From: Bhavya Kapoor <b-kapoor@ti.com> To: <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org> Cc: <nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>, <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>, <conor+dt@kernel.org>, <linux-arm-kernel@lists.infradead.org>, <b-kapoor@ti.com> Subject: [PATCH v3 4/4] arm64: dts: ti: k3-j784s4-evm: Remove Pinmux for CTS and RTS in wkup_uart0 Date: Wed, 14 Feb 2024 16:28:46 +0530 [thread overview] Message-ID: <20240214105846.1096733-5-b-kapoor@ti.com> (raw) In-Reply-To: <20240214105846.1096733-1-b-kapoor@ti.com> Only Tx and Rx Signal lines for wkup_uart0 are brought out on the J784S4 EVM from SoC, but CTS and RTS signal lines are not brought on the EVM. Thus, remove pinmux for CTS and RTS signal lines for wkup_uart0 in J784S4. Fixes: 6fa5d37a2f34 ("arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts") Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com> --- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts index 57e7cb8ea2b8..9f16642ccd5f 100644 --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts @@ -336,8 +336,6 @@ &wkup_pmx2 { wkup_uart0_pins_default: wkup-uart0-default-pins { bootph-all; pinctrl-single,pins = < - J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */ - J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */ J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */ >; -- 2.34.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Bhavya Kapoor <b-kapoor@ti.com> To: <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org> Cc: <nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>, <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>, <conor+dt@kernel.org>, <linux-arm-kernel@lists.infradead.org>, <b-kapoor@ti.com> Subject: [PATCH v3 4/4] arm64: dts: ti: k3-j784s4-evm: Remove Pinmux for CTS and RTS in wkup_uart0 Date: Wed, 14 Feb 2024 16:28:46 +0530 [thread overview] Message-ID: <20240214105846.1096733-5-b-kapoor@ti.com> (raw) In-Reply-To: <20240214105846.1096733-1-b-kapoor@ti.com> Only Tx and Rx Signal lines for wkup_uart0 are brought out on the J784S4 EVM from SoC, but CTS and RTS signal lines are not brought on the EVM. Thus, remove pinmux for CTS and RTS signal lines for wkup_uart0 in J784S4. Fixes: 6fa5d37a2f34 ("arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts") Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com> --- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts index 57e7cb8ea2b8..9f16642ccd5f 100644 --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts @@ -336,8 +336,6 @@ &wkup_pmx2 { wkup_uart0_pins_default: wkup-uart0-default-pins { bootph-all; pinctrl-single,pins = < - J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */ - J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */ J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */ >; -- 2.34.1
next prev parent reply other threads:[~2024-02-14 10:59 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2024-02-14 10:58 [PATCH v3 0/4] arm64: dts: ti: Modify pinmux for wkup_uart0 and mcu_uart0 Bhavya Kapoor 2024-02-14 10:58 ` Bhavya Kapoor 2024-02-14 10:58 ` [PATCH v3 1/4] arm64: dts: ti: k3-j7200-common-proc-board: Modify Pinmux " Bhavya Kapoor 2024-02-14 10:58 ` Bhavya Kapoor 2024-02-14 10:58 ` [PATCH v3 2/4] arm64: dts: ti: k3-j7200-common-proc-board: Remove clock-frequency from mcu_uart0 Bhavya Kapoor 2024-02-14 10:58 ` Bhavya Kapoor 2024-02-14 10:58 ` [PATCH v3 3/4] arm64: dts: ti: k3-j721s2-common-proc-board: Remove Pinmux for CTS and RTS in wkup_uart0 Bhavya Kapoor 2024-02-14 10:58 ` Bhavya Kapoor 2024-02-14 10:58 ` Bhavya Kapoor [this message] 2024-02-14 10:58 ` [PATCH v3 4/4] arm64: dts: ti: k3-j784s4-evm: " Bhavya Kapoor 2024-02-20 3:57 ` [PATCH v3 0/4] arm64: dts: ti: Modify pinmux for wkup_uart0 and mcu_uart0 Vignesh Raghavendra 2024-02-20 3:57 ` Vignesh Raghavendra
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20240214105846.1096733-5-b-kapoor@ti.com \ --to=b-kapoor@ti.com \ --cc=conor+dt@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=kristo@kernel.org \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=nm@ti.com \ --cc=robh+dt@kernel.org \ --cc=vigneshr@ti.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.