From: Andrew Davis <afd@ti.com>
To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Andrew Davis <afd@ti.com>
Subject: [PATCH 5/6] arm64: dts: ti: k3-j721s2: Remove UART baud rate selection
Date: Tue, 26 Mar 2024 13:54:40 -0500 [thread overview]
Message-ID: <20240326185441.29656-5-afd@ti.com> (raw)
In-Reply-To: <20240326185441.29656-1-afd@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 10 ----------
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 2 --
2 files changed, 12 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index b70c8615e3c15..3cb06a7e4117f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -459,7 +459,6 @@ main_uart0: serial@2800000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x200>;
interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 146 3>;
clock-names = "fclk";
power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
@@ -470,7 +469,6 @@ main_uart1: serial@2810000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02810000 0x00 0x200>;
interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 350 3>;
clock-names = "fclk";
power-domains = <&k3_pds 350 TI_SCI_PD_EXCLUSIVE>;
@@ -481,7 +479,6 @@ main_uart2: serial@2820000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02820000 0x00 0x200>;
interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 351 3>;
clock-names = "fclk";
power-domains = <&k3_pds 351 TI_SCI_PD_EXCLUSIVE>;
@@ -492,7 +489,6 @@ main_uart3: serial@2830000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02830000 0x00 0x200>;
interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 352 3>;
clock-names = "fclk";
power-domains = <&k3_pds 352 TI_SCI_PD_EXCLUSIVE>;
@@ -503,7 +499,6 @@ main_uart4: serial@2840000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02840000 0x00 0x200>;
interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 353 3>;
clock-names = "fclk";
power-domains = <&k3_pds 353 TI_SCI_PD_EXCLUSIVE>;
@@ -514,7 +509,6 @@ main_uart5: serial@2850000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02850000 0x00 0x200>;
interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 354 3>;
clock-names = "fclk";
power-domains = <&k3_pds 354 TI_SCI_PD_EXCLUSIVE>;
@@ -525,7 +519,6 @@ main_uart6: serial@2860000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02860000 0x00 0x200>;
interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 355 3>;
clock-names = "fclk";
power-domains = <&k3_pds 355 TI_SCI_PD_EXCLUSIVE>;
@@ -536,7 +529,6 @@ main_uart7: serial@2870000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02870000 0x00 0x200>;
interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 356 3>;
clock-names = "fclk";
power-domains = <&k3_pds 356 TI_SCI_PD_EXCLUSIVE>;
@@ -547,7 +539,6 @@ main_uart8: serial@2880000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02880000 0x00 0x200>;
interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 357 3>;
clock-names = "fclk";
power-domains = <&k3_pds 357 TI_SCI_PD_EXCLUSIVE>;
@@ -558,7 +549,6 @@ main_uart9: serial@2890000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02890000 0x00 0x200>;
interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 358 3>;
clock-names = "fclk";
power-domains = <&k3_pds 358 TI_SCI_PD_EXCLUSIVE>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index eaf7f709440e6..5ccb04c7c4624 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -298,7 +298,6 @@ wkup_uart0: serial@42300000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x42300000 0x00 0x200>;
interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 359 3>;
clock-names = "fclk";
power-domains = <&k3_pds 359 TI_SCI_PD_EXCLUSIVE>;
@@ -309,7 +308,6 @@ mcu_uart0: serial@40a00000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x40a00000 0x00 0x200>;
interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 149 3>;
clock-names = "fclk";
power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
--
2.39.2
WARNING: multiple messages have this Message-ID (diff)
From: Andrew Davis <afd@ti.com>
To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Andrew Davis <afd@ti.com>
Subject: [PATCH 5/6] arm64: dts: ti: k3-j721s2: Remove UART baud rate selection
Date: Tue, 26 Mar 2024 13:54:40 -0500 [thread overview]
Message-ID: <20240326185441.29656-5-afd@ti.com> (raw)
In-Reply-To: <20240326185441.29656-1-afd@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 10 ----------
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 2 --
