From: Kelly Hung <ppighouse@gmail.com>
To: robh+dt@kernel.org
Cc: krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org,
joel@jms.id.au, andrew@codeconstruct.com.au,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org,
openbmc@lists.ozlabs.org, kelly_hung@asus.com,
Allenyy_Hsu@asus.com, Kelly Hung <Kelly_Hung@asus.com>,
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Subject: [PATCH v6 2/2] ARM: dts: aspeed: x4tf: Add dts for asus x4tf project
Date: Tue, 26 Mar 2024 18:35:49 +0800 [thread overview]
Message-ID: <20240326103549.2413515-3-Kelly_Hung@asus.com> (raw)
In-Reply-To: <20240326103549.2413515-1-Kelly_Hung@asus.com>
Base on aspeed-g6.dtsi and can boot into BMC console.
Signed-off-by: Kelly Hung <Kelly_Hung@asus.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
---
v5 -> v6:
- Add Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
- Add Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
- Remove the v3's Reviewed-by: Zev Weiss <zweiss@equinix.com>.
V4 -> V5: None
V3 -> V4: None
V2 -> V3:
- fmc lable change to bmc.
- use 64M partition layout.
- rename spi1 label to bios.
- remove bios partition section.
- add Reviewed-by: Zev Weiss <zweiss@equinix.com>
V1 -> V2:
- do schema check and remove all warings.
- remove all unnecessary sections.
---
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts | 581 ++++++++++++++++++
2 files changed, 582 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index d3ac20e31..32c41f3d9 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-arm-stardragon4800-rep2.dtb \
aspeed-bmc-asrock-e3c246d4i.dtb \
aspeed-bmc-asrock-romed8hm3.dtb \
+ aspeed-bmc-asus-x4tf.dtb \
aspeed-bmc-bytedance-g220a.dtb \
aspeed-bmc-delta-ahe50dc.dtb \
aspeed-bmc-facebook-bletchley.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
new file mode 100644
index 000000000..64f4ed07c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
@@ -0,0 +1,581 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 ASUS Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include "aspeed-g6-pinctrl.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "ASUS-X4TF";
+ compatible = "asus,x4tf-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial4 = &uart5;
+ };
+
+ chosen {
+ stdout-path = "serial4:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ video_engine_memory: video {
+ size = <0x04000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+ <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+ <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+ <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-heartbeat {
+ gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-uid {
+ gpios = <&gpio0 ASPEED_GPIO(P, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ default-state = "off";
+ };
+
+ led-status_Y {
+ gpios = <&gpio1 ASPEED_GPIO(B, 1) GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sys_boot_status {
+ gpios = <&gpio1 ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+};
+
+&adc0 {
+ vref = <2500>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+ &pinctrl_adc2_default &pinctrl_adc3_default
+ &pinctrl_adc4_default &pinctrl_adc5_default
+ &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ vref = <2500>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+ &pinctrl_adc10_default &pinctrl_adc11_default
+ &pinctrl_adc12_default &pinctrl_adc13_default
+ &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&peci0 {
+ status = "okay";
+};
+
+&lpc_snoop {
+ snoop-ports = <0x80>;
+ status = "okay";
+};
+
+&mac2 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii3_default>;
+};
+
+&mac3 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii4_default>;
+};
+
+&fmc {
+ status = "okay";
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+
+ flash@0 {
+ status = "okay";
+ label = "bios";
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ temperature-sensor@49 {
+ compatible = "ti,tmp75";
+ reg = <0x49>;
+ };
+
+ pca9555_4_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_4_22: gpio@22 {
+ compatible = "nxp,pca9555";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_4_24: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ /*A0 - A3 0*/ "", "STRAP_BMC_BATTERY_GPIO1", "", "",
+ /*A4 - A7 4*/ "", "", "", "",
+ /*B0 - B7 8*/ "", "", "", "", "", "", "", "";
+ };
+
+ pca9555_4_26: gpio@26 {
+ compatible = "nxp,pca9555";
+ reg = <0x26>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel_1: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_2: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_3: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_4: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ pca9555_5_24: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70 >;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel_5: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ pca9555_5_5_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "SYS_FAN6", "SYS_FAN5",
+ "SYS_FAN4", "SYS_FAN3",
+ "SYS_FAN2", "SYS_FAN1";
+ };
+
+ pca9555_5_5_21: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ power-monitor@44 {
+ compatible = "ti,ina219";
+ reg = <0x44>;
+ shunt-resistor = <2>;
+ };
+ };
+
+ channel_6: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_7: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_8: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+
+ pca9555_6_27: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_6_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ /*A0 0*/ "", "", "", "", "", "", "", "",
+ /*B0 8*/ "Drive_NVMe1", "Drive_NVMe2", "", "",
+ /*B4 12*/ "", "", "", "";
+ };
+
+ pca9555_6_21: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ idle-state = <1>;
+
+ channel_9: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ temperature-sensor@49 {
+ compatible = "ti,tmp75";
+ reg = <0x49>;
+ };
+
+ power-monitor@40 {
+ compatible = "ti,ina219";
+ reg = <0x40>;
+ shunt-resistor = <2>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina219";
+ reg = <0x41>;
+ shunt-resistor = <5>;
+ };
+ };
+
+ channel_10: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_11: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_12: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@71 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x71>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ channel_13: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_14: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_15: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_16: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c8 {
+ status = "okay";
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ channel_17: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_18: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina219";
+ reg = <0x41>;
+ shunt-resistor = <5>;
+ };
+ };
+
+ channel_19: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_20: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+};
+
+&i2c14 {
+ status = "okay";
+ multi-master;
+
+ eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c08";
+ reg = <0x51>;
+ };
+};
+
+&sgpiom0 {
+ status = "okay";
+ ngpios = <128>;
+};
+
+&video {
+ status = "okay";
+ memory-region = <&video_engine_memory>;
+};
+
+&sdc {
+ status = "okay";
+};
+
+&lpc_snoop {
+ status = "okay";
+ snoop-ports = <0x80>;
+};
+
+&kcs1 {
+ aspeed,lpc-io-reg = <0xca0>;
+ status = "okay";
+};
+
+&kcs2 {
+ aspeed,lpc-io-reg = <0xca8>;
+ status = "okay";
+};
+
+&kcs3 {
+ aspeed,lpc-io-reg = <0xca2>;
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&uart_routing {
+ status = "okay";
+};
+
+&vhub {
+ status = "okay";
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0 0*/ "", "", "", "", "", "", "", "",
+ /*B0 8*/ "", "", "", "", "", "", "PS_PWROK", "",
+ /*C0 16*/ "", "", "", "", "", "", "", "",
+ /*D0 24*/ "", "", "", "", "", "", "", "",
+ /*E0 32*/ "", "", "", "", "", "", "", "",
+ /*F0 40*/ "", "", "", "", "", "", "", "",
+ /*G0 48*/ "", "", "", "", "", "", "", "",
+ /*H0 56*/ "", "", "", "", "", "", "", "",
+ /*I0 64*/ "", "", "", "", "", "", "", "",
+ /*J0 72*/ "", "", "", "", "", "", "", "",
+ /*K0 80*/ "", "", "", "", "", "", "", "",
+ /*L0 88*/ "", "", "", "", "", "", "", "",
+ /*M0 96*/ "", "", "", "", "", "", "", "",
+ /*N0 104*/ "", "", "", "",
+ /*N4 108*/ "POST_COMPLETE", "ESR1_GPIO_AST_SPISEL", "", "",
+ /*O0 112*/ "", "", "", "", "", "", "", "",
+ /*P0 120*/ "ID_BUTTON", "ID_OUT", "POWER_BUTTON", "POWER_OUT",
+ /*P4 124*/ "RESET_BUTTON", "RESET_OUT", "", "HEARTBEAT",
+ /*Q0 128*/ "", "", "", "", "", "", "", "",
+ /*R0 136*/ "", "", "", "", "", "", "", "",
+ /*S0 144*/ "", "", "", "", "", "", "", "",
+ /*T0 152*/ "", "", "", "", "", "", "", "",
+ /*U0 160*/ "", "", "", "", "", "", "", "",
+ /*V0 168*/ "", "", "", "", "", "", "", "",
+ /*W0 176*/ "", "", "", "", "", "", "", "",
+ /*X0 184*/ "", "", "", "", "", "", "", "",
+ /*Y0 192*/ "", "", "", "", "", "", "", "",
+ /*Z0 200*/ "", "", "", "", "", "", "", "";
+};
--
2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Kelly Hung <ppighouse@gmail.com>
To: robh+dt@kernel.org
Cc: krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org,
joel@jms.id.au, andrew@codeconstruct.com.au,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org,
openbmc@lists.ozlabs.org, kelly_hung@asus.com,
Allenyy_Hsu@asus.com, Kelly Hung <Kelly_Hung@asus.com>,
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Subject: [PATCH v6 2/2] ARM: dts: aspeed: x4tf: Add dts for asus x4tf project
Date: Tue, 26 Mar 2024 18:35:49 +0800 [thread overview]
Message-ID: <20240326103549.2413515-3-Kelly_Hung@asus.com> (raw)
In-Reply-To: <20240326103549.2413515-1-Kelly_Hung@asus.com>
Base on aspeed-g6.dtsi and can boot into BMC console.
Signed-off-by: Kelly Hung <Kelly_Hung@asus.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
---
v5 -> v6:
- Add Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
- Add Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
- Remove the v3's Reviewed-by: Zev Weiss <zweiss@equinix.com>.
V4 -> V5: None
V3 -> V4: None
V2 -> V3:
- fmc lable change to bmc.
- use 64M partition layout.
- rename spi1 label to bios.
- remove bios partition section.
- add Reviewed-by: Zev Weiss <zweiss@equinix.com>
V1 -> V2:
- do schema check and remove all warings.
- remove all unnecessary sections.
---
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts | 581 ++++++++++++++++++
2 files changed, 582 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index d3ac20e31..32c41f3d9 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-arm-stardragon4800-rep2.dtb \
aspeed-bmc-asrock-e3c246d4i.dtb \
aspeed-bmc-asrock-romed8hm3.dtb \
+ aspeed-bmc-asus-x4tf.dtb \
aspeed-bmc-bytedance-g220a.dtb \
aspeed-bmc-delta-ahe50dc.dtb \
aspeed-bmc-facebook-bletchley.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
new file mode 100644
index 000000000..64f4ed07c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
@@ -0,0 +1,581 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 ASUS Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include "aspeed-g6-pinctrl.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "ASUS-X4TF";
+ compatible = "asus,x4tf-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial4 = &uart5;
+ };
+
+ chosen {
+ stdout-path = "serial4:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ video_engine_memory: video {
+ size = <0x04000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+ <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+ <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+ <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-heartbeat {
+ gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-uid {
+ gpios = <&gpio0 ASPEED_GPIO(P, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ default-state = "off";
+ };
+
+ led-status_Y {
+ gpios = <&gpio1 ASPEED_GPIO(B, 1) GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sys_boot_status {
+ gpios = <&gpio1 ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+};
+
+&adc0 {
+ vref = <2500>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+ &pinctrl_adc2_default &pinctrl_adc3_default
+ &pinctrl_adc4_default &pinctrl_adc5_default
+ &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ vref = <2500>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+ &pinctrl_adc10_default &pinctrl_adc11_default
+ &pinctrl_adc12_default &pinctrl_adc13_default
+ &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&peci0 {
+ status = "okay";
+};
+
+&lpc_snoop {
+ snoop-ports = <0x80>;
+ status = "okay";
+};
+
+&mac2 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii3_default>;
+};
+
+&mac3 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii4_default>;
+};
+
+&fmc {
+ status = "okay";
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+
+ flash@0 {
+ status = "okay";
+ label = "bios";
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ temperature-sensor@49 {
+ compatible = "ti,tmp75";
+ reg = <0x49>;
+ };
+
+ pca9555_4_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_4_22: gpio@22 {
+ compatible = "nxp,pca9555";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_4_24: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ /*A0 - A3 0*/ "", "STRAP_BMC_BATTERY_GPIO1", "", "",
+ /*A4 - A7 4*/ "", "", "", "",
+ /*B0 - B7 8*/ "", "", "", "", "", "", "", "";
+ };
+
+ pca9555_4_26: gpio@26 {
+ compatible = "nxp,pca9555";
+ reg = <0x26>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel_1: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_2: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_3: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_4: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ pca9555_5_24: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70 >;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel_5: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ pca9555_5_5_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "SYS_FAN6", "SYS_FAN5",
+ "SYS_FAN4", "SYS_FAN3",
+ "SYS_FAN2", "SYS_FAN1";
+ };
+
+ pca9555_5_5_21: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ power-monitor@44 {
+ compatible = "ti,ina219";
+ reg = <0x44>;
+ shunt-resistor = <2>;
+ };
+ };
+
+ channel_6: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_7: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_8: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+
+ pca9555_6_27: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_6_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ /*A0 0*/ "", "", "", "", "", "", "", "",
+ /*B0 8*/ "Drive_NVMe1", "Drive_NVMe2", "", "",
+ /*B4 12*/ "", "", "", "";
+ };
+
+ pca9555_6_21: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ idle-state = <1>;
+
+ channel_9: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ temperature-sensor@49 {
+ compatible = "ti,tmp75";
+ reg = <0x49>;
+ };
+
+ power-monitor@40 {
+ compatible = "ti,ina219";
+ reg = <0x40>;
+ shunt-resistor = <2>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina219";
+ reg = <0x41>;
+ shunt-resistor = <5>;
+ };
+ };
+
+ channel_10: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_11: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_12: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@71 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x71>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ channel_13: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_14: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_15: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_16: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c8 {
+ status = "okay";
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ channel_17: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_18: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina219";
+ reg = <0x41>;
+ shunt-resistor = <5>;
+ };
+ };
+
+ channel_19: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_20: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+};
+
+&i2c14 {
+ status = "okay";
+ multi-master;
+
+ eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c08";
+ reg = <0x51>;
+ };
+};
+
+&sgpiom0 {
+ status = "okay";
+ ngpios = <128>;
+};
+
+&video {
+ status = "okay";
+ memory-region = <&video_engine_memory>;
+};
+
+&sdc {
+ status = "okay";
+};
+
+&lpc_snoop {
+ status = "okay";
+ snoop-ports = <0x80>;
+};
+
+&kcs1 {
+ aspeed,lpc-io-reg = <0xca0>;
+ status = "okay";
+};
+
+&kcs2 {
+ aspeed,lpc-io-reg = <0xca8>;
+ status = "okay";
+};
+
+&kcs3 {
+ aspeed,lpc-io-reg = <0xca2>;
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&uart_routing {
+ status = "okay";
+};
+
+&vhub {
+ status = "okay";
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0 0*/ "", "", "", "", "", "", "", "",
+ /*B0 8*/ "", "", "", "", "", "", "PS_PWROK", "",
+ /*C0 16*/ "", "", "", "", "", "", "", "",
+ /*D0 24*/ "", "", "", "", "", "", "", "",
+ /*E0 32*/ "", "", "", "", "", "", "", "",
+ /*F0 40*/ "", "", "", "", "", "", "", "",
+ /*G0 48*/ "", "", "", "", "", "", "", "",
+ /*H0 56*/ "", "", "", "", "", "", "", "",
+ /*I0 64*/ "", "", "", "", "", "", "", "",
+ /*J0 72*/ "", "", "", "", "", "", "", "",
+ /*K0 80*/ "", "", "", "", "", "", "", "",
+ /*L0 88*/ "", "", "", "", "", "", "", "",
+ /*M0 96*/ "", "", "", "", "", "", "", "",
+ /*N0 104*/ "", "", "", "",
+ /*N4 108*/ "POST_COMPLETE", "ESR1_GPIO_AST_SPISEL", "", "",
+ /*O0 112*/ "", "", "", "", "", "", "", "",
+ /*P0 120*/ "ID_BUTTON", "ID_OUT", "POWER_BUTTON", "POWER_OUT",
+ /*P4 124*/ "RESET_BUTTON", "RESET_OUT", "", "HEARTBEAT",
+ /*Q0 128*/ "", "", "", "", "", "", "", "",
+ /*R0 136*/ "", "", "", "", "", "", "", "",
+ /*S0 144*/ "", "", "", "", "", "", "", "",
+ /*T0 152*/ "", "", "", "", "", "", "", "",
+ /*U0 160*/ "", "", "", "", "", "", "", "",
+ /*V0 168*/ "", "", "", "", "", "", "", "",
+ /*W0 176*/ "", "", "", "", "", "", "", "",
+ /*X0 184*/ "", "", "", "", "", "", "", "",
+ /*Y0 192*/ "", "", "", "", "", "", "", "",
+ /*Z0 200*/ "", "", "", "", "", "", "", "";
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Kelly Hung <ppighouse@gmail.com>
To: robh+dt@kernel.org
Cc: devicetree@vger.kernel.org, conor+dt@kernel.org,
linux-aspeed@lists.ozlabs.org, openbmc@lists.ozlabs.org,
linux-kernel@vger.kernel.org,
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>,
Kelly Hung <Kelly_Hung@asus.com>,
joel@jms.id.au, krzysztof.kozlowski+dt@linaro.org,
Allenyy_Hsu@asus.com, linux-arm-kernel@lists.infradead.org
Subject: [PATCH v6 2/2] ARM: dts: aspeed: x4tf: Add dts for asus x4tf project
Date: Tue, 26 Mar 2024 18:35:49 +0800 [thread overview]
Message-ID: <20240326103549.2413515-3-Kelly_Hung@asus.com> (raw)
In-Reply-To: <20240326103549.2413515-1-Kelly_Hung@asus.com>
Base on aspeed-g6.dtsi and can boot into BMC console.
Signed-off-by: Kelly Hung <Kelly_Hung@asus.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
---
v5 -> v6:
- Add Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
- Add Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
- Remove the v3's Reviewed-by: Zev Weiss <zweiss@equinix.com>.
V4 -> V5: None
V3 -> V4: None
V2 -> V3:
- fmc lable change to bmc.
- use 64M partition layout.
- rename spi1 label to bios.
- remove bios partition section.
- add Reviewed-by: Zev Weiss <zweiss@equinix.com>
V1 -> V2:
- do schema check and remove all warings.
- remove all unnecessary sections.
---
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts | 581 ++++++++++++++++++
2 files changed, 582 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index d3ac20e31..32c41f3d9 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-arm-stardragon4800-rep2.dtb \
aspeed-bmc-asrock-e3c246d4i.dtb \
aspeed-bmc-asrock-romed8hm3.dtb \
+ aspeed-bmc-asus-x4tf.dtb \
aspeed-bmc-bytedance-g220a.dtb \
aspeed-bmc-delta-ahe50dc.dtb \
aspeed-bmc-facebook-bletchley.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
new file mode 100644
index 000000000..64f4ed07c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
@@ -0,0 +1,581 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 ASUS Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include "aspeed-g6-pinctrl.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "ASUS-X4TF";
+ compatible = "asus,x4tf-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial4 = &uart5;
+ };
+
+ chosen {
+ stdout-path = "serial4:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ video_engine_memory: video {
+ size = <0x04000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+ <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+ <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+ <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-heartbeat {
+ gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-uid {
+ gpios = <&gpio0 ASPEED_GPIO(P, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+ default-state = "off";
+ };
+
+ led-status_Y {
+ gpios = <&gpio1 ASPEED_GPIO(B, 1) GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led-sys_boot_status {
+ gpios = <&gpio1 ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+};
+
+&adc0 {
+ vref = <2500>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+ &pinctrl_adc2_default &pinctrl_adc3_default
+ &pinctrl_adc4_default &pinctrl_adc5_default
+ &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ vref = <2500>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+ &pinctrl_adc10_default &pinctrl_adc11_default
+ &pinctrl_adc12_default &pinctrl_adc13_default
+ &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&peci0 {
+ status = "okay";
+};
+
+&lpc_snoop {
+ snoop-ports = <0x80>;
+ status = "okay";
+};
+
+&mac2 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii3_default>;
+};
+
+&mac3 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii4_default>;
+};
+
+&fmc {
+ status = "okay";
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+
+ flash@0 {
+ status = "okay";
+ label = "bios";
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ temperature-sensor@49 {
+ compatible = "ti,tmp75";
+ reg = <0x49>;
+ };
+
+ pca9555_4_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_4_22: gpio@22 {
+ compatible = "nxp,pca9555";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_4_24: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ /*A0 - A3 0*/ "", "STRAP_BMC_BATTERY_GPIO1", "", "",
+ /*A4 - A7 4*/ "", "", "", "",
+ /*B0 - B7 8*/ "", "", "", "", "", "", "", "";
+ };
+
+ pca9555_4_26: gpio@26 {
+ compatible = "nxp,pca9555";
+ reg = <0x26>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel_1: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_2: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_3: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_4: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ pca9555_5_24: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70 >;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel_5: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ pca9555_5_5_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "", "", "", "", "", "", "", "",
+ "", "", "SYS_FAN6", "SYS_FAN5",
+ "SYS_FAN4", "SYS_FAN3",
+ "SYS_FAN2", "SYS_FAN1";
+ };
+
+ pca9555_5_5_21: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ power-monitor@44 {
+ compatible = "ti,ina219";
+ reg = <0x44>;
+ shunt-resistor = <2>;
+ };
+ };
+
+ channel_6: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_7: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_8: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+
+ pca9555_6_27: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pca9555_6_20: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ /*A0 0*/ "", "", "", "", "", "", "", "",
+ /*B0 8*/ "Drive_NVMe1", "Drive_NVMe2", "", "",
+ /*B4 12*/ "", "", "", "";
+ };
+
+ pca9555_6_21: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ idle-state = <1>;
+
+ channel_9: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ temperature-sensor@49 {
+ compatible = "ti,tmp75";
+ reg = <0x49>;
+ };
+
+ power-monitor@40 {
+ compatible = "ti,ina219";
+ reg = <0x40>;
+ shunt-resistor = <2>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina219";
+ reg = <0x41>;
+ shunt-resistor = <5>;
+ };
+ };
+
+ channel_10: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_11: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_12: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@71 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x71>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ channel_13: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_14: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ channel_15: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_16: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c8 {
+ status = "okay";
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ status = "okay";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ channel_17: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ channel_18: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ temperature-sensor@48 {
+ compatible = "ti,tmp75";
+ reg = <0x48>;
+ };
+
+ power-monitor@41 {
+ compatible = "ti,ina219";
+ reg = <0x41>;
+ shunt-resistor = <5>;
+ };
+ };
+
+ channel_19: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ channel_20: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+};
+
+&i2c14 {
+ status = "okay";
+ multi-master;
+
+ eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c08";
+ reg = <0x51>;
+ };
+};
+
+&sgpiom0 {
+ status = "okay";
+ ngpios = <128>;
+};
+
+&video {
+ status = "okay";
+ memory-region = <&video_engine_memory>;
+};
+
+&sdc {
+ status = "okay";
+};
+
+&lpc_snoop {
+ status = "okay";
+ snoop-ports = <0x80>;
+};
+
+&kcs1 {
+ aspeed,lpc-io-reg = <0xca0>;
+ status = "okay";
+};
+
+&kcs2 {
+ aspeed,lpc-io-reg = <0xca8>;
+ status = "okay";
+};
+
+&kcs3 {
+ aspeed,lpc-io-reg = <0xca2>;
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&uart_routing {
+ status = "okay";
+};
+
+&vhub {
+ status = "okay";
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0 0*/ "", "", "", "", "", "", "", "",
+ /*B0 8*/ "", "", "", "", "", "", "PS_PWROK", "",
+ /*C0 16*/ "", "", "", "", "", "", "", "",
+ /*D0 24*/ "", "", "", "", "", "", "", "",
+ /*E0 32*/ "", "", "", "", "", "", "", "",
+ /*F0 40*/ "", "", "", "", "", "", "", "",
+ /*G0 48*/ "", "", "", "", "", "", "", "",
+ /*H0 56*/ "", "", "", "", "", "", "", "",
+ /*I0 64*/ "", "", "", "", "", "", "", "",
+ /*J0 72*/ "", "", "", "", "", "", "", "",
+ /*K0 80*/ "", "", "", "", "", "", "", "",
+ /*L0 88*/ "", "", "", "", "", "", "", "",
+ /*M0 96*/ "", "", "", "", "", "", "", "",
+ /*N0 104*/ "", "", "", "",
+ /*N4 108*/ "POST_COMPLETE", "ESR1_GPIO_AST_SPISEL", "", "",
+ /*O0 112*/ "", "", "", "", "", "", "", "",
+ /*P0 120*/ "ID_BUTTON", "ID_OUT", "POWER_BUTTON", "POWER_OUT",
+ /*P4 124*/ "RESET_BUTTON", "RESET_OUT", "", "HEARTBEAT",
+ /*Q0 128*/ "", "", "", "", "", "", "", "",
+ /*R0 136*/ "", "", "", "", "", "", "", "",
+ /*S0 144*/ "", "", "", "", "", "", "", "",
+ /*T0 152*/ "", "", "", "", "", "", "", "",
+ /*U0 160*/ "", "", "", "", "", "", "", "",
+ /*V0 168*/ "", "", "", "", "", "", "", "",
+ /*W0 176*/ "", "", "", "", "", "", "", "",
+ /*X0 184*/ "", "", "", "", "", "", "", "",
+ /*Y0 192*/ "", "", "", "", "", "", "", "",
+ /*Z0 200*/ "", "", "", "", "", "", "", "";
+};
--
2.25.1
next prev parent reply other threads:[~2024-03-26 10:36 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-03-26 10:35 [PATCH v6 0/2] Add Reviewed-by and Acked-by tags Kelly Hung
2024-03-26 10:35 ` Kelly Hung
2024-03-26 10:35 ` Kelly Hung
2024-03-26 10:35 ` [PATCH v6 1/2] dt-bindings: arm: aspeed: add ASUS X4TF board Kelly Hung
2024-03-26 10:35 ` Kelly Hung
2024-03-26 10:35 ` Kelly Hung
2024-03-26 11:36 ` Krzysztof Kozlowski
2024-03-26 11:36 ` Krzysztof Kozlowski
2024-03-26 18:24 ` Conor Dooley
2024-03-26 18:24 ` Conor Dooley
2024-03-26 18:24 ` Conor Dooley
2024-04-30 1:28 ` Andrew Jeffery
2024-04-30 1:28 ` Andrew Jeffery
2024-04-30 1:28 ` Andrew Jeffery
2024-03-26 10:35 ` Kelly Hung [this message]
2024-03-26 10:35 ` [PATCH v6 2/2] ARM: dts: aspeed: x4tf: Add dts for asus x4tf project Kelly Hung
2024-03-26 10:35 ` Kelly Hung
2024-03-26 11:39 ` Krzysztof Kozlowski
2024-03-26 11:39 ` Krzysztof Kozlowski
2024-03-26 19:12 ` [PATCH v6 0/2] Add Reviewed-by and Acked-by tags Rob Herring
2024-03-26 19:12 ` Rob Herring
2024-03-27 1:46 ` Andrew Jeffery
2024-03-27 1:46 ` Andrew Jeffery
2024-03-27 1:46 ` Andrew Jeffery
2024-03-27 1:54 ` Chia Li Hung
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240326103549.2413515-3-Kelly_Hung@asus.com \
--to=ppighouse@gmail.com \
--cc=Allenyy_Hsu@asus.com \
--cc=andrew@codeconstruct.com.au \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=kelly_hung@asus.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=openbmc@lists.ozlabs.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.