[PATCH v7 11/15] ARM: dts: bcm2835: Add Unicam CSI nodes

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

From: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>

Add both MIPI CSI-2 nodes in the bcm283x tree and take care of the
Raspberry Pi / BCM2711 specific in the related files.

Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
 arch/arm/boot/dts/broadcom/bcm2711.dtsi     |  8 +++++++
 arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi | 14 ++++++++++++
 arch/arm/boot/dts/broadcom/bcm283x.dtsi     | 24 +++++++++++++++++++++
 3 files changed, 46 insertions(+)

diff --git a/arch/arm/boot/dts/broadcom/bcm2711.dtsi b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
index 22c7f1561344..1d8f9f80f935 100644
--- a/arch/arm/boot/dts/broadcom/bcm2711.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
@@ -1114,6 +1114,14 @@ &rmem {
 	#address-cells = <2>;
 };
 
+&csi0 {
+	interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&csi1 {
+	interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 &cma {
 	/*
 	 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
diff --git a/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi
index 7e752a66bf8d..f2aad209187f 100644
--- a/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi
@@ -30,6 +30,20 @@ vchiq: mailbox@7e00b840 {
 	};
 };
 
+&csi0 {
+	clocks = <&clocks BCM2835_CLOCK_CAM0>,
+		 <&firmware_clocks 4>;
+	clock-names = "lp", "vpu";
+	power-domains = <&power RPI_POWER_DOMAIN_UNICAM0>;
+};
+
+&csi1 {
+	clocks = <&clocks BCM2835_CLOCK_CAM1>,
+		 <&firmware_clocks 4>;
+	clock-names = "lp", "vpu";
+	power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>;
+};
+
 &gpio {
 	gpioout: gpioout {
 		brcm,pins = <6>;
diff --git a/arch/arm/boot/dts/broadcom/bcm283x.dtsi b/arch/arm/boot/dts/broadcom/bcm283x.dtsi
index 2ca8a2505a4d..69b0919f1324 100644
--- a/arch/arm/boot/dts/broadcom/bcm283x.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x.dtsi
@@ -454,6 +454,30 @@ dsi1: dsi@7e700000 {
 			status = "disabled";
 		};
 
+		csi0: csi@7e800000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e800000 0x800>,
+			      <0x7e802000 0x4>;
+			reg-names = "unicam", "cmi";
+			interrupts = <2 6>;
+			brcm,num-data-lanes = <2>;
+			status = "disabled";
+			port {
+			};
+		};
+
+		csi1: csi@7e801000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e801000 0x800>,
+			      <0x7e802004 0x4>;
+			reg-names = "unicam", "cmi";
+			interrupts = <2 7>;
+			brcm,num-data-lanes = <4>;
+			status = "disabled";
+			port {
+			};
+		};
+
 		i2c1: i2c@7e804000 {
 			compatible = "brcm,bcm2835-i2c";
 			reg = <0x7e804000 0x1000>;
-- 
Regards,

Laurent Pinchart