,aux-devs = <&codec_analog>;
+	simple-audio-card,widgets = "Microphone", "Microphone Jack",
+				    "Headphone", "Headphone Jack";
+	simple-audio-card,routing =
+			"Left DAC", "DACL",
+			"Right DAC", "DACR",
+			"Headphone Jack", "HP",
+			"ADCL", "Left ADC",
+			"ADCR", "Right ADC",
+			"MIC2", "Microphone Jack";
+	status = "okay";
+};
+
+/* On the (unpopulated) UART pads. */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+		max-speed = <1500000>;
+	};
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_drivevbus>;
+	status = "okay";
+};
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel