[PATCH v2] arm64: dts: renesas: eagle: Add capture overlay for function expansion board

["Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>]

The Eagle board supports an optional "Function expansion board". The
expansion board adds support for HDMI OUT, HDMI capture from two
different sources and eMMC.

This change only adds support for the two HDMI capture sources.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
---
* Changes since v1
- The board is named "Function expansion board", update all references.
- Rename the over lay to r8a77970-eagle-function-expansion.dtso.
- Add r8a77970-eagle-expansion.dtbo to dtb-$(CONFIG_ARCH_R8A77970) so
  it's considered for installation.
- Move #include statements below /.../; markers.
- Sort nodes without addresses in alphabetical order.
- Capitalize i2c -> I2C in comments.
- Use symbolic values for GPIO flags.
- Adjust gpios and output-{low,high} to match that the signal is
  active-low.
- Correct misspelled label and removed unneeded ones.
---
 arch/arm64/boot/dts/renesas/Makefile          |   3 +
 .../r8a77970-eagle-function-expansion.dtso    | 214 ++++++++++++++++++
 2 files changed, 217 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77970-eagle-function-expansion.dtso

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 8ea68d582710..a7d98f286e40 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -62,6 +62,9 @@ dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-ulcb-kf.dtb
 
 dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle.dtb
+dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle-function-expansion.dtbo
+r8a77970-eagle-function-expansion-dtbs := r8a77970-eagle.dtb r8a77970-eagle-function-expansion.dtbo
+dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle-function-expansion.dtb
 dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-v3msk.dtb
 
 dtb-$(CONFIG_ARCH_R8A77980) += r8a77980-condor.dtb
diff --git a/arch/arm64/boot/dts/renesas/r8a77970-eagle-function-expansion.dtso b/arch/arm64/boot/dts/renesas/r8a77970-eagle-function-expansion.dtso
new file mode 100644
index 000000000000..3aa243c5f04c
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a77970-eagle-function-expansion.dtso
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Eagle V3M Function expansion board.
+ *
+ * Copyright (C) 2024 Niklas Söderlund <niklas.soderlund@ragnatech.se>
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	/* CN4 */
+	/* Eagle: SW18 set to OFF */
+	cvbs-in-cn4 {
+		compatible = "composite-video-connector";
+		label = "CVBS IN CN4";
+
+		port {
+			cvbs_con: endpoint {
+				remote-endpoint = <&adv7482_ain7>;
+			};
+		};
+	};
+
+	/* CN2 */
+	/* Eagle: SW35 set 5, 6 and 8 to OFF */
+	hdmi-in-cn2 {
+		compatible = "hdmi-connector";
+		label = "HDMI IN CN2";
+		type = "a";
+
+		port {
+			hdmi_in_con2: endpoint {
+				remote-endpoint = <&adv7612_in>;
+			};
+		};
+	};
+
+	/* CN3 */
+	/* Eagle: SW18 set to OFF */
+	hdmi-in-cn3 {
+		compatible = "hdmi-connector";
+		label = "HDMI IN CN3";
+		type = "a";
+
+		port {
+			hdmi_in_con: endpoint {
+				remote-endpoint = <&adv7482_hdmi>;
+			};
+		};
+	};
+};
+
+/* Disconnect MAX9286 GMSL I2C. */
+&i2c3 {
+	status = "disabled";
+};
+
+/* Connect expansion board I2C. */
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	gpio@27 {
+		compatible = "onnn,pca9654";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		vin0_adv7612_en {
+			gpio-hog;
+			gpios = <3 GPIO_ACTIVE_LOW>;
+			output-high;
+			line-name = "VIN0_ADV7612_ENn";
+		};
+	};
+
+	hdmi-decoder@4c {
+		compatible = "adi,adv7612";
+		reg = <0x4c>, <0x50>, <0x52>, <0x54>, <0x56>, <0x58>;
+		reg-names = "main", "afe", "rep", "edid", "hdmi", "cp";
+		interrupt-parent = <&gpio3>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		default-input = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				adv7612_in: endpoint {
+					remote-endpoint = <&hdmi_in_con2>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				adv7612_out: endpoint {
+					remote-endpoint = <&vin0_in>;
+				};
+			};
+		};
+	};
+
+	video-receiver@70 {
+		compatible = "adi,adv7482";
+		reg = <0x70 0x71 0x72 0x73 0x74 0x75
+		       0x60 0x61 0x62 0x63 0x64 0x65>;
+		reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
+			    "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
+		interrupt-parent = <&gpio3>;
+		interrupts = <03 IRQ_TYPE_LEVEL_LOW>, <04 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "intrq1", "intrq2";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@7 {
+				reg = <7>;
+
+				adv7482_ain7: endpoint {
+					remote-endpoint = <&cvbs_con>;
+				};
+			};
+
+			port@8 {
+				reg = <8>;
+
+				adv7482_hdmi: endpoint {
+					remote-endpoint = <&hdmi_in_con>;
+				};
+			};
+
+			port@a {
+				reg = <10>;
+
+				adv7482_txa: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi40_in>;
+				};
+			};
+		};
+	};
+
+};
+
+&csi40 {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			csi40_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&adv7482_txa>;
+			};
+		};
+	};
+};
+
+&pfc {
+	vin0_pins_parallel: vin0 {
+		groups = "vin0_data12", "vin0_sync", "vin0_clk", "vin0_clkenb";
+		function = "vin0";
+	};
+};
+
+&vin0 {
+	status = "okay";
+
+	pinctrl-0 = <&vin0_pins_parallel>;
+	pinctrl-names = "default";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			vin0_in: endpoint {
+				pclk-sample = <0>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				remote-endpoint = <&adv7612_out>;
+			};
+		};
+	};
+};
+
+&vin1 {
+	status = "okay";
+};
+
+&vin2 {
+	status = "okay";
+};
+
+&vin3 {
+	status = "okay";
+};
-- 
2.43.2