2 files changed, 12 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index b70c8615e3c15..3cb06a7e4117f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -459,7 +459,6 @@ main_uart0: serial@2800000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x200>;
interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 146 3>;
clock-names = "fclk";
power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
@@ -470,7 +469,6 @@ main_uart1: serial@2810000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02810000 0x00 0x200>;
interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 350 3>;
clock-names = "fclk";
power-domains = <&k3_pds 350 TI_SCI_PD_EXCLUSIVE>;
@@ -481,7 +479,6 @@ main_uart2: serial@2820000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02820000 0x00 0x200>;
interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 351 3>;
clock-names = "fclk";
power-domains = <&k3_pds 351 TI_SCI_PD_EXCLUSIVE>;
@@ -492,7 +489,6 @@ main_uart3: serial@2830000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02830000 0x00 0x200>;
interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 352 3>;
clock-names = "fclk";
power-domains = <&k3_pds 352 TI_SCI_PD_EXCLUSIVE>;
@@ -503,7 +499,6 @@ main_uart4: serial@2840000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02840000 0x00 0x200>;
interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 353 3>;
clock-names = "fclk";
power-domains = <&k3_pds 353 TI_SCI_PD_EXCLUSIVE>;
@@ -514,7 +509,6 @@ main_uart5: serial@2850000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02850000 0x00 0x200>;
interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 354 3>;
clock-names = "fclk";
power-domains = <&k3_pds 354 TI_SCI_PD_EXCLUSIVE>;
@@ -525,7 +519,6 @@ main_uart6: serial@2860000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02860000 0x00 0x200>;
interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 355 3>;
clock-names = "fclk";
power-domains = <&k3_pds 355 TI_SCI_PD_EXCLUSIVE>;
@@ -536,7 +529,6 @@ main_uart7: serial@2870000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02870000 0x00 0x200>;
interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 356 3>;
clock-names = "fclk";
power-domains = <&k3_pds 356 TI_SCI_PD_EXCLUSIVE>;
@@ -547,7 +539,6 @@ main_uart8: serial@2880000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02880000 0x00 0x200>;
interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 357 3>;
clock-names = "fclk";
power-domains = <&k3_pds 357 TI_SCI_PD_EXCLUSIVE>;
@@ -558,7 +549,6 @@ main_uart9: serial@2890000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02890000 0x00 0x200>;
interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 358 3>;
clock-names = "fclk";
power-domains = <&k3_pds 358 TI_SCI_PD_EXCLUSIVE>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index eaf7f709440e6..5ccb04c7c4624 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -298,7 +298,6 @@ wkup_uart0: serial@42300000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x42300000 0x00 0x200>;
interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 359 3>;
clock-names = "fclk";
power-domains = <&k3_pds 359 TI_SCI_PD_EXCLUSIVE>;
@@ -309,7 +308,6 @@ mcu_uart0: serial@40a00000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x40a00000 0x00 0x200>;
interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
- current-speed = <115200>;
clocks = <&k3_clks 149 3>;
clock-names = "fclk";
power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
--
2.39.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2024-03-26 18:54 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-03-26 18:54 [PATCH 1/6] arm64: dts: ti: k3-am65: Remove UART baud rate selection Andrew Davis
2024-03-26 18:54 ` Andrew Davis
2024-03-26 18:54 ` [PATCH 2/6] arm64: dts: ti: k3-am64: " Andrew Davis
2024-03-26 18:54 ` Andrew Davis
2024-03-26 18:54 ` [PATCH 3/6] arm64: dts: ti: k3-j7200: " Andrew Davis
2024-03-26 18:54 ` Andrew Davis
2024-03-26 18:54 ` [PATCH 4/6] arm64: dts: ti: k3-j721e: " Andrew Davis
2024-03-26 18:54 ` Andrew Davis
2024-03-26 18:54 ` Andrew Davis [this message]
2024-03-26 18:54 ` [PATCH 5/6] arm64: dts: ti: k3-j721s2: " Andrew Davis
2024-03-26 18:54 ` [PATCH 6/6] arm64: dts: ti: k3-j784s4: " Andrew Davis
2024-03-26 18:54 ` Andrew Davis
2024-03-26 20:21 ` [PATCH 1/6] arm64: dts: ti: k3-am65: " Nishanth Menon
2024-03-26 20:21 ` Nishanth Menon
2024-03-26 20:55 ` Andrew Davis
2024-03-26 20:55 ` Andrew Davis
2024-04-09 19:39 ` Nishanth Menon
2024-04-09 19:39 ` Nishanth Menon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240326185441.29656-5-afd@ti.com \
--to=afd@ti.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.